Extron electronic DVS 605 manual Audio Configuration All Models, Audio Delay Setting

Page 28
Audio Configuration (All Models)

Audio Configuration (All Models)

Audio Configuration allows the user to set volume level (0 dB to -100 dB range), turn audio mute on or off, adjust input gain and attenuation levels (–53 dB to +9 dB range) for the current analog input. It also allows selection of an input audio format (none, analog,

2-channel digital, full digital, 2-channel auto, or full auto), and the audio output type (stereo or dual mono), which can be adjusted for each input.

NOTE: Volume level and input gain and attenuation adjustments are only available on

audio models (DVS 605 A and DVS 605 AD).

 

 

 

• For analog inputs 1 and 2, the choice of input audio format is analog or none.

• For non-audio models format selection for inputs 3 through 5 is limited to

none, 2-channel digital, or full digital.

 

 

 

 

• For inputs 3, 4, and 5, when in auto mode, digital audio is used when

 

present. If no digital audio is present it defaults to analog audio.

 

AUDIO

Next

VOLUME

Next

AUDIO MUTE

Next

IN4 GAIN/ATT

Next

CONFIG

 

-75dB

 

<OFF> ON

 

0 dB

 

Rotate either to

Rotate either to

set volume level.

turn audio mute

 

on or off.

Rotate either to set gain and attenuation level.

Next

 

 

Next

IN4 FORMAT

DIGITAL

 

 

Rotate either to select input audio format.

AUDIO OUTPUT

STEREO

Rotate either to select audio output format.

Figure 17. Audio Configuration Menu

Use the Next button to scroll to the applicable submenu, and user both Adjust knobs ([ {) to change the settings as needed.

Input Audio Format

Description

None

All audio for the input is muted: 128 byte EDID (VGA/DVI) is presented to the source.

 

 

Analog

5-pole captive screw connector is used for audio input: 128 byte EDID (VGA/DVI) is

 

presented to the source.

 

 

2-channel digital

256 byte EDID (HDMI) is presented to the source requesting 2CH PCM audio.

 

 

Full digital

256 byte EDID (HDMI) is presented to the source allowing for all digital audio formats.

 

 

NOTE:

DVS 605 anlog audio outputs are active only if analog or PCM audio is detected on HDMI

inputs 3,4, and 5.

2-channel auto

256 byte EDID (HDMI) is presented to the source requesting 2CH PCM audio.

 

If digital audio is not present this automatically defaults to the 5-pole captive screw

 

analog audio input.

 

 

Full auto

256 byte EDID (HDMI) is presented to the source allowing for all digital audio formats.

 

If digital audio is not present this automatically defaults to the 5-pole captive screw

 

analog audio input.

 

 

Audio Delay Setting

The DVS automatically delays all analog and digital audio inputs to compensate for internal video processing delay. Occasionally additional audio delay is required to account for other signal processors, scalers, or display devices in a system. For these situations, the DVS 605 offers an additional 0-255 ms static global audio delay which can be set via SIS command or internal web pages to eliminate audio “lip sync” issues.

DVS 605 • Operation

22

Page 27 Page 29
Image 28
Page 27 Page 29
Contents SCALERS AND SIGNAL PROCESSORS with Seamless SwitchingUser Guide HDCP-CompliantScalerSafety Instructions Safety Instructions • EnglishChinese Simplified（简体中文） Instructions de sécurité • FrançaisCopyright FCC Class A NoticeTrademarks Specifications Availability Software CommandsConventions Used in this Guide NotificationsUsing the Default Web Pages ContentsSIS Communication and Control Mounting the DVS Introduction DVS 605 Series DescriptionLicensed Third-partySoftware Used in the DVS Licensed Third-partySoftware Used in the DVSPackage LicenseVideo Inputs Key FeaturesVideo Outputs General AudioDVS 605 • Introduction DVS 605 • Introduction Controlling the DVS DVS 605 Rear Panel Features — All Models Rear Panel ConnectionsRear Panel Cabling FigureDVS using the LockIt bracket as follows Figure 2. LockIt Bracket Mounting Options Audio Input Connector WiringFigure Figure 5. Audio Output Connector Wiring Figure 4. Audio Output Connector WiringFigure 6. RJ-45LAN Connector Wiring DVS 605 • Rear Panel Connections •Front Panel Overview •Powering Up •Other DVS 605 Operating FeaturesFigure 7. DVS 605 Front Panel Features OperationPowering Up Default Display CycleMenu Navigation Using Front Panel Controls Figure 8. Typical Default Display CycleMenu Overview Figure 9. Top Level MenusFigure 10. Main Menu DVS 605 • OperationUser Presets Figure 11. User Preset MenuPicture Control Figure 12. Picture Control MenuInput Configuration Figure 13. Input Configuration MenuInput video types InputResolutions and Refresh Rates Output ConfigurationFigure 14. Output Configuration Menu Analog Output Format Sync PolarityHDMI Format HDCP NotificationHDCP Authorized HDCP Status: Inputs & OutputsGenlock/AFL Modes Genlock/AFL Offset Description Audio Delay Setting Audio Configuration All ModelsFigure 17. Audio Configuration Menu Figure 18. Advanced Configuration Menu Advanced ConfigurationAspect Ratio Auto-Image Auto-Imagethreshold settingsAuto Memory Switch type OverscanTest pattern OSD durationView Comm Settings Factory ResetFigure 21. Edit Comm Settings Menu Exit MenuFront Panel Lockout Executive Modes Figure 22. Front Panel LockoutEnable Executive Mode Disable Executive ModeWindow vs. Image Size Position — An Overview DVS 605 OperationFront Panel Activation Picture-in-picturePIP ModeNOTES PIP Presets Figure 24. Default Main and PIP Window LayoutsOther DVS 605 Operating Features Power SaveCustom EDID/Custom Output Resolution Screen SaveHardwired IR Port The OSD BugAudio Format Audio SourceResetting the Unit DVS 605 Reset Mode SummaryFigure 25. Reset Mode Comparison Reset All IP Reset to Factory Defaults SettingsSIS Communication and Control Copyright Information•Commands and Responses Host to Scaler CommunicationsCommands and Responses Password InformationError Responses Error Response ReferencesSymbol Definitions DVS 605 • SIS Communication and ControlFigure 29. SIS Command EDID Table DVS 605 SIS Communication and ControlDVS 605 SIS Communication and Control DVS 605 • SIS Communication and Control SIS IP command definitions DVS 605 • SIS Communication and ControlDVS 605 • SIS Communication and Control SIS Command and Response Table CommandASCII Command ResponseAdditional Description Input nameAuto-Image Horizontal startCommand ASCII CommandResponse Additional DescriptionPicture Adjustments Video muteColor TintHorizontal position window Vertical position windowHorizontal position image Vertical position imageOutput Configuration Power save modeHorizontal size image Output scaler rateAudio Configuration Audio mute global settings Volume control audio models onlyAudio delay available on all models CommandAudio input format Audio output formatAudio follow CommandPresets User presets User preset nameInput presets Input preset nameAdvanced Configuration Test patternFreeze Auto memories per inputVideo effect Effect durationFront panel security lockout Executive Mode HDCP notification green screen/messageVideo signal presence GenlockGenlock/AFL Offset CommandHardwired IR port Reset commandsPicture In Picture PIP on/offBackup/restore configuration Information requestProduct naming CommandEthernet data port Firmware version requestsCommand ASCII TelnetIP setup commands Information requestsCommand ASCII TelnetNOTE: E X12!CA Directory commands File erase commandsRe-mapport designations CommandUsing the Default Web Pages Accessing the Default Web Pages•Accessing the Default Web Pages Navigating the Default Web PagesTo check compatibility view settings Navigating the Default Web PagesTurning Off Compatibility Mode Configuration Pages AV Controls PanelAuto-Imagebutton AV input buttons inputsVideo and audio mute buttons Breakaway audio check box audio models onlyFreeze button Signal type Figure 34. Input Configuration PanelInput renaming RGB ScaledAspect ratio Film DetectAuto-Image Auto MemoryResolution Analog signal formatFigure 35. Input Configuration Panel Refresh rateDigital output signal format Switch transitionGenlock Test patternEDID Minder Page Figure 36. EDID Minder PageAssigning EDIDs Figure 37. Assigning EDIDsSignal Sampling Image Settings PageFigure 38. Image Settings Page User Presets Settings Included Within PresetsSetting User PresetInput Presets OverscanPIP Settings Page Figure 40. PIP Settings PagePIP input selection Snap PIP toPIP picture controls Size and PositionHorizontal Size and Vertical Size fields Horizontal Pos and Vertical Pos fieldsPIP presets Figure 41. PIP Preset Default Window LocationsAudio Settings Page Figure 42. Audio Config PageNone •2-CHDigital •Full DigitalDual Mono StereoPreset Management Page Figure 43. Preset Management Pagea.Recall: Inputs, Size & Position, or b.Recall: Size & Position OnlyDevice Settings Page Figure 44. Device Settings PageScreen Saver Settings 1.Select the Enable On Screen Display check boxOn Screen Display Message HDCP NotificationAuto Switch Hardware Pages Unit Information PageFigure 46. Unit Information Page See Licensed Third-partySoftware Used in theConnection Settings Page Figure 48. Connection Settings PageDevice Name Page Figure 47. Device Name PageRS-232Settings Ethernet SettingsFirmware Loader Page Figure 49. Firmware Loader PageFigure 50. Executive/Power Mode Page Executive/Power Mode PageExecutive Mode Power Mode Date and Time PageMute Video and Sync Figure 51. Date and Time PagePassword Page Figure 52. Password PageFigure 53. Reset Device Page Reset Device Pagedevice name, DHCP setting, and port mapping Tabletop Placement MountingMounting the DVS UL Guidelines for Rack Mounted DevicesRack Mounting Furniture MountingFigure 54. Rack Mounting the DVS Figure 55. Furniture Mounting the DVSExtron Warranty USA, Canada, South Americaand Central America Japan
Related manuals
Manual 4 pages 24.4 Kb
Top Page Image Contents