Frymaster CF Series Troubleshooting Abnormal Burner Operation, Flame is visible, and burner is

Page 47

CF SERIES GAS FRYERS

CHAPTER 6: OPERATOR TROUBLESHOOTING

6.5 Troubleshooting Abnormal Burner Operation

	PROBLEM	PROBABLE CAUSES	CORRECTIVE ACTION
		A. Burner gas pressure is too high.	A. Call FASC to adjust pressure to
	Flame is visible	B. Gas valve vent tube clogged.	recommended standard.
	Flame is visible
	above flue opening		B. Remove and clean vent tube and
	and burner is		B. Remove and clean vent tube and
	and burner is	C. Gas valve regulator defective.	reinstall.
	excessively noisy.	C. Gas valve regulator defective.	reinstall.
			C. Call FASC to replace gas valve.
	Fryer is operating		Shut the fryer down and clean the gas
	normally, but flames	Obstructed gas valve vent tube.	valve vent tube in accordance the
	are rolling out of the	Obstructed gas valve vent tube.	instructions on Page 5-5 of this
	front of the burner.		manual.

6-7

Image 47

Contents APRIL Installation andCF Series Gas FryersREQUIREMENTS in Chapter 2 of this manual for specifics Page CHAPTER 6 Operator Troubleshooting TABLE OF CONTENTSCHAPTER 2 Installation Instructions CHAPTER 5 Preventive Maintenance1.1 Applicability and Validity 1.2 Parts Ordering and Service InformationCF SERIES GAS FRYERS CHAPTER 1 INTRODUCTION CF SERIES GAS FRYERS CHAPTER 1 INTRODUCTION 1.3 Safety Information1.4 European Community CE Specific Information CE Standard for Incoming Gas Pressures1.5 Equipment Description 1.7 Definitions 1.6 Installation, Operating, and Service PersonnelWarranty on your equipment 1.8 Shipping Damage Claim Procedure 2.1 General Installation Requirements CF SERIES GAS FRYERS CHAPTER 2 INSTALLATION INSTRUCTIONSThe fryers must be installed with a 6 150 mm clearance at both sides and back when installed adjacent to combustible construction no clearance is required when installed adjacent to noncombustible construction. A minimum of 24 600 mm clearance should be provided at the front of the fryer The type of gas for which the fryer is equipped is stamped on the data plate attached to the inside of the fryer door. Connect a fryer stamped NAT only to natural gas, those stamped PRO only to propane gas, and those stamped MFG only to manufactured gas 2.3 Pre-Connection Preparations 2.2 Caster/Leg Installation4. Test the fryer electrical system 2.4 Connection to Gas Line CE Standard 2.5 Converting to Another Gas Type CE Gas Conversion Instructions Non-CE Gas Conversion InstructionsNon-CE Only 2-10CE Only CE Gas Valve 3.1 Start-Up ProcedureCF SERIES GAS FRYERS CHAPTER 3 OPERATING INSTRUCTIONS Non-CE Gas Valveleast five minutes before attempting to re-light ACCESSING THE PILOTCF SERIES GAS FRYERS CHAPTER 3 OPERATING INSTRUCTIONS LIGHTING THE PILOT ON NON-CE FRYERS1. Ensure power to the unit is OFF, and then press the OFF red button. Wait 5 minutes branded locations 3.2 Boiling-Out the Frypot5. For units equipped with a Computer Magic III.5 Computer 3.4 Controller Operation and Programming 3.3 Shutting the Fryer Down4.1 Draining and Manual Filtering CF SERIES GAS FRYERS CHAPTER 4 FILTRATION INSTRUCTIONSIf you are using a Frymaster filter cone holder, be sure that the cone holder rests securely on the metal container 4.2 Filter Magic II Filtration System Operation 4.2 Filter Magic II Filtration System Operation cont 7. Replace the crumb tray in the filter pan 1. To filter the oil, bring oil to operating temperature and turn the fryer power OFF. Then open the drain valve on the fryer you have selected to be filtered. If necessary, use the Fryer’s Friend steel rod to clear the drain from inside the frypot as necessary of the fryer and may cause injury CF SERIES GAS FRYERS CHAPTER 4 FILTRATION INSTRUCTIONS DANGERDrain handle in the closed position Clean Fryer Cabinet Inside and Out CF SERIES GAS FRYERS CHAPTER 5 PREVENTATIVE MAINTENANCE5.1 Fryer Preventive Maintenance Checks and Services Inspect Fryer and Accessories for DamageDrain and Clean Frypot Check Recovery TimeClean Float Switch and Shaft Clean Detachable Parts and Accessories Check Computer Magic III Set Point Accuracy Clean Gas Valve Vent TubeCheck Thermostat Controller Thermostat Calibration Check Burner Manifold Pressure Fryer 5.3 Annual/Periodic System InspectionBuilt-In Filtration System 6.1 Introduction CF SERIES GAS FRYERS CHAPTER 6 OPERATOR TROUBLESHOOTINGSolid state analog controller power andBurner will not lightCM III.5 displays indicator does notindicator is on but mode. contUnit will not go into 6.3 Troubleshooting Fryers with Thermostat Controls6.4 Troubleshooting the Built-In Filtration System Burner does nottransfer takes place 6.4 Troubleshooting the Built-In Filtration System contfiltering. cont Pump starts, but nospraying properly Power Shower is notor the transfer is very slow. contand burner is 6.5 Troubleshooting Abnormal Burner OperationFlame is visible above flue opening6.6 Replacing the Controller or Controller Wiring Harness THIS PAGE INTENTIONALLY LEFT BLANK Price $12.00 SERVICE HOTLINEShipping Address 8700 Line Avenue, Shreveport, Louisiana FAX Parts 1-318-219-7140 FAX Tech Support