Wayne-Dalton 3220C-Z, 3324B Positioning Motor, End of Opener, Attach Unit to Front Wall Bracket

Page 9

3Attach Unit to Front Wall Bracket

Tools Needed:

Raise the front end of the rail

 

assembly and attach it to the front wall

7/16” Socket

bracket, using the 1/4” x 4” hex head bolt

 

and the supplied 1/4” plastic insert

Ratchet Wrench

locking nut. Take care not to over tighten

nut. Tighten only until end of bolt is flush

 

Adjustable Wrench

with outside of nut.

 

 

NOTE: If you have a torsion spring

 

counterbalance system, it will be necessary

 

to raise the opener and support it on a

 

step ladder to attach the front end of the rail

 

assembly to the wall bracket.

 

The upper door arm is secured to the spacer

 

bracket with one tie wrap for shipping.

 

Remove tie wrap attaching upper door arm

 

to the spacer bracket, allowing door arm to

 

swing down (see caution).

 

CAUTION: Support upper door arm with your

 

free hand, to prevent door arm from

 

swinging down uncontrolled.

1/4” x 4”

Hex Head Bolt

Upper Door Arm

Front Wall

Bracket

1/4” Plastic Insert

Locking Nut

Tie Wrap

Upper Door Arm

Spacer Bracket

Rail Assembly

Cardboard or Cloth to

Protect the Housing

4

Positioning Motor

 

 

End of Opener

 

 

Tools Needed:

IMPORTANT: TO PREVENT DAMAGE TO

 

DOOR, DO NOT REST THE OPENER ON THE

2” x 4” Board

DOOR WITHOUT USING A 2” X 4” BOARD

 

AT LEAST 3 FEET LONG.

Non-Metallic

 

Step Ladder

Raise the motor end of the opener and

 

support it so you can open the door to its

 

fully open position. You may need help

 

raising motor end if ladder is not high

 

enough.

 

IMPORTANT: TO PREVENT DAMAGE TO

 

DOOR OR OPENER, POSITION TROLLEY AS

 

CLOSE TO OPENER AS POSSIBLE, BEFORE

 

OPENING DOOR.

 

Open the door and place a 2” x 4” x 36”

 

minimum board along the top section of the

 

garage door. Rest the rail assembly on the

 

2” x 4” board.

 

Support top section of door to prevent

 

excessive sagging.

 

 

Rail Assembly

Trolley

2” x 4” Board

DoorOpener

Support Door to

Prevent Sagging

Non-Metallic

Step ladder

Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need 3 You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at www.wayne-dalton.com

Image 9
Contents Important Notice Garage Doors & OpenersRev.3 7/19/2007 Package Contents Page Disconnect from power source and proceed to assembly Pre-InstallationDoor Test One Door Test TwoSystem Features Tools NeededHomelink Compatibility Rolling Code Technology Definition of key words used in this manual Table of ContentsAttaching Opener to Rail InstallationPositioning and Installing Front Wall Bracket Service PersonReinforce the Header Wall End of Opener Positioning MotorAttach Unit to Front Wall Bracket AT Least 3 Feet LongMounting Opener End Proper InstallationMounting Door Bracket Installing LightManufacturer for Proper Reinforcing of Your DoorDoor can be Seen When Wired Wall Station Installation If IncludedWall Station Near or Next to Garage DoorWall Station Near or Next to Garage Door Wall Station Installation If IncludedWall Station OUT of the Reach Children and in a Location WhereEntrapment Apply entrapment warning label in aNot adhere Wired Infrared Safety Sensor Installation Infrared Safety Sensor Installation of Wiring for WiredConnecting Wired Infrared Safety Sensor to OpenerConnecting Trolley Connecting OpenerTo Latch Assembly Cord in AnywaySafety Sensors Alignment of Wired InfraredBe Closed by Continuously Fully Closed PositionSetting Trolley Close Position ARMTo Avoid Possible Injury or Connecting Door Arm to Door Setting Door Opening Travel Setting Door Close TravelStop Bolt Trolley Opener Contact Obstruction Test Fatal Injury MAY ResultResult from Operating the DOOR/OPENER Entry If Included Programming Wireless KeylessPossible Personal Injury To Prevent Door Damage orWood framing using the two screws Important Install ALL WallSurface inside garage MaterialsTo Avoid Electrical Shock Power ConnectionImportant Check Your Local Instructions IllustratedTools Needed Power Drill Socket Driver Optional InstallationsMounting Door Bracket To Series Door 14 x 5/8 self tapping screws as shown in FIGShown in FIG Must be Adjusted ProperlyWith Step 1/4 14 x 5/8 self-tapping screwsTrack Radius Being UsedLOW Headroom Standard LiftDIM Type of ARM Connecting Door ArmDetermine the WAYNE-DALTON Track Radius Being Used Trolley settingsDistance forward To Door , on Have to cut straight arm to accomplishLOW Headroom Trolley Positioning Chart for Operation Read and Follow ALL InstructionsDoor activation Operating the Wireless Wall Station Opener Controls Customizing the SettingsPrimary Programming for HomeLink to the Prodrive Programming/Training HomeLink UnitTeaching HomeLink to the opener Alternate Programming for HomeLink to the Prodrive Adjustment # 1 Opening and Closing Force AdjustmentsClosing Force Adjustment Opening Force AdjustmentTools Needed None TransmitterWall Station Maintenance Battery Replacement for Wall StationTwice a Year  Troubleshooting MAINTENANCE/ TroubleshootingSymptom Probable Cause Corrective Action Parts Breakdown Rail Assembly All Models Description# Per Unit Description # Per Unit Parts Breakdown Opener Assembly And Accessories All ModelsWireless Keyless Entry Prodrive AccessoriesPre-drill 3/32 pilot hole Drill TemplatePre-drill 5/64 pilot hole Thank you for your purchase Please Do Not Return This Product To The StoreReplacement labor Lifetime Limited WarrantyFCC and IC Statement Patent Information