Manual Organization | AC International MTA128ST-USB specification

Chapter 1 - Introduction and Description

Manual Organization

This manual is divided into six chapters and two appendixes:

Chapter 1: Introduction and Description—Summarizes product features, lists technical specifications, and provides an overview of the manual’s organization.

Chapter 2: Hardware Installation—Describes how to connect the MTA128ST-USB to the computer, to power, to the ISDN BRI line, and to an optional analog device. It also describes the functions of the front panel LED indicators.

Chapter 3: Software Installation and Configuration — Describes how to install the driver software and how to configure and operate the MTA128ST-USB using the Windows 2000/98/95 software configuration utility.

Chapter 4: AT Commands, S-Registers, and Result Codes— Describes how to use AT commands, S-registers, and result codes to control the MTA128ST-USB through popular communications programs.

Chapter 5: Troubleshooting— Provides tips and advice for troubleshooting your MTA128ST-USB if you think it isn’t working correctly.

Chapter 6: Warranty, Service, and Technical Support— Provides terms of your warranty, describes how to upgrade your unit using the FlashWizard utility, and describes how to get technical support via telephone and the Internet.

Appendix A: Regulatory Compliance— EMC, Safety, and Terminal Directive Compliance.

Appendix B: Configuration Profiles— Describes how to use the Quick Setup Factory Profiles stored in the MTA128ST-USB’s firmware and lists contents of each profile.

7

Image 7

AC International MTA128ST-USB manual Manual Organization, Introduction and Description

Contents

User Guide User Guide Contents Troubleshooting Introduction and Description MultiModemISDN User Guide IntroductionProduct Description Universal Serial Bus USB Introduction and Description Manual Organization Features LED Indicators Technical Specifications Hardware Installation Hardware Installation Safety Warning Telecom/ISDN-STUnpacking Your MTA128ST-USB Assembling the MTA128ST-USB Connecting the MTA128ST-USB to Your SystemMultiModem Isdn User Guide Connecting to Analog Equipment Connecting to Your ComputerConnecting to Power Connecting to Your Isdn Network Terminator LED Indicators References Hardware Installation Data Protocol Software Installation and Configuration Software Installation and Configuration Installing in WindowsInstall Hardware Device Drivers dialog box displays If the Digital Signature Not Found dialog box displays Page Changing the Modem Descriptor Windows Upgrade Device Driver Wizard dialog box displaysMTA128ST-USB CDC ML-PPP Properties dialog box displays Start Device Driver Installation dialog box displays Installing in Windows Software Installation and Configuration MultiModemISDN User Guide MTA128ST-USB ML-PPP Properties dialog box displays Update Device Driver Wizard dialog box displays Upgrade Device Driver Wizard dialog box displays Software Installation and Configuration Removing Your Old Device from Windows 2000 and Windows 98 Click Start Settings Control Panel Network Configuration Configuration AT commands AT!C6= and AT*!C6= Call Control ConfigurationAT commands AT!N1= and AT*!N1= Dialing Stored Numbers To Install in Windows 2000/98/95 Isdn MTA128ST-USB Configuration Utility Windows 2000 Dial-Up Networking MultiModemISDN User Guide If you select Accept incoming connections MultiModemISDN User Guide Windows 98/95 Dial-Up Networking MultiModemISDN User Guide Using AT Commands to Configure the MTA128ST-USB AT Commands AT Commands, S-Registers and Result Codes AT Commands, S-Registers, and Result Codes Entering AT Commands Command Implementation AT Commands by Function Data Call Commands C0=2 Net3 A97=nA97=0 A97=1 DN=1 D3=0-63D3=240 D3=241 D98 EN=nEN=1 EN=2 RXGn N2=nRXG10 L5 and L6 =12 Connect String normally it is issued by itself ATZ #X0 E4, &E6, &E13E12 E13 MultiModemISDN User Guide $Dn ROM Data Call Commands Command DSn Register Summary Registers AT Commands, S-Registers, and Result Codes MultiModemISDN User Guide S31 S30S34 S50 S44S45 S49 S51 Ring S18 S53S54 S17 AT Commands, S-Registers, and Result Codes S59 S58 S61 S60S62 S64 S63S65 S68 S67 S73 S69S70 S71 S76 S75S77 S80 Result Codes Dialing Using AT Commands to Operate the MTA128ST-USBMaking a Call Modes of Operation Answering a Call Hanging Up Troubleshooting None of the LEDs light when the MTA128ST-USB is on MTA128ST-USB dials but cannot make a connection Troubleshooting You can place data calls but not voice calls or vice versa MTA128ST-USB disconnects while online MultiModemISDN User Guide Warranty, Service, and Technical Support Addendum for North American Products Limited WarrantyAddendum for International Products Warranty, Service and Tech Support Out of Warranty Repair Costs On-line Warranty RegistrationSoftware User License Agreement MultiModem Isdn User Guide Technical Support ServiceContacting Technical Support Ordering Accessories Upgrading the MTA128ST-USB with FlashWizard Using FlashWizard to Upgrade Firmware Appendixes Industry Canada EMC, Safety, and Terminal Directive ComplianceAppendix a Regulatory Compliance Class B Statement FCC Part MultiVOIP 200 User Guide Quick Setup Example Profile 1 &F1 V.110 Asynchronous Operation Profile 2 &F2 V.120 Asynchronous Operation Profile 4 &F4 ML-PPP Asynchronous Operation Glossary Glossary Symbol MultiModemISDN User Guide Glossary MultiModemISDN User Guide Glossary 100 TA- See terminal adapter 101 102 103 Index 105 Index 106 42, 52 107 Isdn MTA128ST-USB Config utility 108 Rings