Wayne-Dalton Complete Guide on Programming ProDrive Garage Door Openers and Remote Units
Page 37

I

Alternate Programming for HomeLink® to the Prodrive ®

NOTE: This Step can only be done on automobiles equipped with the HomeLink® System.

NOTE: Programming HomeLink® requires a Wayne-Dalton Transmitter that is programmed to the opener (the wallstation and transmitter(s) supplied with the opener, come pre-programmed from the factory). Any additional wallstation(s) or transmitter(s) will need to be programmed to the opener, see page 33.

IMPORTANT: Use the programming instructions provided with your vehicle first. Follow these instructions if the HomeLink® unit does not learn the transmitter, when using the vehicle’s instructions.

NOTE: Vehicle may need to be in accessory position when programming. Check car owner’s manual.

NOTE: HomeLink® is a registered trademark of Johnson Controls.

Programming/Training HomeLink® Unit

WARNING

GARAGE DOOR MAY OPERATE DURING PROGRAMMING. TO AVOID POSSIBLE SEVERE OR FATAL INJURY, PLACE THE EMERGENCY DISCONNECT HANDLE IN THE MANUAL OPERATED POSITION.

1.Pull the manual disconnect to put the opener in the disengaged position.

2.Press and hold the two outside buttons on the HomeLink® unit until the HomeLink® indicator light begins to flash rapidly (approx. 20 seconds), then release both buttons. (Do not perform this step to train additional hand-held transmitters.) NOTE: This operation erases all previously learned transmitters and that you need to re-teach any other transmitters to your HomeLink® unit by repeating steps 3 - 6 below.

3.Hold the end of the Wayne-Dalton hand-held transmitter approximately 1 to 3 inches away from the HomeLink® surface keeping the HomeLink® indicator light in view.

4.Use the large button on the Wayne Dalton transmitter. Simultaneously press and hold desired Homelink® button and the Wayne Dalton transmitter large button. Continue to press both buttons counting LED flashes on the HomeLink® module; between 50 to 60 LED flashes the LED will either come on solid or do one “quick flash”; when either of these occur release both Wayne Dalton transmitter and HomeLink® buttons.

Teaching HomeLink® to the opener

5.Press the program switch on the opener. The red program status light on the opener and light will turn on and remain lit for one minute, indicating that it is ready to learn.

6.Press the HomeLink® button used in Step 4 above for 1 to 3 seconds. The program status light on the opener will turn on and off three times indicating a successful learn.

7.Press the HomeLink® the opener will activate and the trolley will travel towards open, the next activation will cause the trolley to travel to the closed position and reengage, subsequent operations will move the door.

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 31 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Garage Doors & Openers Important NoticeRev.3 7/19/2007 Package Contents Page Disconnect from power source and proceed to assembly Pre-InstallationDoor Test One Door Test TwoTools Needed System FeaturesHomelink Compatibility Rolling Code Technology Definition of key words used in this manual Table of ContentsAttaching Opener to Rail InstallationService Person Positioning and Installing Front Wall BracketReinforce the Header Wall End of Opener Positioning MotorAttach Unit to Front Wall Bracket AT Least 3 Feet LongMounting Opener End Proper InstallationMounting Door Bracket Installing LightManufacturer for Proper Reinforcing of Your DoorDoor can be Seen When Wired Wall Station Installation If IncludedWall Station Near or Next to Garage DoorWall Station Near or Next to Garage Door Wall Station Installation If IncludedWall Station OUT of the Reach Children and in a Location WhereApply entrapment warning label in a EntrapmentNot adhere Wired Infrared Safety Sensor Installation Infrared Safety Sensor Installation of Wiring for WiredConnecting Wired Infrared Safety Sensor to OpenerConnecting Trolley Connecting OpenerTo Latch Assembly Cord in AnywaySafety Sensors Alignment of Wired InfraredBe Closed by Continuously Fully Closed PositionARM Setting Trolley Close PositionTo Avoid Possible Injury or Connecting Door Arm to Door Setting Door Opening Travel Setting Door Close TravelStop Bolt Trolley Opener Fatal Injury MAY Result Contact Obstruction TestResult from Operating the DOOR/OPENER Entry If Included Programming Wireless KeylessPossible Personal Injury To Prevent Door Damage orWood framing using the two screws Important Install ALL WallSurface inside garage MaterialsTo Avoid Electrical Shock Power ConnectionImportant Check Your Local Instructions IllustratedTools Needed Power Drill Socket Driver Optional InstallationsMounting Door Bracket To Series Door 14 x 5/8 self tapping screws as shown in FIGShown in FIG Must be Adjusted ProperlyWith Step 1/4 14 x 5/8 self-tapping screwsTrack Radius Being UsedLOW Headroom Standard LiftDIM Type of ARM Connecting Door ArmDetermine the WAYNE-DALTON Track Radius Being Used Trolley settingsDistance forward To Door , on Have to cut straight arm to accomplishLOW Headroom Trolley Positioning Chart for Read and Follow ALL Instructions OperationDoor activation Operating the Wireless Wall Station Opener Controls Customizing the SettingsProgramming/Training HomeLink Unit Primary Programming for HomeLink to the ProdriveTeaching HomeLink to the opener Alternate Programming for HomeLink to the Prodrive Adjustment # 1 Opening and Closing Force AdjustmentsClosing Force Adjustment Opening Force AdjustmentTransmitter Tools Needed NoneWall Station Battery Replacement for Wall Station MaintenanceTwice a Year MAINTENANCE/ Troubleshooting  TroubleshootingSymptom Probable Cause Corrective Action Description Parts Breakdown Rail Assembly All Models# Per Unit Description # Per Unit Parts Breakdown Opener Assembly And Accessories All ModelsWireless Keyless Entry Prodrive AccessoriesDrill Template Pre-drill 3/32 pilot holePre-drill 5/64 pilot hole Thank you for your purchase Please Do Not Return This Product To The StoreReplacement labor Lifetime Limited WarrantyFCC and IC Statement Patent Information
Top Page Image Contents