Sterling 882.00249.00 manual

Contents

Main SCC 2-Pump 12-Station Controllers Asia/Australia +86 512 8717 1919 Sales and Contracting Department Shipping Information Page Table of Contents CHAPTER 1: SAFETY ................................................................6 CHAPTER 2: FUNCTIONAL DESCRIPTION............................ 10 CHAPTER 3: INSTALLATION ..................................................14 CHAPTER 4: OPERATION ........................................................34 CHAPTER 5: MAINTENANCE................................................... 43 CHAPTER 6: TROUBLESHOOTING......................................... 46 CHAPTER 7: APPENDIX ..........................................................49 CHAPTER 8: SERVICE ONLY INFORMATION ........................57 Chapter 1: Safety 1-1 How to Use This Manual Danger! Warning! Caution! 1-2 Warnings and Precautions 1-3 Responsibility Page Chapter 2: Functional Description 2-1 Models Covered in This Manual 2-2 General Description 2-3 Standard Features 2-4 Optional Features 2-5 Safety Devices and Interlocks Page Chapter 3: Installation 3-1 Uncrating 3-2 Mounting the Control Panel 3-3 Electrical Connections Page 2Pump 12-Station Controllers Chapter 3: Installation 16 Figure 1: Typical 24-Volt Junction Box Wiring Diagram WIRE LUG FIELD WIRING INTERNAL 3-4 Setup Page STATION SETTINGS? NO/YES OPERATION MODE? NO/YES ALL NORMAL MODE? NO/YES ALL SIGHTGLASS MODE? NO/YES STATION: 1 NORMAL Y=NORMAL N=SIGHTGLS SET DUMP DELAY? NO/YES DUMP DELAY 11: 15.0s PRESS ENTER TO SAVE SET INPUT DELAY? NO/YES INPUT DLY 11: 0.250s PRESS ENTER TO SAVE SET STATION ALARMS? NO/YES ALARM 11: ENABLED Y=ENABLE N=DISABLE ALARM AFTER 3 LOADS PRESS ENTER TO SAVE STATION SETTINGS? NO/YES ASSIGN PUMP>STATION? NO/YES PRESS HOPPER <1-12> STATION 10: PUMP 1 SELECT PUMP 1 OR 2 PUMP SETTINGS? NO/YES PUMP MODE? NO/YES SET PUMP MODE? Y=SINGLE N=DUAL SET ACTIVE PUMP SELECT PUMP 1 OR 2 BLOWBACK SETTINGS? NO/YES SELECT PUMP 1 OR 2 USE KEYPAD TO ENTER ENABLE BLOWBACK? NO/YES BLOWBACK PULSES: 10 SETTING FOR PUMP 1 ON TIME: 0.500 s SETTING FOR PUMP 1 OFF TIME: 0.500 s SETTING FOR PUMP 1 BLBK AFTER 12 LOADS SETTING FOR PUMP 1 IDLE DELAY TIME? NO/YES SELECT PUMP 1 OR 2 USE KEYPAD TO ENTER IDLE TIME: 10.000 s SETTING FOR PUMP 1 3-5 Initial Startup LOAD TIME 10: 63sec PRESS ENTER TO SAVE Chapter 4: Operation 4-1 Startup SECTION 1 SECTION 2 SECTION 3 SECTION 4 4-2 Controller Description and Operation STATION:-- OFFLINE TIME: --- LOGO P1:S--:--- OFFLINE P2:S-:--- OFFLINE Page Page Page 4-3 Operation Page Page Chapter 5: Maintenance 2Pump 12-Station Controllers Chapter 5: Maintenance 44 Figure 5: BIOS Connection, Electrical Diagram; Drawing 1 SCHAFFNER - FN1394-10-05-11 N 2Pump 12-Station Controllers Chapter 5: Maintenance 45 Figure 6: BIOS Connection, Electrical Diagram; Drawing 2 A0560970 LEGEND Chapter 6: Troubleshooting 6-1 General Troubleshooting Page WRITING PARAMETERS TO FLASH-PLEASE WAIT SAVING BACKUP TO FLASH-PLEASE WAIT Chapter 7: Appendix 7-1 Warranty Page Page 7-3 Spare Parts List Page Page Page 7-4 Controller Identification (Serial Number) Tag 7-5 Technical Assistance (Contact Information) SET RAMP UP TIME? NO/YES SELECT PUMP 1 OR 2 USE KEYPAD TO ENTER RAMP UP DLY: 1.500s SETTING FOR PUMP n Chapter 8: Service Only Information 8-1 Service Settings Menu SET RAMP DOWN TIME? NO/YES RAMP DN DLY: 8.000s SETTING FOR PUMP n SELECT PUMP 1 OR 2 USE KEYPAD TO ENTER SET PUMP STAGE TIME? NO/YES STAGE DELAY: 3.000s PRESS ENTER TO SAVE SET LCD BLINK DELAY? NO/YES BLINK DELAY: .500s PRESS ENTER TO SAVE HI VAC SENSOR DELAY? NO/YES SELECT PUMP 1 OR 2 USE KEYPAD TO ENTER HIVAC DELAY: 3.000s SETTING FOR PUMP n HI VAC VENT DELAY? NO/YES SELECT PUMP 1 OR 2 USE KEYPAD TO ENTER HV VENT DLY: 10.000s SETTING FOR PUMP n HI VAC LOAD COUNT? NO/YES SELECT PUMP 1 OR 2 USE KEYPAD TO ENTER HV LOAD CNT: 7 SETTING FOR PUMP n INPUT MONITOR? NO/YES IN BNK0: 0000000000 IN BNK1: 0000000000 OUTPUT CONTROL? NO/YES AUTOMATIC OR MANUAL? N=AUTO Y=MANUAL OUTBNK0: 0000000000 OUTBNK1: 0000000000 OEM MENU ACCESS IS NOW AVAILABLE! OEM SETTINGS? NO/YES 8-2 Other Controller Restricted Areas PWL1:1111 PWL2:2222 PWL3:3333 PWL4:4444 ROM CHECKSUM: 0x0000 PRESS YES TO RESUME