Wayne-Dalton 3322B-Z, 3324B, 3320B Mounting Door Bracket To Series Door, Optional Installations

Page 27

I

Tools Needed:

Power Drill

7/16” Socket

Driver

Mounting Door Bracket To

A 9700 Series Door

IMPORTANT: WHEN CONNECTING A TROLLEY TYPE GARAGE DOOR OPENER TO A 9700 SERIES DOOR, A WAYNE-

DALTON OPENER/TROLLEY BRACKET MUST BE SECURELY ATTACHED TO THE TOP SECTION OF THE DOOR, ALONG WITH ANY U-BARS PROVIDED WITH THE DOOR. THE INSTALLATION OF THE OPENER MUST BE ACCORDING TO MANUFACTURER’S INSTRUCTIONS AND FORCE SETTINGS MUST BE ADJUSTED PROPERLY.

Locate the center of the top section or factory attached u-bar as shown in FIG 1.1.

FOR TOP SECTION WITH U-BAR: Remove and retain 4-6 screws from the center of the u-bar, allowing the door bracket to slide between the section and the u-bar.

Position the door bracket until it seats on the male part of the section as shown in FIG

1.2.The door bracket must be centered and positioned on the top section so it bridges the transition point of the section thickness. Attach the door bracket using

1/4” - 14 x 5/8” self tapping screws as shown in FIG 1.4. Re-attach the u-bar using

(2) 1/4” - 20 x 11/16” self drilling screws through the door bracket as shown in

FIG 1.3. Finish re-attaching the u-bar using the self tapping screws removed previously.

FOR TOP SECTION WITHOUT U-BAR: Position the door bracket until it seats on the male part of the section as shown in FIG

1.2.The door bracket must be centered and positioned on the top section so it bridges the transition point of the section thickness. Attach the door bracket using

1/4” - 14 x 5/8” self tapping screws as shown in FIG 1.4.

NOTE: After completing this step, continue with Step 7.

Door Bracket

Male Part Of Top

Door Bracket

Section

Align Tab With Center

 

Line Of Top Section

 

FIG. 1.1 Or Ubar

FIG. 1.2

Door Bracket

Door Bracket

(2) 1/4”-20 x 11/16”

(8) 1/4”-14 x 5/8”

Self Tapping Screws

Self Drilling Screws

 

FIG. 1.3

FIG. 1.4

 

Door Bracket

Top Section With U-Bar

Door Bracket

Top Section Without U-Bar

OPTIONAL INSTALLATIONS

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 21 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 27
Contents Important Notice Garage Doors & OpenersRev.3 7/19/2007 Package Contents Page Door Test Two Pre-InstallationDisconnect from power source and proceed to assembly Door Test OneSystem Features Tools NeededHomelink Compatibility Rolling Code Technology Definition of key words used in this manual Table of ContentsAttaching Opener to Rail InstallationPositioning and Installing Front Wall Bracket Service PersonReinforce the Header Wall AT Least 3 Feet Long Positioning MotorEnd of Opener Attach Unit to Front Wall BracketMounting Opener End Proper InstallationReinforcing of Your Door Installing LightMounting Door Bracket Manufacturer for ProperGarage Door Wired Wall Station Installation If IncludedDoor can be Seen When Wall Station Near or Next toChildren and in a Location Where Wall Station Installation If IncludedWall Station Near or Next to Garage Door Wall Station OUT of the ReachEntrapment Apply entrapment warning label in aNot adhere Wired Infrared Safety Sensor Installation Sensor to Opener Installation of Wiring for WiredInfrared Safety Sensor Connecting Wired Infrared SafetyCord in Anyway Connecting OpenerConnecting Trolley To Latch AssemblyFully Closed Position Alignment of Wired InfraredSafety Sensors Be Closed by ContinuouslySetting Trolley Close Position ARMTo Avoid Possible Injury or Connecting Door Arm to Door Setting Door Opening Travel Setting Door Close TravelStop Bolt Trolley Opener Contact Obstruction Test Fatal Injury MAY ResultResult from Operating the DOOR/OPENER To Prevent Door Damage or Programming Wireless KeylessEntry If Included Possible Personal InjuryMaterials Important Install ALL WallWood framing using the two screws Surface inside garageInstructions Illustrated Power ConnectionTo Avoid Electrical Shock Important Check Your Local14 x 5/8 self tapping screws as shown in FIG Optional InstallationsTools Needed Power Drill Socket Driver Mounting Door Bracket To Series Door1/4 14 x 5/8 self-tapping screws Must be Adjusted ProperlyShown in FIG With StepStandard Lift Radius Being UsedTrack LOW HeadroomDIM Type of ARM Connecting Door ArmHave to cut straight arm to accomplish Trolley settingsDetermine the WAYNE-DALTON Track Radius Being Used Distance forward To Door , onLOW Headroom Trolley Positioning Chart for Operation Read and Follow ALL InstructionsDoor activation Operating the Wireless Wall Station Opener Controls Customizing the SettingsPrimary Programming for HomeLink to the Prodrive Programming/Training HomeLink UnitTeaching HomeLink to the opener Alternate Programming for HomeLink to the Prodrive Opening Force Adjustment AdjustmentsAdjustment # 1 Opening and Closing Force Closing Force AdjustmentTools Needed None TransmitterWall Station Maintenance Battery Replacement for Wall StationTwice a Year  Troubleshooting MAINTENANCE/ TroubleshootingSymptom Probable Cause Corrective Action Parts Breakdown Rail Assembly All Models Description# Per Unit Description # Per Unit Parts Breakdown Opener Assembly And Accessories All ModelsWireless Keyless Entry Prodrive AccessoriesPre-drill 3/32 pilot hole Drill TemplatePre-drill 5/64 pilot hole Thank you for your purchase Please Do Not Return This Product To The StoreReplacement labor Lifetime Limited WarrantyFCC and IC Statement Patent Information