Homelite UT43103 Tronçonnage Avec Coins, Débitage DE Billes Sous Contrainte, Coupe PAR LE Dessus

Page 49

UTILISATION

n Lors du tronçonnage sur une pente, toujours se tenir en amont de la bille. En fin de coupe, réduire la pression exercée sur la scie, sans relâcher la prise des deux mains sur les poignées afin de garder le contrôle de la scie. Ne pas laisser la chaîne heurter le sol. Une fois la coupe terminée, attendre l’immobilisation complète de la chaîne avant de se déplacer. Toujours arrêter le moteur avant de passer d’un arbre à un autre.

TRONÇONNAGE AVEC COINS

Voir la figure 19.

Si le diamètre de la pièce est assez grand pour permettre l’insertion d’un coin en bois tendre sans que celui-ci touche la chaîne, utiliser le coin pour maintenir l’entaille ouverte et empêcher le pincement de la chaîne.

NOTE : Lorsque des coins sont utilisés pour l’entaille ou l’abattage, il peut être nécessaire de retirer la garde antirebond SAFE-T-TIP afin de pouvoir tirer la lame au travers de la section. Une fois la coupe effectuée, remettre la garde en place.

DÉBITAGE DE BILLES SOUS

CONTRAINTE

Voir la figure 20.

Pratiquer la première entaille à 1/3 du diamètre de la pièce et finir la coupe des 2/3 restant depuis le côté opposé. À mesure qu’elle est coupée, la bille a tendance

àployer. Si la première coupe dépasse le tiers du diamètre de la bille, la lame risque d’être pincée ou bloquée dans l’entaille.

Prêter une attention particulière aux billes sous contrainte pour éviter que le guide et la chaîne ne soient pincés.

COUPE PAR LE DESSUS

Voir la figure 21.

Commencer sur le haut de la bille, le bas de la scie appuyé contre le bois et exercer une légère pression vers le bas. Noter que la scie aura tendance à tirer vers l’avant.

COIN

Fig. 19

BILLE SOUTENUE À UNE EXTRÉMITÉ

COUPE DE

FINITION CHARGE

1ÈRE COUPE 1/3 DIAM

BILLE SOUTENUE AUX DEUX EXTRÉMITÉS

1ÈRE COUPE 1/3 DIAM CHARGE

COUPE DE FINITION Fig. 20

COUPE PAR LE DESSUS

Fig. 21

Page 19 — Français

Image 49
Contents Save this Manual for Future Reference Manuel D’UTILISATION Manual DEL OperadorALL Versions Toutes LES Versions Todas LAS Versiones Introduction Table of ContentsRead ALL Instructions Basic Safety Precautions General Safety Rules4 English See Figures 1 KickbackRotational Kickback SAFE-T-TIPANTI-KICKBACK Nose Guard Understanding Your Chain SAW Safety DevicesLOW Kickback SAW Chain Guide BarsSymbol Signal Meaning Symbols8 English Double Insulation FeatureselectricalElectrical Connection Extension CordsBar Tip Guard Glossary of TermsProduct Specifications FeaturesSwitch LOCK-OUT ­Assembly Applications OperationAdding BAR and Chain Lubricant OIL Reservoir CAPSwitch LOCK-OUT ­ Connecting to Power SupplyStarting and Stopping the Chain SAW Preparing for Cutting Proper Grip on HandlesProper Hand Grip Position Proper Grip Proper Cutting StanceChain Line Proper Procedure for Tree Felling Work Area PrecautionsFelling Trees Hazardous Conditions See Figures 13Hinge Planned Line FallNotch Approx /3 Diameter Trunk Bucking Removing Buttress RootsHinge Back CUT Wedge Vertical Loose Section Bucking Logs Under Stress Bucking with a WedgeOverbucking Wedge LOG Supported AT ONE END Finishing CUTLimbing UnderbuckingPruning Limbs Under Tree Until LOG is CUT SpringpoleCutting Springpoles General Maintenance MaintenanceLubrication Replacing the Guide BAR and ChainCover ≈ .050 Flats on Drive LinksChain Maintenance Adjusting the Chain TensionSee Figures 34 See Figures 36See Figures 38 Sharpening the CuttersSide Plate Angle TOP Plate Filing AngleMaintaining Depth Gauge Clearance SeeMounting the SAFE-T-TIPNOSE Guard Maintaining the Guide BARMaintaining the SAFE-T-TIPNOSE Guard See Figures 48Storing the Product BAR and Chain Combinations TroubleshootingLimited Warranty Statement WarrantyPage AVERTISSEMENT  Règles DE Sécurité GénéralesRègles DE Sécurité Générales Rebond AvertissementChaîne À Rebond Réduit Garde Antirebond SAFE-T-TIPGuides Voir la figureSymbole Signal Signification SymbolesNOM Désignation / Explication Isolation Double CaractéristiquesfonctionsélectriquesConnexion Électrique Cordons ProlongateursProtection de nez de guide GlossaireSpécifications CaractéristiquesGâchette ­ CordonAssemblage Appoint D’HUILE Pour Guide ET Chaîne UtilisationDémarrage ET Arrêt DE LA Scie À Chaîne Branchement SUR UNE Prise SecteurVerrouillage DU COMMUTATEUR­ Gâchette ­ Prise Correcte Position DE Coupe CorrectePrécautions À Prendre SUR LE Lieu DE Travail Méthodes D’UTILISATION / Coupe ÉlémentairesAbattage D’ARBRES Situations Dangereuses AVERTISSEMENT  Ligne DE Chute Prévue Méthode Correcte D’ABATTAGEOU 1/10 ÈME DU Diamètre Débitage Élimination DES Racines ÉchassesTrait ’ABATTAGE Charnière Coin Coupe Verticale Section Coupée Horizontale RebondDébitage DE Billes Sous Contrainte Tronçonnage Avec CoinsCoupe PAR LE Dessus Coupe PAR LE DessusÉbranchage Coupe PAR LE DessousÉlagage CELUI-CI Soit Débité FouetCoupe DE Fouets Entretien Remplacement DU Guide ET DE LA ChaîneEntretien Général LubrificationMaillons D’ENTRAÎNEMENT Rainure DU Guide Dents24 Français Entretien DE LA Chaîne Réglage DE LA Tension DE ChaîneVoir les figures 34 et Voir les figures 36 etVoir les figures 38 à Affûtage DES DentsTalonnage Sabot Creux Angle DE Plaque Latérale Angle D’AFFÛTAGE DE LA Plaque SupérieureDents DE Gauche Droite Crochet Angle Arrière IncorrectMaintien DU JEU DU Limiteur DE Profondeur Installation DE LA Garde SAFE-T- TIPEntretien DU Guide Voir les figures 44 àRemisage LE Produit Entretien DE LA Garde SAFE-T-TIPVoir les figures 47 et VIS DE Montage SAFE-T-TIPDépannage Combinaisons DE Guide ET ChaîneDéclaration DE Garantie Limitée GarantieAdvertencia Reglas DE Seguridad GeneralesPágina 4 Español Contragolpe Rotatorio ContragolpeZona DE Peligro DE Contragolpe Barras Guía SAFE-T-TIPDE LA PuntaTirón Empuje SAFE-T-TIP Símbolo Señal Significado Peligro SímbolosNombre Denominación / Explicación Doble Aislamiento AspectosfeatureseléctricosConexión Eléctrica Cordones DE ExtensiónProtección de la punta de la barra Glosario DE TérminosEspecificaciones DEL Producto CaracterísticasDE Lubricante Mango Trasero Armado Abastecimiento DE Lubricante Para LA Barra Y LA Cadena FuncionamientoAplicaciones Encendido Y Apagado DE LA Motosierra Conexión AL Suministro DE CorrientePreparación Para EL Corte Sujeción Correcta DE LOS Mangos Procedimientos Básicos DE Funcionamiento Y Corte Postura Correcta Para EL CorteTala DE Árboles Condiciones Peligrosas Advertencia Precauciones Relacionadas CON EL Área DE TrabajoProcedimiento Correcto Para Talar Árboles Segura Línea Planeada DE CaídaMuesca Diámetro DEL TroncoTronzado Eliminación DE Raíces ZancasCorte Bisagra Cuña Corte Vertical Parte Suelta Horizontal ContragolpeTronzado DE Troncos Bajo Tensión Tronzado CON CuñaTronzado POR Arriba Cuña Tronco Apoyado POR UN Extremo Corte FinalDesramado Tronzado POR AbajoPoda Corte DE Pértigas Mantenimiento General MantenimientoCómo Reemplazar LA Barra Guía Y LA Cadena LubricaciónPrecaución Advertencia Página 24 Español Precaución Ajuste DE LA Tensión DE LA CadenaMantenimiento DE LA Cadena Vea las figuras 34 yVea las figuras 38 a Afilado DE LOS Dientes DE CorteÁngulo DE LA Placa Lateral Ángulo DE Limadura DE LA Placa SuperiorDientes DE Corte Izquierdos Forma IncorrectaCalibres DE Profundidad Mantenimiento DE LA Barra GuíaAlmacenamiento DE LA Producto Montaje DE LA Protección SAFE- T-TIP DE LA PuntaTornillo DE Montaje SAFE-T-TIP Apriételo Vuelta Combinaciones DE Barra Y Cadena Solución DE ProblemasDeclaración DE LA Garantía Limitada GarantíaPage Manuel D’UTILISATION Manual DEL Operador OPERATOR’S ManualHomelite Consumer PRODUCTS, INC

UT43103 specifications

The Homelite UT43103 is a robust and versatile electric string trimmer designed to tackle a variety of yard care tasks. With its user-friendly features and efficient performance, this trimmer is ideal for homeowners seeking a reliable solution for maintaining their lawns, gardens, and hard-to-reach areas.

One of the standout features of the UT43103 is its powerful 13-amp motor, which delivers impressive cutting performance. This motor enables the trimmer to handle tough overgrown weeds and grass with ease, ensuring that users can achieve a clean and polished look in their outdoor spaces. The trimmer is also equipped with a 17-inch cutting width, allowing for wider paths with each pass, which enhances productivity and reduces the time spent on lawn care.

The Homelite UT43103 incorporates a lightweight design that makes it easy to maneuver, even during extended use. Weighing just a fraction of many gas-powered models, this electric trimmer minimizes user fatigue, making it an excellent choice for those with larger yards or multiple areas that require attention. Additionally, the adjustable handle provides custom comfort and control, allowing for easier navigation around plants and obstacles.

This trimmer features a convenient automatic feed spool system, which ensures a continuous supply of trimmer line without the need for manual adjustments. This technology not only maximizes efficiency but also enhances the user experience by reducing interruptions during work. Furthermore, the trimmer is compatible with various types of line and attachments, allowing users to customize their equipment based on specific lawn care needs.

Durability is another characteristic of the Homelite UT43103. Constructed with high-quality materials, this trimmer is built to withstand regular use while maintaining its performance. The trimmer also features a robust guard that protects the user from debris while trimming, enhancing safety during operation.

In summary, the Homelite UT43103 electric string trimmer is an excellent choice for homeowners looking for a powerful, reliable, and easy-to-use tool for yard maintenance. With its efficient motor, automatic feed spool, lightweight design, and durable construction, this trimmer stands out as a commendable solution for achieving a well-groomed lawn with minimal effort. Whether tackling overgrown weeds or fine-tuning edges, the UT43103 makes lawn care accessible and efficient.