Husqvarna 210 C manual Trouble shooting, Fault messages

Page 40

8. TROUBLE SHOOTING

8. Trouble shooting

8.1 Fault messages

A number of fault messages that can be shown by the red Fault indicator lamp on Husqvarna Automower™ are shown below. The fault message is interpreted by reading how the lamp flashes. The lamp flashes one to five times in quick succession and then goes out for 2 seconds. This sequence is repeated until the Cancel button is pressed. For example, three flashes in the table below corresponds to the lamp flashing three times in quick succession, and then going out.

Always try to restart the mower if the Fault indicator lamp is lit or flashes. Restart the mower by pressing the Cancel button, enter your PIN code and close the cover

If the same fault occurs frequently, or if the Fault indicator lamp is lit with a steady light: contact your dealer.

Flashes

Fault message

Cause

Action

 

 

 

 

 

 

 

 

1

Wrong PIN code

Wrong PIN code has been

Enter the correct PIN code.

 

 

entered. Three attempts are

 

 

 

permitted, the keypad is then

 

 

 

blocked for five minutes.

 

 

 

 

 

1

Charger cable not

The charger cable is not

Connect the charger cable

 

connected

connected when changing the

 

 

 

PIN code, or when connecting

 

 

 

the mower to the loop

 

 

 

generator/charger.

 

 

 

 

 

2

No loop signal

The loop generator/charger is

Check the wall socket connection and

 

 

not connected to the mains

whether the miniature circuit-breaker has

 

 

supply or its miniature

tripped.

 

 

circuit-breaker has tripped.

Reset the miniature circuit-breaker by

 

 

 

removing the loop generator/charger's power

 

 

 

cord from the wall socket, wait 10 seconds

 

 

 

and then reconnect the power cord in the

 

 

 

wall socket again.

 

 

 

 

 

 

Boundary wire broken.

Check the signal given by the LED on the

 

 

 

loop generator/charger. If it flashes the loop

 

 

 

is damaged. Repair the broken cable using

 

 

 

an original waterproof coupler.

 

 

 

 

 

 

The connection between

Link the mower to the loop

 

 

Automower and the charging

generator/charger by changing the PIN

 

 

station has been lost.

code, see page 30. You can use the same

 

 

 

PIN code as earlier. You can use the same

 

 

 

PIN code as earlier.

 

 

 

 

 

 

This may be due to the

Check that the boundary wire has been

 

 

boundary wire being routed in

routed correctly.

 

 

the wrong direction around an

 

 

 

”island”, which blanks out the

 

 

 

signal.

 

 

 

 

 

 

 

If this occurs in isolated areas

Try moving the boundary wire.

 

 

it may be due to interference

 

 

 

from metallic objects

 

 

 

(perimeter fence,

 

 

 

reinforcement bar) or buried

 

 

 

cables in the vicinity.

 

 

 

 

 

3

No drive

Automower has got caught in

Free the mower and rectify the reason for

 

 

something.

the lack of drive. If it is due to wet grass, wait

 

 

 

until the lawn has dried before using the

 

 

 

mower.

 

 

 

 

English - 41

Image 40
Contents Husqvarna Automower 210 C OPERATOR’S Manual Table of Contents Table of Contents Introduction Safety IntroductionSymbols on Automower Symbols in the Operator’s Manual Safety instructions UseMaintenance TransportPresentation Automower, what’s what? Numbers in the picture correspond toCapacity Function of AutomowerMowing technique 3012-422 Working method One Automower in several gardens Movement patternInstallation Carry out the installation in the following stepsInstallation of the loop generator/charger PreparationsCharging the battery Installation and connecting the loop generator/chargerInstallation of the boundary wire Best position for the boundary wireBoundaries for the working area 30 cm10 cm Boundaries within the working area Secondary areas SlopesLaying out the boundary wire 3012-745 3012-535 Connecting the boundary wire Checking the installation Linking Automower to the loop generator/chargerStarting Automower UseStopping Automower Adjusting the cutting height Switching off AutomowerRestart Changing the PIN code Sounds Sound SignificanceSelect Control panelNumbers Main switch Indicator lampsProposals for installation Garden exampleGarden with steep inclines can be mown Maintenance BatteryService CleaningWinter storage AutomowerDo not use running water when cleaning Underframe and blade discChassis WheelsReplacing the blades Body3012-260 Trouble shooting Fault messagesTrouble Shooting Fault symptom Environmental Information Technical dataData Automower 210 C EU declaration of conformity EU Declaration of Conformity only applies to EuropeEU Declaration of Conformity Index Trouble Shooting Guide symptom 115 03