McCulloch 966564001, ZM3016 BF manual Jumper cables, To remove cables, reverse order, operation

Page 27
Jumper cables

operation

Slowly push the choke control down when the engine has started.

Set the desired engine speed with the throttle. Allow the engine to run at a moderate speed, “half throttle” for 3-5 minutes before loading it to heavily. USE FULL THROTTLE WHEN MOWING (no choke).

WARNING!

Engine exhaust and certain vehicle components contain or emit chemicals considered to cause cancer, birth defects, or other reproductive system damage. The engine exhaust contains carbon monoxide, which is a odorless, colorless, poisonous gas. Do not use the machine in enclosed spaces.

WARNING!

Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See Battery in the Maintenance section.)

If jumper cables are used for emergency starting, follow this procedure:

Jumper cables

1.Connect each end of the RED cable to the POSITIVE (+) terminal on each battery, taking care not to short against chassis.

2.Connect one end of the BLACK cable to the NEGATIVE (-) terminal of the fully charged battery.

3.Connect the other end of the BLACK cable to a good CHASSIS GROUND on the mower with the discharged battery, away from the fuel tank and battery.

To remove cables, reverse order

1.Remove BLACK cable first from chassis and then from the fully charged battery.

2.Remove RED cable last from both batteries.

8058-122

Use full throttle when mowing

IMPORTANT INFORMATION

Your mower is equipped with a 12-volt negative grounded system. The other vehicle must also be a 12-volt negative grounded system. Do not use your mower to start other vehicles.

8011-642

Jumper cable connection

27

Image 27
Contents ZM3016 BF Operator ManualIn order to implement improvements, specifications and designs can be altered without prior notification Contents Page Driving and Transport on Public Roads INTRODUCTIONCongratulations GeneralManufacturing Number Good ServiceIMPORTANT INFORMATION symbols and decalsXxxx xxxxxx xxxxxxxxxxxxxxxWhole body remove safetyremove key before performing anyTHIS CUTTING MACHINE IS CAPABLE SAFETYSafety Instructions SAFETY INSTRUCTIONS COULDAlways wear eye protection when operating machine Slope Operation Personal Safety EquipmentChildren There is risk for burns if touched Safe Handling of GasolineUse protective glasses for maintenance work General MaintenanceUse protective goggles Spark Arrestor TransportControl Locations CONTROLSSteering Control Levers 1.Forward 2.Neutral 3.Neutral slot, Neutral lock4.Reverse Ignition Switch Parking BrakeThrottle Control Choke Control RefuelingRisk for burns if touched Always use the high position F to transport Fuel Shut Off ValveMower Deck Lifting Lever Trackingthe engine stopped the ignition key removed Seat Adjustment LeverBlade Control Lever Manual TransportTo move forward and backward operationTraining SteeringStarting the Engine Before StartingMove the throttle to the middle position IMPORTANT INFORMATION To remove cables, reverse order Jumper cablesRunning Operating on Hills Mowing Tips Stopping the Engine Manual Transport Maintenance Schedule MAINTENANCEPerform the 300-hourservice Check/adjust throttle cableClean/replace the spark plugs Check/adjust the mower deckAlways use two wrenches for the terminal screws BatteryTo clean battery and terminals Replacing batteryTire Pressures Safety SystemV-belts Deck BeltTo replace deck belt Cutting Blades Belt installationBlade replacement EZT BeltAdjusting the Mower Deck 1.Engage the parking brakeLeveling Deck Caster Wheels CleaningRemoval and installation of caster wheel Use protective glasses when cleaning and washingGeneral LUBRICATIONSteering Control Shafts Front Wheel MountFront Wheel Bearings Engine LubricationTROUBLESHOOTING ProblemCause The engine seems weak Service storageWinter Storage SCHEMATIC U.S. Standard Hardware TECHNICAL DATATorque Specifications HEX HEAD CAP SCREWSZM3016 BF EngineTransmission Productivity Overall dimensionsRZ3019 BF EquipmentCONForMITY CERTIFICATES USA RequirementsCE Requirements SERVICE JOURNAL 25-HourService 100-HourService 50-HourServiceAt Least Once Each Year 300-HourServicePage 03/19/10 P/N 115 349327R1