|
|
| GEAppliances.com |
|
| Select Options (Continued) | |
5 |
| ||
| Steam | For use with heavily soiled and/or | |
|
| ||
|
| (Prewash) | starting the cycle. The Steam option adds approximately 30 minutes to the cycle time. This option is |
|
| (on some models) | available with Heavy, Auto Sense, and Normal cycles. |
|
| Wash | Selecting either the Upper or Lower Wash Zones will target dishwashing of just one rack. This will |
|
| Zones | shorten the cycle time and conserve energy. This option can be used when there is only half a |
|
| (on some models) | load of dishes. |
|
| Delay | Delays the start of a wash cycle up to 8 to 12 hours depending on model. Press Delay Hours, to select |
|
| Hours | the number of hours, then press Start one time to begin countdown. The cycle will start once allotted time |
|
| (on some models) | has expired. |
|
|
|
|
|
| Control | You can lock the controls to prevent selections from being made. You can also lock the controls |
|
| Lock | after you have started a cycle to prevent cycle changes. For example, children cannot accidentally |
|
|
| start the dishwasher by pressing pads with this option selected. |
|
|
| To LOCK the dishwasher control, depending on the model, press and hold the Heated Dry pad for 3 seconds or |
|
|
| press and hold the Steam and Wash Temp pads at the same time for 3 seconds. The Control Lock light will turn |
|
|
| on to indicate the control is locked. |
|
|
| To UNLOCK the dishwasher control, depending on the model, press and hold the Heated Dry pad for 3 second |
|
|
| or press and hold the Steam and Wash Temp pads at the same time for 3 seconds. The Control Lock light |
|
|
| will turn off to indicate the control is unlocked. |
|
|
|
|
|
| Energy | When connected to a smart meter and your electric company, the dishwasher will automatically delay starting |
|
| Smart | a cycle during the more expensive peak demand times, and run when demand is low. However, you can override |
|
|
| the delay settings and use the dishwasher as needed. Learn more about Energy Smart under the Using the |
|
|
| Dishwasher section. |
|
|
| |
|
| Start Dishwasher | |
6 |
| ||
|
| Start | Door can be open to select the desired options. Press the Start pad and close the door within 10 seconds |
|
|
| to start the cycle or begin the Delay Hours countdown. The wash cycle will begin shortly after closing |
|
|
| the door. If the door is open, the illuminated lights will turn off if a pad is not pressed within two minutes. |
|
|
| To activate the display, close and open the door or press any pad. |
|
|
|
|
|
| Interrupt | To interrupt or pause a dish cycle, slowly open the door. Opening the door will cause the wash cycle to |
|
| or Pause | pause. The dishwasher will beep every minute to remind you to close the door. To restart or resume |
|
|
| the cycle, press Start, and close the door. |
|
| Cancel | To cancel a wash cycle, press and hold the Start pad for 3 seconds and close door. The dishwasher will drain, |
|
|
| emit a beep sound, and the wash cycle light will turn OFF. |
|
|
| |
|
| Cycle Completion | |
7 |
| ||
|
| Sanitized | Displayed at the end of the cycle when Wash Temp Sani (Sanitize) has been selected and the dishwasher |
|
|
| has met the requirements for sanitization. See Wash Temp Sani, for complete option description. |
|
|
| Opening the door or pressing any key while the door is closed will turn off the light. |
|
|
|
|
|
| Clean | Displayed when a wash cycle is complete. The light stays ON as a reminder that the dishes are clean. Opening |
|
|
| the door or pressing any key while the door is closed will turn the light off. |
5