McCulloch ZM3016 BF, 966564001 manual Choke Control, Refueling, Risk for burns if touched, Controls

Page 20
Choke Control

CONTROLS

Choke Control

The choke control is used for cold starts in order to provide the engine with a richer fuel mixture.

For cold starts the throttle should be pushed forward to the choke position.

WARNING!

Gasoline is highly flammable. Observe caution and fill the tank outdoors (see the safety instruction).

Refueling

Read the safety instructions before refueling. The machine has one fuel tank, just behind the seat. The tank volume is 3 gallons (11.4 liters).

Make sure the fuel cap is properly tightened and the cap gasket is not damaged.

The engine will run on a minimum of 85-octane unleaded gasoline (no oil mix). Environmentally adapted alkylate gasoline can be used. See also Technical Data concerning ethanol fuel. Methanol fuel is not allowed. Do not use E85 alcohol based fuel. Damage to engine and components may occur.

IMPORTANT INFORMATION

Experience indicates that alcohol blended fuels (called gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel the next season. See Storage Instructions for additional information. Never use engine or carburetor cleaners in the fuel tank or permanent damage may occur.

8077-007

Choke control

8058-086

Fuel tank

WARNING!

The engine and the exhaust system, become very hot during operation.

Risk for burns if touched.

Allow engine and exhaust system to cool at least two (2) minutes before refueling

WARNING!

Fill to bottom of filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

20

Image 20
Contents Operator Manual ZM3016 BFIn order to implement improvements, specifications and designs can be altered without prior notification Contents Page INTRODUCTION CongratulationsGeneral Driving and Transport on Public RoadsGood Service Manufacturing Numbersymbols and decals Xxxx xxxxxxxxxxxxxxxxxxxxx IMPORTANT INFORMATIONremove safety remove key beforeperforming any Whole bodySAFETY Safety InstructionsSAFETY INSTRUCTIONS COULD THIS CUTTING MACHINE IS CAPABLEAlways wear eye protection when operating machine Personal Safety Equipment Slope OperationChildren Safe Handling of Gasoline There is risk for burns if touchedGeneral Maintenance Use protective glasses for maintenance workUse protective goggles Transport Spark ArrestorCONTROLS Control Locations4.Reverse Steering Control Levers1.Forward 2.Neutral 3.Neutral slot, Neutral lock Throttle Control Ignition SwitchParking Brake Risk for burns if touched Choke ControlRefueling Fuel Shut Off Valve Mower Deck Lifting LeverTracking Always use the high position F to transportSeat Adjustment Lever Blade Control LeverManual Transport the engine stopped the ignition key removedoperation TrainingSteering To move forward and backwardBefore Starting Starting the EngineMove the throttle to the middle position operation Jumper cables To remove cables, reverse orderRunning Operating on Hills Mowing Tips Stopping the Engine operation MAINTENANCE Maintenance ScheduleCheck/adjust throttle cable Clean/replace the spark plugsCheck/adjust the mower deck Perform the 300-hourserviceBattery To clean battery and terminalsReplacing battery Always use two wrenches for the terminal screwsSafety System Tire PressuresTo replace deck belt V-beltsDeck Belt Belt installation Blade replacementEZT Belt Cutting BladesLeveling Deck Adjusting the Mower Deck1.Engage the parking brake Cleaning Removal and installation of caster wheelUse protective glasses when cleaning and washing Caster WheelsLUBRICATION GeneralFront Wheel Mount Front Wheel BearingsEngine Lubrication Steering Control ShaftsCause TROUBLESHOOTINGProblem The engine seems weak Winter Storage Servicestorage SCHEMATIC TECHNICAL DATA Torque SpecificationsHEX HEAD CAP SCREWS U.S. Standard HardwareTransmission ZM3016 BFEngine Overall dimensions RZ3019 BFEquipment ProductivityCE Requirements CONForMITY CERTIFICATESUSA Requirements SERVICE JOURNAL 25-HourService 50-HourService 100-HourService300-HourService At Least Once Each YearPage P/N 115 349327R1 03/19/10