McCulloch 966564001 manual V-belts, Deck Belt, To replace deck belt, Maintenance, Parking Brake

Page 37

V-belts

MAINTENANCE

Parking Brake

Visually check that no damage is found on the lever, links, or switch belonging to the parking brake. Perform a standstill test and check that there is sufficient braking action.

To adjust the parking brake, contact the McCulloch service workshop.

WARNING!

Faulty adjustment can result in reduced braking ability and can cause an accident.

V-belts

Check every 100 hours of operation. Check for severe cracking and large nicks.

NOTE: The belt will show some small cracks in normal operation.

The belts are not adjustable. Replace belts if they begin to slip from wear.

Deck Belt

To replace deck belt

Deck belt removal.

1.Park on a level surface. Apply park brake.

2.Lower the deck to the lowest cutting position.

3.Disengage the clutch by sliding the blade control lever downwards.

4.Carefully lift the belt away from belt keepers and off deck pulleys and remove from deck.

5.Replace belt (refer to the belt routing decal on the deck) and re-engage clutch.

8050-005

Check for proper operation of parking brake

8058-074

Disengage clutch to replace deck belt

8058-071

Check deck belt for excessive wear

37

Image 37

Contents ZM3016 BF Operator ManualIn order to implement improvements, specifications and designs can be altered without prior notification Contents Page Congratulations INTRODUCTIONGeneral Driving and Transport on Public RoadsManufacturing Number Good ServiceXxxx xxxxxx symbols and decalsxxxxxxxxxxxxxxx IMPORTANT INFORMATIONremove key before remove safetyperforming any Whole bodySafety Instructions SAFETYSAFETY INSTRUCTIONS COULD THIS CUTTING MACHINE IS CAPABLEAlways wear eye protection when operating machine Slope Operation Personal Safety EquipmentChildren There is risk for burns if touched Safe Handling of GasolineUse protective glasses for maintenance work General MaintenanceUse protective goggles Spark Arrestor TransportControl Locations CONTROLS1.Forward 2.Neutral 3.Neutral slot, Neutral lock Steering Control Levers4.Reverse Parking Brake Ignition SwitchThrottle Control Refueling Choke ControlRisk for burns if touched Mower Deck Lifting Lever Fuel Shut Off ValveTracking Always use the high position F to transportBlade Control Lever Seat Adjustment LeverManual Transport the engine stopped the ignition key removedTraining operationSteering To move forward and backwardStarting the Engine Before StartingMove the throttle to the middle position IMPORTANT INFORMATION To remove cables, reverse order Jumper cablesRunning Operating on Hills Mowing Tips Stopping the Engine Manual Transport Maintenance Schedule MAINTENANCEClean/replace the spark plugs Check/adjust throttle cableCheck/adjust the mower deck Perform the 300-hourserviceTo clean battery and terminals BatteryReplacing battery Always use two wrenches for the terminal screwsTire Pressures Safety SystemDeck Belt V-beltsTo replace deck belt Blade replacement Belt installationEZT Belt Cutting Blades1.Engage the parking brake Adjusting the Mower DeckLeveling Deck Removal and installation of caster wheel CleaningUse protective glasses when cleaning and washing Caster WheelsGeneral LUBRICATIONFront Wheel Bearings Front Wheel MountEngine Lubrication Steering Control ShaftsProblem TROUBLESHOOTINGCause The engine seems weak storage ServiceWinter Storage SCHEMATIC Torque Specifications TECHNICAL DATAHEX HEAD CAP SCREWS U.S. Standard HardwareEngine ZM3016 BFTransmission RZ3019 BF Overall dimensionsEquipment ProductivityUSA Requirements CONForMITY CERTIFICATESCE Requirements SERVICE JOURNAL 25-HourService 100-HourService 50-HourServiceAt Least Once Each Year 300-HourServicePage 03/19/10 P/N 115 349327R1