McCulloch 966564001 manual Battery, To clean battery and terminals, Replacing battery, Maintenance

Page 35
Battery

MAINTENANCE

Battery

Your mower is equipped with a maintenance free battery that does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

Recharge at 6-10 amperes for 1 hour

To clean battery and terminals

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

1.Open the terminal access doors.

2.Remove the red terminal guard.

3.Disconnect BLACK battery cable first, then the RED battery cable and remove the battery from the machine.

4.Rinse the battery with plain water and dry.

5.Clean terminals and battery cable ends with wire brush until shiny.

6.Coat terminals with grease or petroleum jelly

7.Reinstall battery.

IMPORTANT INFORMATION

Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

Always use two wrenches for the terminal screws.

Replacing battery

1.Lift seat and rotate forward.

2.Remove the terminal guard.

3.Using two ½" wrenches disconnect BLACK battery cable then RED battery cable.

4.Unscrew the knob and remove battery hold down.

5.Carefully remove the battery from the mower.

6.Install new battery with terminals in the same position as the old battery.

7.Reinstall battery hold down.

8.First connect RED battery cable to positive (+) battery terminal with hex bolt and hex nut.

9.Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and hex nut.

10.Fit the terminal guard.

11.Lower seat.

To clean battery and terminals Always use protective glasses when handling the battery.

STANDARD

STATE

APPROXIMATE BATTERY CHARGING TIME*

 

 

TO FULL CHARGE AT 80OF / 27OC

BATTERY

OF

 

 

 

 

 

Maximum Rate at:

 

 

 

 

 

 

CHARGE

 

 

 

 

 

50 Amps

30 Amps

20 Amps

10 Amps

 

 

 

 

 

 

 

 

12.6V

100%

- FULL CHARGE -

 

 

 

 

 

 

12.4V

75%

20 min.

35 min.

48 min.

90 min.

 

 

 

 

 

 

12.2V

50%

45 min.

75 min.

95 min.

180 min.

 

 

 

 

 

 

12.0V

25%

65 min.

115 min.

145 min.

280 min.

 

 

 

 

 

 

11.8V

0%

85 min.

150 min.

195 min.

370 min.

 

 

 

 

 

 

*Charging time depends on battery capacity,

condition, age, temperature and efficiency of charger

WARNING!

Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparks from accidental grounding.

8050-109

Battery cleaning and installation

35

Image 35
Contents ZM3016 BF Operator ManualIn order to implement improvements, specifications and designs can be altered without prior notification Contents Page Driving and Transport on Public Roads INTRODUCTIONCongratulations GeneralManufacturing Number Good ServiceIMPORTANT INFORMATION symbols and decalsXxxx xxxxxx xxxxxxxxxxxxxxxWhole body remove safetyremove key before performing anyTHIS CUTTING MACHINE IS CAPABLE SAFETYSafety Instructions SAFETY INSTRUCTIONS COULDAlways wear eye protection when operating machine Slope Operation Personal Safety EquipmentChildren There is risk for burns if touched Safe Handling of GasolineUse protective glasses for maintenance work General MaintenanceUse protective goggles Spark Arrestor TransportControl Locations CONTROLS4.Reverse Steering Control Levers1.Forward 2.Neutral 3.Neutral slot, Neutral lock Throttle Control Ignition SwitchParking Brake Risk for burns if touched Choke ControlRefueling Always use the high position F to transport Fuel Shut Off ValveMower Deck Lifting Lever Trackingthe engine stopped the ignition key removed Seat Adjustment LeverBlade Control Lever Manual TransportTo move forward and backward operationTraining SteeringStarting the Engine Before StartingMove the throttle to the middle position IMPORTANT INFORMATION To remove cables, reverse order Jumper cablesRunning Operating on Hills Mowing Tips Stopping the Engine Manual Transport Maintenance Schedule MAINTENANCEPerform the 300-hourservice Check/adjust throttle cableClean/replace the spark plugs Check/adjust the mower deckAlways use two wrenches for the terminal screws BatteryTo clean battery and terminals Replacing batteryTire Pressures Safety SystemTo replace deck belt V-beltsDeck Belt Cutting Blades Belt installationBlade replacement EZT BeltLeveling Deck Adjusting the Mower Deck1.Engage the parking brake Caster Wheels CleaningRemoval and installation of caster wheel Use protective glasses when cleaning and washingGeneral LUBRICATIONSteering Control Shafts Front Wheel MountFront Wheel Bearings Engine LubricationCause TROUBLESHOOTINGProblem The engine seems weak Winter Storage Servicestorage SCHEMATIC U.S. Standard Hardware TECHNICAL DATATorque Specifications HEX HEAD CAP SCREWSTransmission ZM3016 BFEngine Productivity Overall dimensionsRZ3019 BF EquipmentCE Requirements CONForMITY CERTIFICATESUSA Requirements SERVICE JOURNAL 25-HourService 100-HourService 50-HourServiceAt Least Once Each Year 300-HourServicePage 03/19/10 P/N 115 349327R1