Emerson manual Rosemount 3051N

Page 93

Reference Manual

00809-0100-4808, Rev CA June 2008

Rosemount 3051N

Message		Description

ROM checksum		Checksum of transmitter software has detected a fault. Return
error ON		to Rosemount Nuclear Instruments, Inc. for repair.

Save data from		Prompts user to press SAVE softkey to initiate a
device to		device-to-memory transfer.
configuration
memory

Saving data to		Data is being transferred from a device to configuration
configuration		memory.
memory.

Sending data to		Data is being transferred from configuration memory to a
device.		device.

Sensor board not		The sensor module electronics board is not initialized. Return
initialized ON		to Rosemount Nuclear Instruments, Inc. for repair.

There are write only		There are write-only variables which have not been set by the
variables which		user. These variables should be set or invalid values may be
have not been		sent to the device.
edited. Please edit
them.

There is unsent data.		Press YES to send unsent data and turn the HC off. Press NO
Send it before		to turn the HC off and lose the unsent data.
shutting off?

Too few data bytes		Command returns fewer data bytes than expected as
received		determined by the device description.

Transmitter Fault		Device returns a command response indicating a fault with the
		connected device.

Units for <variable		The engineering units for this variable have been edited. Send
label> has changed.		engineering units to the device before editing this variable.
Unit must be sent
before editing, or
invalid data will be
sent.

Unsent data to		There is unsent data for a previously connected device which
online device. SEND		must be sent or thrown away before connecting to another
or LOSE data		device.

Upgrade 275		The communicator does not contain the most recent
software to access		Rosemount 3051N Device Descriptors (DDs). Select YES to
XMTR function.		communicate using the existing DDs. Select NO to abort
Continue with old		communication.
description?

Use up/down arrows		Gives direction to change the contrast of the HC display.
to change contrast.
Press DONE when
done.

A-17

Image 93

Contents Reference Manual Important Notice -- Errata Rosemount 3051N Return of Material Changes from June 2006 to June OldChanges Rosemount 3051N Table of Contents Installation TroubleshootingSpecifications Reference Data Options Appendix aHart Communicator Glossary Index Section Introduction Using this ManualRosemount 3051N Transmitter Functions Overview Safety MessagesAlarm Level Verification TransmitterSecurity Physical Removal Local Zero and Span Local Keys Configuring Transmitter Alarm and Security Jumper ProcedureElectronics Board Setting the Loop to Manual Wiring Diagrams Bench Hook-up Wiring Diagrams Field Hook-up Review Configuration Data Check OutputProcess Variables Basic Setup Sensor TemperatureSet Process Variable Units Set OutputRerange with a Communicator Only RerangeRerange with a Pressure Input Source and a Communicator Span and Zero Adjustment Buttons Diagnostics Service Detailed SetupTransmitter Test Loop TestCalibration Transmitter Bench Calibration Tasks Field Calibration Tasks Calibration Overview Configure the Analog Output ParametersURV Sensor TrimTypical Zero vs Non-zero-Based Application Illustrations Zero TrimDigital Trim Connection Drawing 4-20 mA Transmitters Full TrimRecall Factory Trim Recall Factory Trim- Sensor Trim Digital-to-Analog Trim Using Other ScaleRecall Factory Trim- Analog Output Analog Output TrimZero Effect HTc = URV + S URV Ps Rosemount 3051N Section Installation Rosemount 3051N Typical Installation Flowchart General Considerations Special Draft Range ConsiderationsMechanical Considerations 156 181 16 x 11/4 Bolts for Mounting to 54.1 Transmitter 120 127 66.8 Traditional Flange Option Code H2 Dimensional Drawing Mounting Rosemount 3051N GAS or Liquid Service GAS Service Steam Service Process Connections Housing Rotation Power SupplyElectrical Considerations Power Supply Load Limitations WiringAccess Requirements Cover Installation Grounding the Transmitter CaseEnvironmental Considerations Troubleshooting Returning Rosemount Products and Materials Symptom Corrective ActionsSeismic Nuclear SpecificationsModel Range Code Hydrostatic Test Pressure Ambient Temperature Effect12 Performance SpecificationsReference Accuracy DriftOverpressure Effect Static Pressure Effect Power Supply Effect Load Effect Mounting Position EffectRange Code Overpressure Effect Range Code Static Pressure Zero Effect1Service Functional SpecificationsTemperature Limits OutputSpan and Zero, Zero Elevation, Suppression Range Minimum Span Upper URL Lower LRLRange Code Minimum Time Constant Tc Including Dead Time Td Pressure12 Maximum WorkingStatic Pressure Limits Overpressure Limits Burst PressurePhysical Specifications Materials of Construction Option Code Description Add Ordering Information Housing Material Conduit Entry Size Configuration InformationMounting Bracket Options Meters optionalDate On Rosemount 3051N Exploded View with Coplanar Process Flange Rosemount 3051N Rosemount 3051N Section Options Overview Safety Messages LCD MeterCustom Meter Configuration Exploded View of the Rosemount 3051N with Optional LCD Meter Installing the MeterRosemount 3051N Error Diagnostic MessagesPress Limit Mounting Brackets OperationTransient Protection Terminal Block T1 Traditional Flange H2Transient Protection Terminal Block T1 Rosemount 3051N Appendix a Hart Communicator Introduction Safety MessagesRosemount 3051N Online Menu Function Hart Fast Key Sequence Connections and Hardware Figure A-3. Rosemount Hart terminal access doorFigure A-4. Bench Hook-up MA Transmitters Rosemount Communicator KeysAction Keys Function Keys Alphanumeric and Shift KeysData Entry Fast Key Sequence Conventions Fast Key Sequence Example Fast Key SequencesMenus Functions Main MenuOnline Menu Touch Multifunction LED Alphanumeric KeysTouch Screen Multifunction LED Processing IndicationRosemount 3051N Diagnostic Messages Fast Key Sequences Hot Key optionsMessage Description Rosemount 3051N Uploadvariable Rosemount 3051N Rosemount 3051N Glossary Smart Family Index 00809-0100-4808, Rev CA June Security Page ¢00809-0100-4801V¤