USER | Menu | PICTURE | Menu | INPUT | Menu | OUTPUT | Menu | AUDIO | Menu | ||||||
PRESETS |
| CONTROL |
| CONFIG |
| CONFIG |
|
| CONFIG |
| |||||
|
|
|
|
|
| ||||||||||
| Next |
|
| Next |
|
| Next |
|
| Next |
|
|
| Next |
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
INx RECALL | (x)H | POS | V | INPUT #x | RESOLUTION | VOLUME |
<N/A> | +00000+00000 | RGB | 1080p@60 | |||
ADVANCED | Menu |
| VIEW COMM | Menu | EXIT MENU? | ||||
CONFIG |
|
|
| SETTINGS |
|
| PRESS NEXT | ||
|
|
|
| ||||||
| Next |
|
|
| Next |
|
| ||
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| ||
AUTO IMAGE |
|
| SERIAL PORT |
|
| ||||
Input #x OFF |
|
| 9600 | RS232 |
|
| |||
Rotate either to select a preset to recall settings.
Next
INx SAVE <02>
Rotate either
to select a preset to save current settings to.
Rotate 
to adjust horizontal position. Rotate 
to adjust vertical position.
Next
(x)H SIZE V 00000 00000
Rotate 
to adjust horizontal size. Rotate 
to adjust vertical size.
Rotate either to select input signal type.
Next
(x)FILM MODE
OFF
Rotate either to turn film mode off or to Auto.
Next
Rotate 
to select resolution.
Rotate 
to select refresh rate
Next
VGA FORMAT
RGBHV
Rotate either to select the VGA format.
Rotate either to set volume level.
Next
AUDIO MUTE <OFF> ON
Rotate either to turn audio mute on or off.
Next
INx GAIN/ATT
Rotate 
to turn Auto Image mode on or off.
Next
ASPECT RATIO
IN#x FILL
Rotate either to select aspect ratio mode.
Next
Next
MAC ADRESS 005A6078CEC
This is set at the factory and cannot be changed in “Edit Comm Settings”
menu. Next
DHCP MODE
On
“Hidden” Menu *
EDIT COMM
SETTINGS
Next
SERIAL PORT
9600 RS232
Rotate 
to select
Rotate
to change
NOTE: Where used in this flow chart “x” indicates the input number.
Next
(x)BRIT CONT
064* *064
Rotate 
to adjust brightness.
Rotate 
to adjust contrast (* = default).
Next
(x)COL TINT
064* *064
Rotate 
to adjust color.
Rotate 
to adjust tint (* = default).
Next
(x)DETAIL *064
Rotate either to
(x)H START V
128 128
Rotate 
to adjust horizontal start. Rotate 
to adjust vertical start.
Next
(x)H ACT V 1024* *0768
Rotate 
to adjust horizontal active pixels. Rotate 
to adjust vertical active pixels (* = default).
Next
(x)TPIX PHAS
1344* 01
Rotate to adjust
Next
Rotate either to set sync values.
Next
HDMI FORMAT
AUTO
Rotate either to set HDMI format.
Next
HDCP NOTE
OFF <ON>
Rotate either to turn HDCP note on or off.
0 dB
Rotate either to set gain and attenuation level.
Next
INx FORMAT
DIGITAL
Rotate either to select input audio format.
Next
AUDIO OUTPUT
STEREO
Rotate either to select audio output format.
AUTO MEMORY |
| Next | |
IN#x ON | I | 192.168 | |
Rotate either to turn | |||
P | 254.254 | ||
auto memory on |
|
| |
or off for selected input. IP address | Next | ||
Next | S | 255.255 | |
| |||
OVERSCAN | M | 000.000 | |
Subnet mask | Next | ||
| |||
|
| ||
Rotate either to set | G | 192.168 | |
the overscan mode. | |||
Next | W | 000.000 | |
Gateway address | |||
| |||
SWITCH TYPE
DISSOLVE
Rotate either to change switch type.
Next
baud rate.
Next
DHCP MODE
<ON>
Rotate either to turn
DHCP mode on or off.
| Next |
I | 192.168 |
P | 254.254 |
Rotate
to select octet field. Rotate 
to change IP address.
| Next |
|
|
S | 255.255 |
M | 000.000 |
Rotate 
to select octet field. Rotate 
to change Subnet address.
set detail level (* = default).
total pixels (* = default). Rotate 
to adjust phase.
Next
INx EDID
1600x1200@60
Rotate
to set an EDID value for the active input.
Next
GENLOCK/AFL
OFF
Rotate either to set genlock mode.
Next
H OFFSET V
110 75
Rotate 
to adjust horizontal offset.
TEST PATTERN
COLOR BARS
Rotate either to change test pattern.
Next
OSD DURATION
125 SEC
Rotate either to change OSD duration.
Next
| Next |
|
|
G | 192.168 |
W | 000.000 |
Rotate 
to select octet field. Rotate
to change Gateway address.
*NOTE: To activate the hidden menu “Edit Comms”, press and hold input 5 and Next buttons simultaneously for three seconds.
To exit the Edit Comms menu press Menu.
DVS 605 • Operation
NOTE: The Input Configuration submenus are input specific and some menus may not be available depending on the input type.
Rotate 
to adjust vertical offset.
TEMPERATURE
96 F 35 C
Indicates internal temperature (not adjustable).
Next
FACT. RESET
HOLD AUTO
Press and hold Auto button
to reset unit to factory settings.
15