Husqvarna Rider 155 manual Maintenance schedule, Daily Maintenance interval, Hours, 100 200

Page 25

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance which should be conducted on the machine. For the items which are not described in these instructions go to an authorised service workshop.

 

 

Daily

Maintenance interval

Maintenance

Page

maintenance

 

in hours

 

before start

 

 

 

 

 

 

25

50

100

200

 

 

 

 

 

 

 

 

 

 

 

 

Check the engine’s oil level

41

 

 

 

 

Check the engine’s cooling air inlet

30

 

 

 

 

Check the steering wires

25

 

 

 

 

Check the safety system

29

 

 

 

 

Check screws and nuts

 

 

 

 

Check for fuel and oil leakage

 

 

 

 

Clean around the silencer

 

 

 

 

Clean the air filter’s prefilter 2)

27

 

 

 

 

 

Check the cutting unit

33

 

 

 

 

 

Check the tyre pressures 60 kPa/8.5 PSI

30

 

 

 

 

 

Lubricating the belt adjuster 3)

42

 

 

 

 

 

Lubricate joints and shafts 3)

42

 

 

 

 

 

Check the V-belts

 

 

 

 

 

Check the hydrostat’s cooling fins

 

 

 

 

 

Check the transmission’s oil level

42

 

 

 

 

 

Adjust the brakes

25

 

 

 

 

 

Check and adjust the throttle wire

26

 

 

 

 

 

Change the engine oil 1)

41

 

 

 

1)

1)

 

Clean the engine’s and hydrostat’s cooling flanges 2,4)

 

 

 

 

 

Replace the air filter’s paper filter 2)

27

 

 

 

 

 

Replace the fuel filter

26

 

 

 

 

 

Clean or replace the spark plug

28

 

 

 

 

 

Replace the oil filter

42

 

 

 

 

 

 

 

 

 

 

 

 

 

1)First change after 5 hours. Replace after every 50 hours with heavy loads or high temperatures. 2)During dusty conditions cleaning and replacement should be more frequent. 3)For daily use of the machine lubrication should be conducted twice a week. 4)Conducted by authorised service workshop.

= Described in these instructions.

= Not described in these instructions.

WARNING!

No service procedures must be conducted on the engine or cutting unit unless:

The engine is switched off.

The parking brake is applied.

The ignition key is removed.

The cutting unit is disengaged.

The ignition cable is removed from the plug.

English – 23

Image 25
Contents English RiderSvenska Contents General operation Safe operation practices for ride-on mowersII. Slope operation III. ChildrenTravel and transport on public roads IV. ServiceTowing Intended useDear customer IntroductionTravel and transport on public roads TowingSerial number Good serviceStarting Instruction Explanation of SymbolsPlacards General use Safety InstructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Speed limiter Throttle and Choke leverParking brake Lift lever for cutting unit Cutting unitSeat Lever for adjustment of cutting heightFuelling Before starting DrivingStarting the engine Cold engineWarm engine Driving the machine Cutting tips Release lever Stopping the engineMaintenance schedule MaintenanceDaily Maintenance interval HoursEngine hood Removal of the machine hoodsFront hood Right-hand fenderAdjusting the brake Checking and adjustment of the steering wiresPoorly adjusted brakes can result in reduced braking power Replacement of the fuel filter Adjusting the throttle wireService of the air filter Ignition system BatteryFitting the wrong spark plug type can damage the engine Inspecting the safety system Checking the tyre pressure Main fuseCheck the engine’s cooling air intake Observe caution to avoid trapping your hand Fitting the cutting unitRemoving the cutting unit 6017-216 Checking the cutting unit’s parallelism Adjusting the parallelism of the cutting unitReplacing the cutting unit belt Placing in service position Service position for cutting unit6017-221 6017-222 8009-122 6017-223 Restoring from service position Checking the blades Removal of BioClip plug Combi Replacing the break-pinCheck the engine’s oil level LubricationChanging the oil Dip stick must not be screwed downChange of oil filter Lubricating the belt adjusterCheck the transmission’s oil level General lubricationProblem Procedure Trouble Shooting ScheduleStorage ServiceWinter storage CoverTechnical Data Work done Date, mileage, stamp, sign Service JournalService Journal ´+H-¶5c¨ English 114 01