McCulloch ZM3016 BF, 966564001 manual Engine, Transmission, Technical Data

Page 48

	TECHNICAL DATA


	ZM3016 BF / 966564001

Engine

Manufacturer	Briggs & Stratton 1)

Type	Endurance

Power	16.5 hp 2)

Lubrication	Pressure with oil filter

Fuel	Min 86 octane unleaded (Maxethanol 5%, Max MTBE 15%)

Fuel tank capacity	3 gallons / 11.3 liters
Cooling	Air cooled

Air filter	Standard

Alternator	12V / 16A

Starter	Electric 12V

Transmission

Transmission	EZT Hydro Gear
Speed and direction controls	Dual levers, foam gripped

Speed forward	5.8 mph / 9.3 km/h

Speed reverse	3.3 mph / 5.3 km/h

Brakes	Mechanical parking brake

Front caster tires, smooth tread	410-5, 4 ply

Rear tires, turf pneumatic	18 x 6.5-8
Tire pressure	15 PSI / 103 kPa / 1 bar

1)Refer to the engine manufacturer's Owner's Manual for engine specifications.

2)The power rating of the engines indicated is the average net power output (at specified rpm) of a typical production engine for the engine model measured to SAE standard J1349/ISO1585. Mass production engines may differ from this value. Actual power output for the engine installed in the final machine will depend on the operating speed, environmental conditions and other variables.

48

Image 48

Contents Operator Manual ZM3016 BFIn order to implement improvements, specifications and designs can be altered without prior notification Contents Page INTRODUCTION CongratulationsGeneral Driving and Transport on Public RoadsGood Service Manufacturing Numbersymbols and decals Xxxx xxxxxxxxxxxxxxxxxxxxx IMPORTANT INFORMATIONremove safety remove key beforeperforming any Whole bodySAFETY Safety InstructionsSAFETY INSTRUCTIONS COULD THIS CUTTING MACHINE IS CAPABLEAlways wear eye protection when operating machine Personal Safety Equipment Slope OperationChildren Safe Handling of Gasoline There is risk for burns if touchedGeneral Maintenance Use protective glasses for maintenance workUse protective goggles Transport Spark ArrestorCONTROLS Control LocationsSteering Control Levers 1.Forward 2.Neutral 3.Neutral slot, Neutral lock4.Reverse Ignition Switch Parking BrakeThrottle Control Choke Control RefuelingRisk for burns if touched Fuel Shut Off Valve Mower Deck Lifting LeverTracking Always use the high position F to transportSeat Adjustment Lever Blade Control LeverManual Transport the engine stopped the ignition key removedoperation TrainingSteering To move forward and backwardBefore Starting Starting the EngineMove the throttle to the middle position operation Jumper cables To remove cables, reverse orderRunning Operating on Hills Mowing Tips Stopping the Engine operation MAINTENANCE Maintenance ScheduleCheck/adjust throttle cable Clean/replace the spark plugsCheck/adjust the mower deck Perform the 300-hourserviceBattery To clean battery and terminalsReplacing battery Always use two wrenches for the terminal screwsSafety System Tire PressuresV-belts Deck BeltTo replace deck belt Belt installation Blade replacementEZT Belt Cutting BladesAdjusting the Mower Deck 1.Engage the parking brakeLeveling Deck Cleaning Removal and installation of caster wheelUse protective glasses when cleaning and washing Caster WheelsLUBRICATION GeneralFront Wheel Mount Front Wheel BearingsEngine Lubrication Steering Control ShaftsTROUBLESHOOTING ProblemCause The engine seems weak Service storageWinter Storage SCHEMATIC TECHNICAL DATA Torque SpecificationsHEX HEAD CAP SCREWS U.S. Standard HardwareZM3016 BF EngineTransmission Overall dimensions RZ3019 BFEquipment ProductivityCONForMITY CERTIFICATES USA RequirementsCE Requirements SERVICE JOURNAL 25-HourService 50-HourService 100-HourService300-HourService At Least Once Each YearPage P/N 115 349327R1 03/19/10