Garland MP-GS, MP-GD-10-S service manual Display Messages, Cooking with shelf timers

Page 25

Repeat steps 4 through 7 for each individual shelf position/shelf timer key that will be used..

9..After programming all the shelf timers that will be used, press the Program key.. This will return the oven to idle mode..

Cooking with shelf timers:

1..Press the numeric key corresponding to the desired profile, (fan setting, temperature and time; see ‘To program shelf timers:’ on the previous page).. Allow the oven to heat to the programmed temperature.. When the programmed temperature has been reached, the display will indicate READY..

2..Load product on the desired shelf, close the door, and press the same key that was pressed in Step 1.. The display will indicate ENTER SHELF..

Press the numeric key, (1 - 6), corresponding to the shelf loaded.. Press the Start/Cancel key to engage the timer countdown for the selected shelf..

3..Repeat Step 2 up to five times while loading the remaining shelves..

Note: The display will show only one timer countdown at a time. The shortest, (time remaining), of all the active shelf timers will be displayed.

4..When the shortest of the active shelf timers has expired, the display will indicate DONE SHELF X, where X equals the number of the shelf timer that has expired, and an audible alarm will sound continuously for 10 seconds.. The LED on the expired timer’s key will flash.. Press that timer key to cancel the alarm, unload the finished product from the corresponding shelf immediately and close the door..

The timer display will change to show the countdown of the shortest of the remaining active shelf timers.. Repeat this step until all of the active timers have expired and their respective shelves are unloaded..

If the alarm is not canceled after sounding continuously for 10 seconds, it will sound a short tone once every 15 seconds until the corresponding shelf timer key is pressed.. The display will continue to indicate SHELF X and the timer key’s LED will continue to flash..

If an alarm isn’t cancelled before the next timer expires, the alarm will sound continuously and both keys’ LED’s will flash.. The display will continue to show the first expired shelf timer number indicating the first shelf to be unloaded.. Cancel the displayed timer by pressing the corresponding shelf timer key once, then unload the shelf.. The display will indicate Shelf X, where X is the number of the next shelf to be unloaded.. Expired, uncanceled shelf timers will continue to be displayed in the order of their expiration as each previous timer is cancelled..

Display Messages

The display will be blank if the oven has been Off longer than 30 seconds..

This is the message that is displayed when the On/Off key is pushed and the unit is powering down.. This message is displayed for 30 seconds before going blank.. It is also displayed when the Auto Cool Down function shuts off..

This is a warning message shown when the oven cavity temperature exceeds the programmed temperature by more than 25ºF.. The actual temperature and programmed temperature are also displayed..

This is the warning message shown when the oven cavity temperature exceeds 575ºF.. All oven function is shut down and the user must remove power from the oven to reset the control after correcting the error.. The audible alarm will sound continuously..

If the control senses that the cavity probe shorts out or goes to an open circuit this message will be displayed and the audible alarm will sound continuously..

Part # MPSM07 (03/24/08)

Page 25

Image 25
Contents Models MP-GS/GD-10-S MPSM07 03/24/08 Table of Contents MPSM07 03/24/08 Section One Operation Installation Manual MPSM07 03/24/08 Inlet Hour Dimensions and SpecificationsLegs and Casters Preparing the Oven for InstallationInner Outer Open Base AssemblyItem Description Stacking Two OvensGAS Connections InstallationLocation Wall ClearanceElectrical Connections Water Quality Requirements Water ConnectionsSpray/Flex Hose W/Quick Disconnect DrainVentilation and AIR Supply Installation of a Direct VentTo Conserve Energy GAS Model Testing & Lighting InstructionsFan Speed Switch Moisture SwitchPower Switch Light SwitchStart Up Off ModeFan Speed Interior LightOn/Off DisplayLight MoistureHigh Fan Start/CancelLow Fan Pulse FanProgrammable Control Deluxe Models Changing the Temperature Scale, F or CStart-Up Auto Cool Down And Cool DownProgram Moisture Using Cook & HoldCooking With a Core Probe System Program Options Programming Recipe KeysTo program a recipe key To program shelf timers Using the Shelf Timer FeatureCooking With a Recipe Key Display Messages Cooking with shelf timersMPSM07 03/24/08 Page MPSM07 03/24/08 Cooking with Moisture User Moisture SettingsMechanical Control, Standard Models Programmable Control, Deluxe ModelsProduct Temp Moisture + Cooking GuideTime Deluxe Control Standard Control Kaiser Rolls Performance Recommendations About Moisture PresetsTemperature Calibration Problem Problems / SolutionsSolution Exterior Cleaning CleaningInterior Cleaning Fan Area CleaningMotor Care MaintenanceWater System Replacement Parts MPSM07 03/24/08 Section Two Service Moisture Control Mechanical Moisture Control Component IdentificationWater pressure check Deluxe Fast Panel Moisture ControlService Overview Cavity Temperature ControlsControl Compartment Ambient Temperature Spritzer Water InletSolid State control Heat Control Transformer Diagnostics Mode Diagnostic ProceduresDoor Switch Test Proper Door Switch ActivationControl Safety Features Temperature CalibrationFan Speed Test Heat TestDiagnostic Procedures Mechanical Control Testing & TroubleshootingFast Control OK? Key Ribbon Test Points Key Pad / Ribbon Connector Test PointsRelay Board Relay Board Component IdentificationRelay Relay Output Inputs Outputs Function Test Point Test PointsFan Motor And Blower Wheel Component ReadingsDual Stage Gas Valve Solenoid Resistance Direct Spark Ignition ModuleJohnson Controls INC ManufacturerWiringdiagrams Wiring Diagrams Oven Door Service Removal / Installation Service Procedures REMOVAL/REPLACEMENTOven Door Light Service / Removal Remove both screws.. do not Touch the Countersink Screw Oven Temperature Probe Service/RemovalDoor To Cavity Seal Adjustments RH Door Frame To Cavity Seal AdjustmentMPSM07 03/24/08 Section Three Parts List Moisture Plus GAS Electronic Deluxe Control Panel Gas Garland Parts IdentificationStandard Control Panel Description Quantity UP to From Standard Control Panel Mechanical ControlBurners & GAS Components Burner & Gas Components Moisture Plus GAS Interior Components Gas MPSM07 03/24/08 Moisture +Description QTY UP to From Door ComponentsMoisture + 1934501 Valve-regulator Plumbing Components GasMoisture Plus 1926501 Caster 4 Screw 1926502 Caster 4 With Brake Screw Main ExteriorWire Diagrams Wire Diagrams & HarnessesWire Harness ModelMPSM07 03/24/08 MPSM07 03/24/08 MPSM07 03/24/08

MP-GS, MP-GD-10-S specifications

The Garland MP-GD-10-S and MP-GS are innovative electric pizza ovens designed for commercial applications, particularly in restaurants, pizzerias, and cafes. These ovens combine advanced technology with user-friendly features to deliver high-quality pizza quickly and efficiently.

One of the standout features of the Garland MP-GD-10-S is its dual-deck design, allowing operators to prepare two separate pizzas at once. This is a significant advantage during peak hours, as it enhances productivity without compromising quality. The MP-GS model boasts a similar configuration, promoting efficient cooking while also providing versatility in menu offerings.

Both models are equipped with powerful heating elements that ensure rapid heat-up times and consistent cooking temperatures. This technology is crucial for achieving the perfect pizza crust, as it facilitates even heat distribution across the cooking surface. The ovens also feature adjustable temperature controls, allowing users to tailor the cooking environment according to specific recipes or customer preferences.

The Garland MP-GD-10-S and MP-GS come with durable stainless steel exteriors, which not only contribute to an appealing aesthetic but also ensure easy cleaning and maintenance. The removable crumb tray further simplifies the cleanup process, allowing operators to focus on their culinary creations rather than time-consuming maintenance tasks.

Another notable characteristic of these ovens is their user-friendly controls. The intuitive interface allows staff to operate the ovens with minimal training, reducing the likelihood of errors and enhancing overall efficiency in the kitchen. Additionally, both models utilize a reliable digital timer for precise cooking times, ensuring that each pizza is cooked to perfection.

In terms of safety, the Garland MP-GD-10-S and MP-GS are equipped with sturdy door hinges and double-walled construction, promoting temperature retention and preventing exterior overheating. This design not only enhances safety in the kitchen but also optimizes energy efficiency, making them economical choices for busy food establishments.

Overall, the Garland MP-GD-10-S and MP-GS are exceptional electric pizza ovens that embody cutting-edge technology and practical design. Their combination of productivity, user-friendliness, and durable construction makes them a valuable addition to any commercial kitchen, catering to the demands of fast-paced culinary environments while ensuring top-notch pizza quality. Whether for a bustling pizzeria or a cozy cafe, these ovens are tailored to meet the needs of today’s food service professionals.