Operating elements and terminal blocks

7.2 Operating elements and terminal blocks

This chapter describes the available terminal blocks, plug connectors and operating elements. Configuration of the 7 pin connector of slots X1 to X8:

1Switched ground potential. All pins 1 of slots X1 – X8 are connected.

2RxD

3TxD

4Ground

5Switchable ground potential. The slots X1 – X8 can be switched as desired.

6Ground

7Ground potential for shield connection

Configuration of the 3 pin connector X11:

X11: +24V

X11: 24V - ground

X11: Grounding, carry out by as short a route as possible.

Page 28

Image 28

AEG Thyro-S H1 manual Operating elements and terminal blocks

Contents

Ethernet Bus Module ProﬁNet Contents List of figures and tables Contact Introduction Safety Identification in the operating instructionsGeneral danger information Electric current Operator requirements Personnel requirementsIntended use Use of the device Maintenance, service, faults Prior to installation / commissioningTransport Processing the setpoint Thyro-S FunctionsProcessing the setpoint Thyro-A Freely addressable digital outputs Processing the setpoint Thyro-Step ControllerRelais Control Installation Connecting a 24 V power supplyConnecting the power controller to Connecting the Ethernet bus module to the master Settings Setting the protocolSetting the number of slots Setting the device name Operating display of the bus module Operating display of the bus moduleOperating status of the Ethernet bus module Status LED of the Ethernet Ports Start configuration parameterization Cyclical data transmission configurationOperation Input and output data Thyro-S Tab b Thyro-S Faults Tab Interpretation of the master setpoint with Thyro-STab Cyclic input and output data with Thyro-S ..H1 Tab Cyclic input and output data with Thyro-S ..HRL1 Input and output data Thyro-A Tab b Thyro-S StatusTab Cyclic input and output data with Thyro-A 1A...H1 Tab Cyclic input and output data with Thyro-A 1A...HRL1 Tab Cyclic input and output data with Thyro-A 2A...H1 Tab Cyclic input and output data with Thyro-A 1A...HRLP1Tab Cyclic input and output data with Thyro-A 2A...HRL1 Tab Cyclic input and output data with Thyro-A 2A...HRLP1 Tab Cyclic input and output data with Thyro-A 3A...H1 Tab Cyclic input and output data with Thyro-A 3A...HRL1 Tab Cyclic input and output data with Thyro-A 3A...HRLP1 Tab a Thyro-A Fault Tab b Thyro-A Status Tab Cyclic input and output data with Thyro-A 1A...C02 Tab Cyclic input and output data with Thyro-A 1A...C01Tab Cyclic input and output data with Thyro-A 1A...C03 Tab Cyclic input and output data with Thyro-A 1A...C05 Tab Cyclic input and output data with Thyro-A 1A...C07Supported operating modes TPM TSC TMU Tab Supported operating modes Tab Cyclic input and output data TPM automatic mode Input and output data Thyro-Power ManagerTab Cyclic input and output data TPM manual mode Tab Cyclic input and output data TSC mode Tab Cyclic input and output data TIO modeInput and output data Thyro-Step Controller Input and output data Thyro Input/Output Unit Tab Cyclic input and output data TMU mode Tab b Fault TPM, TSC, TIO, TMUInput and output data Thyro-Measurement Unit Tab b Status TPM, TSC, TIO, TMU Read data record Rdrec Acyclic data transmission parameterizationWrite data record Wrrec Power supply External connections Operating elements and terminal blocks System interface InterfacesEthernet interfaces Connection diagrams Thyro-A Connection diagram Thyro-A Connection diagrams Thyro-S Connection diagram Thyro-S Connection diagrams TSC Connection diagram TSC Technical Data InstallationService Specific notes Accessories and options Dimension drawingsApprovals and conformity Detail Appendix a Controller parameter HRL1 Hrlp SST RLP1 U16 R309 Index R309 DAC1OF Page Type value U mains U16 …260 Measuring and cycle time …1500