Extron electronic DVS 605 Overscan, Switch type, Test pattern, OSD duration, Test Pattern Choices

Page 31
Overscan

Overscan

Use the horizontal Adjust knob ([) to select input video type (RGB, YUV, RGBcvS, S-video, composite, or HDMI), and the vertical Adjust knob ({) to select the overscan mode (None, 2.5% or 5.0%).

Overscan is specific to each input signal type. This zooms and crops SMPTE inputs to mask edge effects and ancillary data that are common in broadcast signals. Issuing an Auto‑Image with overscan enabled, runs an Auto Phase routine (YUV and RGB only) and centers and sizes the input according to table values.

NOTE: Overscan is valid only on SMPTE input rates (NTSC, PAL, 480p, 576p, 720p,

1080i, or 1080p).

Switch type

This enables a video switch transition (cut or dissolve) when switching between inputs. Use either of the Adjust knobs ([ {) to select the switch type as desired.

NOTE: Input switches between input 4 and input 5 use a fade through black

transition.

Test pattern

The built-in test patterns are useful for calibrating a display to the DVS 605 output. Choose a test pattern such as crop, alternating pixels, and color bars to adjust the image.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Color Bars

Crosshatch 4x4 Crosshatch

 

Grayscale

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ramp

 

 

Alternating

Alternating

 

 

 

 

 

 

 

Pixels

Lines

White Field

Crop

1.33 Aspect

1.78 Aspect

1.85 Aspect

2.35 Aspect

Blue Mode

Figure 20. Test Pattern Choices

•Alternating Pixels — Used to calibrate input sampling of the display devices to the device output. Use this pattern to adjust the clocking and phasing at the display until no more vertical bands are visible.

•Crop — Used to center the output on the display device: adjust H and V to center the display until all four crop lines are visible.

•Color Bars — Used to calibrate color settings on the display and to confirm proper system wiring.

•Blue Mode — This assists the user in setting up the color and tint levels

Use either the Adjust horizontal ([) or Adjust vertical ({) knob to select a test pattern. The default state is Off.

OSD duration

The DVS 605 displays a small OSD “bug” in the upper left corner when switching between input. This bug contains information regarding the detected input rate and format, the HDCP status of the selected input, and an indication of Main vs. PIP inputs. The duration that the OSD bug is on-screen (in seconds) can be set from 1 to 500 seconds via the front panel menu. It can also be set to “No OSD” or Always On”.

The duration can also be set via the internal web pages, or by SIS commands.

DVS 605 • Operation

25

Page 30 Page 32
Image 31
Page 30 Page 32
Contents HDCP-CompliantScaler SCALERS AND SIGNAL PROCESSORSwith Seamless Switching User GuideInstructions de sécurité • Français Safety InstructionsSafety Instructions • English Chinese Simplified（简体中文）Copyright FCC Class A NoticeTrademarks Notifications Specifications AvailabilitySoftware Commands Conventions Used in this GuideUsing the Default Web Pages ContentsSIS Communication and Control Mounting the DVS DVS 605 Series Description IntroductionLicense Licensed Third-partySoftware Used in the DVSLicensed Third-partySoftware Used in the DVS PackageVideo Inputs Key FeaturesVideo Outputs General AudioDVS 605 • Introduction DVS 605 • Introduction Controlling the DVS Figure DVS 605 Rear Panel Features — All ModelsRear Panel Connections Rear Panel CablingDVS using the LockIt bracket as follows Figure 2. LockIt Bracket Mounting Options Audio Input Connector WiringFigure Figure 5. Audio Output Connector Wiring Figure 4. Audio Output Connector WiringFigure 6. RJ-45LAN Connector Wiring DVS 605 • Rear Panel Connections Operation •Front Panel Overview •Powering Up•Other DVS 605 Operating Features Figure 7. DVS 605 Front Panel FeaturesFigure 8. Typical Default Display Cycle Powering UpDefault Display Cycle Menu Navigation Using Front Panel ControlsFigure 9. Top Level Menus Menu OverviewDVS 605 • Operation Figure 10. Main MenuFigure 12. Picture Control Menu User PresetsFigure 11. User Preset Menu Picture ControlInput Input ConfigurationFigure 13. Input Configuration Menu Input video typesResolutions and Refresh Rates Output ConfigurationFigure 14. Output Configuration Menu HDCP Notification Analog Output FormatSync Polarity HDMI FormatHDCP Authorized HDCP Status: Inputs & OutputsGenlock/AFL Modes Genlock/AFL Offset Description Audio Delay Setting Audio Configuration All ModelsFigure 17. Audio Configuration Menu Figure 18. Advanced Configuration Menu Advanced ConfigurationAspect Ratio Auto-Image Auto-Imagethreshold settingsAuto Memory OSD duration Switch typeOverscan Test patternExit Menu View Comm SettingsFactory Reset Figure 21. Edit Comm Settings MenuDisable Executive Mode Front Panel Lockout Executive ModesFigure 22. Front Panel Lockout Enable Executive ModeDVS 605 Operation Window vs. Image Size Position — An OverviewFront Panel Activation Picture-in-picturePIP ModeNOTES Figure 24. Default Main and PIP Window Layouts PIP PresetsScreen Save Other DVS 605 Operating FeaturesPower Save Custom EDID/Custom Output ResolutionAudio Source Hardwired IR PortThe OSD Bug Audio FormatReset All IP Reset to Factory Defaults Settings Resetting the UnitDVS 605 Reset Mode Summary Figure 25. Reset Mode ComparisonHost to Scaler Communications SIS Communication and ControlCopyright Information •Commands and ResponsesError Response References Commands and ResponsesPassword Information Error ResponsesDVS 605 • SIS Communication and Control Symbol DefinitionsDVS 605 SIS Communication and Control Figure 29. SIS Command EDID TableDVS 605 SIS Communication and Control DVS 605 • SIS Communication and Control DVS 605 • SIS Communication and Control SIS IP command definitionsDVS 605 • SIS Communication and Control Response SIS Command and Response TableCommand ASCII CommandHorizontal start Additional DescriptionInput name Auto-ImageAdditional Description CommandASCII Command ResponseTint Picture AdjustmentsVideo mute ColorVertical position image Horizontal position windowVertical position window Horizontal position imageOutput scaler rate Output ConfigurationPower save mode Horizontal size imageCommand Audio Configuration Audio mute global settingsVolume control audio models only Audio delay available on all modelsCommand Audio input formatAudio output format Audio followInput preset name Presets User presetsUser preset name Input presetsAuto memories per input Advanced ConfigurationTest pattern FreezeHDCP notification green screen/message Video effectEffect duration Front panel security lockout Executive ModeCommand Video signal presenceGenlock Genlock/AFL OffsetPIP on/off Hardwired IR portReset commands Picture In PictureCommand Backup/restore configurationInformation request Product namingASCII Telnet Ethernet data portFirmware version requests CommandASCII Telnet IP setup commandsInformation requests CommandNOTE: E X12!CA Command Directory commandsFile erase commands Re-mapport designationsNavigating the Default Web Pages Using the Default Web PagesAccessing the Default Web Pages •Accessing the Default Web PagesTo check compatibility view settings Navigating the Default Web PagesTurning Off Compatibility Mode AV input buttons inputs Configuration PagesAV Controls Panel Auto-ImagebuttonVideo and audio mute buttons Breakaway audio check box audio models onlyFreeze button RGB Scaled Signal typeFigure 34. Input Configuration Panel Input renamingAuto Memory Aspect ratioFilm Detect Auto-ImageRefresh rate ResolutionAnalog signal format Figure 35. Input Configuration PanelTest pattern Digital output signal formatSwitch transition GenlockFigure 36. EDID Minder Page EDID Minder PageFigure 37. Assigning EDIDs Assigning EDIDsSignal Sampling Image Settings PageFigure 38. Image Settings Page User Preset User PresetsSettings Included Within Presets SettingOverscan Input PresetsSnap PIP to PIP Settings PageFigure 40. PIP Settings Page PIP input selectionHorizontal Pos and Vertical Pos fields PIP picture controlsSize and Position Horizontal Size and Vertical Size fieldsFigure 41. PIP Preset Default Window Locations PIP presets•2-CHDigital •Full Digital Audio Settings PageFigure 42. Audio Config Page NoneStereo Dual Monob.Recall: Size & Position Only Preset Management PageFigure 43. Preset Management Page a.Recall: Inputs, Size & Position, orFigure 44. Device Settings Page Device Settings PageHDCP Notification Screen Saver Settings1.Select the Enable On Screen Display check box On Screen Display MessageAuto Switch See Licensed Third-partySoftware Used in the Hardware PagesUnit Information Page Figure 46. Unit Information PageFigure 47. Device Name Page Connection Settings PageFigure 48. Connection Settings Page Device Name PageFigure 49. Firmware Loader Page RS-232SettingsEthernet Settings Firmware Loader PageFigure 50. Executive/Power Mode Page Executive/Power Mode PageExecutive Mode Figure 51. Date and Time Page Power ModeDate and Time Page Mute Video and SyncFigure 52. Password Page Password PageFigure 53. Reset Device Page Reset Device Pagedevice name, DHCP setting, and port mapping UL Guidelines for Rack Mounted Devices Tabletop PlacementMounting Mounting the DVSFigure 55. Furniture Mounting the DVS Rack MountingFurniture Mounting Figure 54. Rack Mounting the DVSJapan Extron WarrantyUSA, Canada, South America and Central America
Related manuals
Manual 4 pages 24.4 Kb
Top Page Image Contents