Guardian Technologies 004270-3 owner manual Cleaning the Generator, Battery Maintenance

Page 15

Section 3 – Maintenance

QUIETPACT™ 75D Recreational Vehicle Generator

Be sure to reinstall the hex pipe cap tightly to the spark arrestor cleanout pipe. Vibration could cause a loose cap to fall out, resulting in hot engine exhaust being drawn through the centrifugal cooling fan and out beneath the unit. This could result in damage to the genera- tor or in discharge of hot exhaust sparks beneath the unit.

Figure 3.3 – Spark Arrestor

Muffler Maintenance

3/8" NPT HEX PIPE CAP

GASKET

ACCESS PLATE

3.5CLEANING THE GENERATOR

Keep the generator as clean and as dry as possible. Dirt and moisture that accumulate on internal gener- ator windings have adversely affect insulation resis- tance.

Periodically, clean the generator’s exterior surfaces. A soft brush may be used to loosen caked-on dirt. Use a vacuum system or dry, low-pressure air to remove any accumulations of dirt. The generator is housed inside an all-weather enclosure; clean the enclosure with a soft, damp cloth or with sponge and water.

Once each year, have the generator cleaned and inspected by a Generac Authorized Service Dealer. Service technicians will use dry, low-pressure air to clean internal windings. Parts inside the control con- sole should be cleaned and inspected at this time, as well.

Finally, have the insulation resistance of stator and rotor windings checked. If insulation resistances are excessively low, the generator may require drying.

Do NOT use a forceful spray of water to clean

!the generator. Water will enter the generator interior and cause problems, and may also contaminate the generator fuel system.

3.6BATTERY MAINTENANCE

All lead-acid batteries will discharge when not in use. The generator battery should be inspected per the “Service Schedule,” Section 3.13. The following pro- cedure should be used for inspection:

Inspect the battery posts and cables for tightness and corrosion. Tighten and clean as necessary.

Check the battery fluid level of unsealed batteries and, if necessary, fill with Distilled Water Only. Do not use tap water in batteries.

Have the state of charge and condition checked by a Generac Authorized Service Dealer.

NOTE:

Servicing of the battery is to be performed or supervised by knowledgeable personnel, accord- ing to the required precautions. Keep unautho- rized personnel away from batteries.

Damage will result if the battery connections are made in reverse.

DANGER

Do not dispose of the battery in a fire. The battery is capable of exploding. Storage batter- ies release explosive hydrogen gas. This gas can form an explosive mixture around the battery for several hours after charging. The slightest spark can ignite the gas and cause an explo- sion. Such an explosion can shatter the battery and cause blindness or other injury. Any area that houses a storage battery must be properly ventilated. Do not allow smoking, open flame, sparks, or any spark-producing tool or equip- ment near the battery. Discharge static electrici- ty from body before touching the battery by first touching a grounded metal surface.

A battery presents a risk of electrical shock and high short-circuit current. The following precau- tions are to be observed when working on bat- teries:

Remove watches, rings, and other metal objects;

Use tools with insulated handles;

Wear rubber gloves and boots;

Do not lay tools or metal parts on top of the battery;

Disconnect any charging source prior to connect- ing, or disconnecting, battery terminals; and

Do not use any jumper cables or booster battery to crank and start the generator engine. If any bat- tery has discharged, remove it for recharging.

Generac® Power Systems, Inc. 13

Image 15
Contents Liquid-cooled Recreational Vehicle Generator Introduction Authorized Service Dealer LocationTable of Contents Part II Installation InstructionsGeneral Hazards Electrical Hazards Generator Identification ModelQuietpact 75D Generator AC Connection System SafetySpecifications Generator ApplicabilityEngine Fuel Consumption GAL/HREngine OIL Requirements CoolantGenerator Control Panel Optional Remote START/STOPBefore Starting the Engine Starting the Generator Protection Systems Stopping the Generator1 25-HOUR BREAK-IN Period Additional InformationOverspeed Shutdown Overvoltage ProtectionEffects of Moisture and Dirt Checking the Engine OIL LevelChanging the Engine OIL AND/OR OIL Filter Operation in High Grass or BrushSpark Arrestor Muffler Servicing the Engine AIR FilterBattery Maintenance Cleaning the GeneratorExercising the Generator Cooling SystemEngine Coolant Drive BeltOUT-OF-SERVICE Procedure Removal from ServiceReturn to Service Service Schedule Part General Hazards Fire Hazards Generator Engine Operating Speed Purpose and Scope ManualStandards Booklets Equipment DescriptionMajor Features and Dimensions Suspended Mounting Location and SupportGenerator Location Generator SupportGenerator Compartments Generator RestraintCompartment Construction Acoustics Sound Insulating MaterialsTypical Noise Abatement 2.2.4 Compartment Floor Cutouts Cooling and Ventilating AIR Cooling AIR Inlet OpeningsGenerator Airflow Testing the Installation Diesel Fuel SystemCompensating for Restrictions Fuel Tank Generator Fuel Supply LinesGenerator Fuel Return Lines Exhaust System Safety Exhaust SystemMuffler and Spark Arrestor Generator AC Connections WiringElectrical Connections Electrical Junction BOXVolts Only Dual Circuits Generator Coversion toPower Supply Cord Isolating Different Power SourcesConduit Battery Cable Connections Battery InstallationRecommended Battery Battery CablesOptional Accessories Battery CompartmentRemote START/STOP Connections Initial Start Post Installation TestsTesting Under Load Before Initial StartupInstallation Checklist Problem Cause Correction Troubleshooting GuideAppendix 2 Notes Appendix 2 Notes Appendix 3 Electrical Data Appendix 3 Electrical Data Appendix 3 Electrical Data Wiring Diagram 120 VAC- Drawing No. 0D2793-B Part Part NO. QTY Description 677mm Frame Control Panel Refer to Drawing Hose, ¾ SAE-20R3 Gasket, Electrical Enclosure Divider To Engine AIR Intake 0C6946A Fuel Pump Assembly 023484F Snap Bushing 052219 1917 2118 11 29 32 33 QTY Description Complete Cylinder Block Cylinder Head Assembly Complete Crankshaft Idler Gear Assembly Rocker ARM Assembly Injection Pump Assembly Fuel Filter HOUSING, Timing Gear OIL PAN 1413 Appendix 5 Notes Parts Covered Federal and California Emissions Control Warranty StatementYour Warranty Rights and Obligations Manufacturers Warranty CoverageObtaining Warranty Service Obligations and Rights of the Manufacturer and OwnerLimitations Warranty Schedule CONSUMER/PERSONAL Applications