Extron electronic DVS 605 Analog Output Format, Sync Polarity, HDMI Format, HDCP Notification

Page 25

Analog Output Format

When a new custom rate has been captured or uploaded, the on-screen display (OSD) dynamically updates with the new rate for that custom slot. For example if a custom 480p EDID is uploaded to slot C1, the LCD would read “C1: 720x480”. These five custom slots are shared between custom output resolutions (based on preferred timings 1 block) and custom EDID tables, which can be assigned to any DVS input.

Analog Output Format

Using either of the Adjust knobs ([ {), select the output video format required by the display: RGBHV (default), RGBS, RGsB, YUV bi-level, and YUV tri-level.

Sync Polarity

Some display devices may require a particular combination of horizontal (H) and vertical

(V)sync signal polarities. Select the appropriate combination of positive or negative H and V sync by rotating either the Adjust horizontal ([) or the Adjust vertical ({) knob.

NOTE: If the output format was specified as RGsB or YUV, or RGBS, this submenu

will not be displayed because this menu is only applicable for RGBHV.

HDMI Format

Using either of the Adjust knobs ([ {), select the HDMI format as follows:

•Auto — (based on sink EDID), default

•DVI RGB 444

•HDMI RGB 444 FULL (0-255, audio, InfoFrames)

•HDMI YUV 444 FULL (0-255, audio, InfoFrames)

•HDMI YUV 444 LIMT (16-235, audio, InfoFrames)

•HDMI YUV 422 FULL (0-255, audio, InfoFrames)

•HDMI YUV 422 LIMT (16-235, audio, InfoFrames)

HDCP Notification

The HDCP Notification provides a means of determining if HDCP content restrictions are preventing a video signal from passing. The DVS 605 has the ability to notify the user that they are currently trying to view HDCP protected content through a non-HDCP compliant output port (15-pin HD or 3G/HD-SDI) or a non-HDCP compliant HDMI/DVI display. The options presented to the user during this scenario are the ability to show a green screen with a moving “OSD bug” (see page 32) reading “HDCP CONTENT,” or to disable this message, and instead output muted (black) video on non-HDCP compliant displays.

The HDCP Notification setting can be adjusted via the front panel menu by using either of the Adjust knobs ([ {), to turn HDCP notification on or off.

HDCP CONTENT

Figure 15. Green HDCP Notification Screen

It can also be adjusted via the internal web pages or SIS commands.

DVS 605 • Operation

19

Image 25

Contents with Seamless Switching SCALERS AND SIGNAL PROCESSORSUser Guide HDCP-CompliantScalerSafety Instructions • English Safety InstructionsChinese Simplified（简体中文） Instructions de sécurité • FrançaisCopyright FCC Class A NoticeTrademarks Software Commands Specifications AvailabilityConventions Used in this Guide NotificationsUsing the Default Web Pages ContentsSIS Communication and Control Mounting the DVS DVS 605 Series Description IntroductionLicensed Third-partySoftware Used in the DVS Licensed Third-partySoftware Used in the DVSPackage LicenseVideo Inputs Key FeaturesVideo Outputs General AudioDVS 605 • Introduction DVS 605 • Introduction Controlling the DVS Rear Panel Connections DVS 605 Rear Panel Features — All ModelsRear Panel Cabling FigureDVS using the LockIt bracket as follows Figure 2. LockIt Bracket Mounting Options Audio Input Connector WiringFigure Figure 5. Audio Output Connector Wiring Figure 4. Audio Output Connector WiringFigure 6. RJ-45LAN Connector Wiring DVS 605 • Rear Panel Connections •Other DVS 605 Operating Features •Front Panel Overview •Powering UpFigure 7. DVS 605 Front Panel Features OperationDefault Display Cycle Powering UpMenu Navigation Using Front Panel Controls Figure 8. Typical Default Display CycleFigure 9. Top Level Menus Menu OverviewDVS 605 • Operation Figure 10. Main MenuFigure 11. User Preset Menu User PresetsPicture Control Figure 12. Picture Control MenuFigure 13. Input Configuration Menu Input ConfigurationInput video types InputResolutions and Refresh Rates Output ConfigurationFigure 14. Output Configuration Menu Sync Polarity Analog Output FormatHDMI Format HDCP NotificationHDCP Authorized HDCP Status: Inputs & OutputsGenlock/AFL Modes Genlock/AFL Offset Description Audio Delay Setting Audio Configuration All ModelsFigure 17. Audio Configuration Menu Figure 18. Advanced Configuration Menu Advanced ConfigurationAspect Ratio Auto-Image Auto-Imagethreshold settingsAuto Memory Overscan Switch typeTest pattern OSD durationFactory Reset View Comm SettingsFigure 21. Edit Comm Settings Menu Exit MenuFigure 22. Front Panel Lockout Front Panel Lockout Executive ModesEnable Executive Mode Disable Executive ModeDVS 605 Operation Window vs. Image Size Position — An OverviewFront Panel Activation Picture-in-picturePIP ModeNOTES Figure 24. Default Main and PIP Window Layouts PIP PresetsPower Save Other DVS 605 Operating FeaturesCustom EDID/Custom Output Resolution Screen SaveThe OSD Bug Hardwired IR PortAudio Format Audio SourceDVS 605 Reset Mode Summary Resetting the UnitFigure 25. Reset Mode Comparison Reset All IP Reset to Factory Defaults SettingsCopyright Information SIS Communication and Control•Commands and Responses Host to Scaler CommunicationsPassword Information Commands and ResponsesError Responses Error Response ReferencesDVS 605 • SIS Communication and Control Symbol DefinitionsDVS 605 SIS Communication and Control Figure 29. SIS Command EDID TableDVS 605 SIS Communication and Control DVS 605 • SIS Communication and Control DVS 605 • SIS Communication and Control SIS IP command definitionsDVS 605 • SIS Communication and Control Command SIS Command and Response TableASCII Command ResponseInput name Additional DescriptionAuto-Image Horizontal startASCII Command CommandResponse Additional DescriptionVideo mute Picture AdjustmentsColor TintVertical position window Horizontal position windowHorizontal position image Vertical position imagePower save mode Output ConfigurationHorizontal size image Output scaler rateVolume control audio models only Audio Configuration Audio mute global settingsAudio delay available on all models CommandAudio output format Audio input formatAudio follow CommandUser preset name Presets User presetsInput presets Input preset nameTest pattern Advanced ConfigurationFreeze Auto memories per inputEffect duration Video effectFront panel security lockout Executive Mode HDCP notification green screen/messageGenlock Video signal presenceGenlock/AFL Offset CommandReset commands Hardwired IR portPicture In Picture PIP on/offInformation request Backup/restore configurationProduct naming CommandFirmware version requests Ethernet data portCommand ASCII TelnetInformation requests IP setup commandsCommand ASCII TelnetNOTE: E X12!CA File erase commands Directory commandsRe-mapport designations CommandAccessing the Default Web Pages Using the Default Web Pages•Accessing the Default Web Pages Navigating the Default Web PagesTo check compatibility view settings Navigating the Default Web PagesTurning Off Compatibility Mode AV Controls Panel Configuration PagesAuto-Imagebutton AV input buttons inputsVideo and audio mute buttons Breakaway audio check box audio models onlyFreeze button Figure 34. Input Configuration Panel Signal typeInput renaming RGB ScaledFilm Detect Aspect ratioAuto-Image Auto MemoryAnalog signal format ResolutionFigure 35. Input Configuration Panel Refresh rateSwitch transition Digital output signal formatGenlock Test patternFigure 36. EDID Minder Page EDID Minder PageFigure 37. Assigning EDIDs Assigning EDIDsSignal Sampling Image Settings PageFigure 38. Image Settings Page Settings Included Within Presets User PresetsSetting User PresetOverscan Input PresetsFigure 40. PIP Settings Page PIP Settings PagePIP input selection Snap PIP toSize and Position PIP picture controlsHorizontal Size and Vertical Size fields Horizontal Pos and Vertical Pos fieldsFigure 41. PIP Preset Default Window Locations PIP presetsFigure 42. Audio Config Page Audio Settings PageNone •2-CHDigital •Full DigitalStereo Dual MonoFigure 43. Preset Management Page Preset Management Pagea.Recall: Inputs, Size & Position, or b.Recall: Size & Position OnlyFigure 44. Device Settings Page Device Settings Page1.Select the Enable On Screen Display check box Screen Saver SettingsOn Screen Display Message HDCP NotificationAuto Switch Unit Information Page Hardware PagesFigure 46. Unit Information Page See Licensed Third-partySoftware Used in theFigure 48. Connection Settings Page Connection Settings PageDevice Name Page Figure 47. Device Name PageEthernet Settings RS-232SettingsFirmware Loader Page Figure 49. Firmware Loader PageFigure 50. Executive/Power Mode Page Executive/Power Mode PageExecutive Mode Date and Time Page Power ModeMute Video and Sync Figure 51. Date and Time PageFigure 52. Password Page Password PageFigure 53. Reset Device Page Reset Device Pagedevice name, DHCP setting, and port mapping Mounting Tabletop PlacementMounting the DVS UL Guidelines for Rack Mounted DevicesFurniture Mounting Rack MountingFigure 54. Rack Mounting the DVS Figure 55. Furniture Mounting the DVSUSA, Canada, South America Extron Warrantyand Central America Japan

Related manuals

Manual 4 pages 24.4 Kb