McCulloch 966564001, ZM3016 BF manual Safety, Use protective goggles

Page 15
•Use protective goggles.

SAFETY

Sparking can occur when working with the battery and the heavy cables of the starter circuit. This can cause battery explosion, fire or eye injury. Sparking in this circuit can not occur after the chassis cable (normally negative, black) is removed from the battery.

Use protective goggles.

Ensure that the fuel filler cap is mounted tightly and no flammable substances are stored in an open vessel.

WARNING!

Avoid electrical sparking and its consequences by the following routines:

Never work with the starter circuit if there is spilled fuel.

Disconnect the negative cable from the battery first and reconnect it last.

Do not make a bridge short circuit across the starter relay to run the starter.

Never use the machine indoors or in spaces lacking proper ventilation. The exhaust fumes contain carbon monoxide, an odorless, poisonous, and lethal gas.

Stop to inspect the equipment if the machine runs over or into anything. If necessary, make repairs before starting.

Never make adjustments with the engine running.

The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer. Only use approved repair parts for the machine.

The blades are sharp and can cause cuts and gashes. Wrap the blades or use protective gloves when handling them.

Check the parking brake’s functionality regularly. Adjust and service as necessary.

The mulch blades should only be used in familiar areas when higher quality mowing is desired.

Reduce the risk of fire by removing grass, leaves, and other debris that may have accumulated on the machine.

Allow the machine to cool before putting it in storage.

Regularly clean deck and underside of deck, avoid spraying engine and electrical components with water.

6003-009

Do not smoke when performing maintenance on the battery. The battery can explode and cause serious injury/damage.

8009-728

Risk of sparking

8011-514

Regularly clean deck

15

Image 15
Contents ZM3016 BF Operator ManualIn order to implement improvements, specifications and designs can be altered without prior notification Contents Page Driving and Transport on Public Roads INTRODUCTIONCongratulations GeneralManufacturing Number Good ServiceIMPORTANT INFORMATION symbols and decalsXxxx xxxxxx xxxxxxxxxxxxxxxWhole body remove safetyremove key before performing anyTHIS CUTTING MACHINE IS CAPABLE SAFETYSafety Instructions SAFETY INSTRUCTIONS COULDAlways wear eye protection when operating machine Slope Operation Personal Safety EquipmentChildren There is risk for burns if touched Safe Handling of GasolineUse protective glasses for maintenance work General MaintenanceUse protective goggles Spark Arrestor TransportControl Locations CONTROLSSteering Control Levers 1.Forward 2.Neutral 3.Neutral slot, Neutral lock4.Reverse Ignition Switch Parking BrakeThrottle Control Choke Control RefuelingRisk for burns if touched Always use the high position F to transport Fuel Shut Off ValveMower Deck Lifting Lever Trackingthe engine stopped the ignition key removed Seat Adjustment LeverBlade Control Lever Manual TransportTo move forward and backward operationTraining SteeringStarting the Engine Before StartingMove the throttle to the middle position IMPORTANT INFORMATION To remove cables, reverse order Jumper cablesRunning Operating on Hills Mowing Tips Stopping the Engine Manual Transport Maintenance Schedule MAINTENANCEPerform the 300-hourservice Check/adjust throttle cableClean/replace the spark plugs Check/adjust the mower deckAlways use two wrenches for the terminal screws BatteryTo clean battery and terminals Replacing batteryTire Pressures Safety SystemV-belts Deck BeltTo replace deck belt Cutting Blades Belt installationBlade replacement EZT BeltAdjusting the Mower Deck 1.Engage the parking brakeLeveling Deck Caster Wheels CleaningRemoval and installation of caster wheel Use protective glasses when cleaning and washingGeneral LUBRICATIONSteering Control Shafts Front Wheel MountFront Wheel Bearings Engine LubricationTROUBLESHOOTING ProblemCause The engine seems weak Service storageWinter Storage SCHEMATIC U.S. Standard Hardware TECHNICAL DATATorque Specifications HEX HEAD CAP SCREWSZM3016 BF EngineTransmission Productivity Overall dimensionsRZ3019 BF EquipmentCONForMITY CERTIFICATES USA RequirementsCE Requirements SERVICE JOURNAL 25-HourService 100-HourService 50-HourServiceAt Least Once Each Year 300-HourServicePage 03/19/10 P/N 115 349327R1