Pitco Frialator L20-332 manual Model SG6H Fryerinstallation Installation Clearances

Page 7

MODEL SG6H FRYERINSTALLATION

1.2. INSTALLATION CLEARANCES

The clearances shown below are for combustible and non-combustible installations and will allow for safe and proper operation of your appliance.

Back

Sides

Floor

Combustible Construction

Non Combustible Construction

Inches (centimeters)

Inches (centimeters)

6.0" (15.24cm)

0.0" (0.0cm)

6.0" (15.24cm)

0.0" (0.0cm)

6.0" (15.24cm)

6.0" (15.24cm)

In addition to the above clearances there must also be at least 16 inches (40.64cm) of aisle space in front of the unit.

WARNING

DO NOT obstruct the flow of ventilation, or air openings around the appliance. Adequate clearance around the appliance is necessary for servicing and proper component ventilation. Ensure that you meet the minimum clearance requirements specified in this manual.

WARNING

DO NOT install this appliance next to a water cooker. A splash over of water into the hot oil may cause a flash fire.

CAUTION

To prevent equipment damage and/or personal injury, do not tilt the appliance onto any two of its casters or legs, or pull the appliance by the splash back.

1.3. LEG/CASTER INSTALLATION AND LEVELING

When you receive your appliance it is completely assembled with the possible exception of the legs (or casters). This appliance must be installed with legs or casters; it cannot be curb mounted. Curb mounting will seriously inhibit this appliance’s ability to effect proper component ventilation. The legs/casters must be installed before connecting the appliance to the power supply. The legs/casters provide the necessary height to meet sanitation requirements and assure adequate air supply to the combustion system. Use the following procedure.

WARNING

This appliance must be installed with the legs or casters provided by the manufacturer.

Required tools: 7/16 “ wrench and socket and a large pair of water pump pliers.

1.Lay the appliance on its back, being careful not to damage the splash back by pulling on it. Protect the outside of the appliance with cardboard or a drop cloth when laying it down.

2.Attach each leg/caster with the hex head screws and nuts supplied. Each leg/caster requires four ¼-20 x 5/8” hex head screws and nuts. Insure that all screws are tight.

3.Mount the screws from the inside of the appliance with the nut on the outside (bottom) of the appliance. The nuts have lock washers attached to them, therefore it is not necessary to use separate lock washers.

WARNING

DO NOT install legs or casters, or perform leveling procedure when appliance is in operation or full of hot liquids. Serious injury could result.

4.When all four legs/casters are securely mounted, stand the unit up, being careful not to put too much weight on any one leg. Adjust the height and level the appliance by adjusting the leveling devices (B) with water pump pliers. On casters, loosen 2 screws (A) before leveling, make your height adjustments, then retighten.

L20-332, rev. 1 (05/11)

3

Page 6 Page 8
Image 7
Page 6 Page 8
Contents English To the PURCHASER, Owner and Store Manager Model SG6H Fryer Operation Features Specific to Models with FiltersControl BOX & Electrical Components ANNUAL/PERIODIC Preventative Maintenance and InspectionFiltering with a Filter Drawer if Equipped Replacing the Filter Media if EquippedSelf Cleaning Burner System not on ALL Models Checking Your NEW Appliance Accessories DescriptionSG6H SFSG6H LEG/CASTER Installation and Leveling Model SG6H Fryerinstallation Installation ClearancesGAS Connection Fuel Supply Line Leak and Pressure TestingQuick Disconnect Connection CE GAS Table not Applicable to ALL Models InstallationElectrical Connections Inspection Ventilation and Fire Safety SystemsON/OFF Initial AdjustmentsFilling the Appliance Lighting InstructionsOFF Main Burner System Adjustment Initial Cleaning Operational Features Drain Valve Handle Blue Shown in the closed position Self Cleaning Burner System if equippedFilter Pump Reset Button Cook Tank Front PanelFilling the Tank with Liquid Shortening Filling the Cooker TankTank Capacity Model SG6HModel SG6H Fryer Appliance Start UP Fry Thickness 350F 360F 370F Typical Timer ButtonsCooking Cooking TipsAppliance Shutdown Standby ModeComplete Shutdown Flush Hose Operation if Equipped Daily Preventative MaintenanceAppliance Inspection Preventative MaintenanceFilter Cleaning if Equipped Cleaning the Cook TankDo not leave the appliance unattended during cleaning Cleaning the CabinetBoil OUT Procedure Monthly Preventative MaintenanceMechanical Inspection Temperature CheckVentilation Hood Filter System if EquippedHigh Temperature Limit Power FailureDrain Valve Interlock L20-332, rev 05/11 Filter Troubleshooting Chart if Equipped Troubleshooting ChartsFryer Troubleshooting Chart Problem Probable Causes Corrective ActionsDisplay Explanation Action TroubleshootingL20-332, rev 05/11

L20-332 specifications

The Pitco Frialator L20-332 is an exceptional commercial deep fryer designed for high-volume frying operations. Delivers reliability, efficiency, and advanced technology tailored for busy kitchens, this unit is a top choice for restaurants, cafes, and catering services. Its robust construction and innovative designs make it ideal for frying a variety of foods, from crispy French fries to golden chicken wings.

One of the standout features of the L20-332 is its high production capacity. With a generous 40 lbs. oil capacity per tank, the fryer is capable of supporting large batches, making it possible to keep up with customer demand during peak hours. The fryer is equipped with two fry tanks, providing a total oil capacity of 80 lbs., which allows chefs to prepare multiple items simultaneously, enhancing productivity and efficiency.

The Pitco Frialator L20-332 incorporates advanced heating technology that ensures even heating throughout the oil. This unit utilizes a highly efficient gas burner system that optimizes energy consumption while delivering consistent frying temperatures. The ability to quickly recover heat after food is added ensures that cooks maintain optimal frying conditions without significant temperature drops, which is crucial for achieving perfectly cooked food.

Additionally, this fryer features a durable stainless steel exterior that not only enhances its aesthetic appeal but also makes it easy to clean and maintain. The stainless steel construction resists rust and corrosion, ensuring longevity even in the busiest kitchen environments. Its adjustable legs allow for easy installation and adaptability to various kitchen layouts.

Safety is paramount in any commercial kitchen, and the L20-332 addresses this with effective features such as an integrated high-limit temperature control and a manual reset for safe operation. An easily accessible drain valve simplifies oil changes and maintenance, allowing for efficient cleaning routines.

Easy-to-use controls provide operators with precise temperature settings and cooking times, ensuring consistency and quality in every dish. The design of the fryer also includes a built-in filtration system that extends oil life and boosts the flavor of fried products, resulting in cost savings for the business.

In summary, the Pitco Frialator L20-332 is a powerful and reliable deep fryer equipped with advanced features designed for high-volume cooking. Its combination of efficient heating technology, user-friendly controls, and durable materials make it an ideal addition to any commercial kitchen looking to maximize productivity while delivering exceptional food quality.
Top Page Image Contents