![](/images/new-backgrounds/1299528/29952871x1.webp)
17. Appendix A
1. Acyclic parameter table
Table A:
Controller parameter
Index Symbol
Name
Data type Value range
1 | I_TYP | Controller type current | u16 | 0… |
|
2 | U_TYP | Controller supply voltage | u16 | 0…1000 |
|
3 | P_TYP | Controller type output power | u32 | 0… |
|
6 | BETR | Operating mode | u16 | 0…3 | Reserved, TAKT, VAR, QTM |
7 | AN1 | Phase angle of 1st half wave | u16 | 0…180 |
|
8 | SST | Soft start duration (given) | u16 | 0…1000 |
|
9 | SDN | Soft stop duration (given) | u16 | 0…1000 |
|
10 | T0 | Cycle period duration | u16 | 0…1000 |
|
11 | MP | Minimum interval | u16 | 0…10 |
|
12 | TSMAX | Maximum cycle turn on time | u16 | 1…T0 |
|
13 | TSMIN | Minimum cycle turn on time | u16 | 0…T0 |
|
14 | V_IE | Front pulse stop | u16 | 0…180 |
|
15 | H_IE | Back pulse stop | u16 | 0…180 |
|
16 | RE | Control (analog output value) | u16 | 0…8 | Uload2, Uload eff, Iload2, Iload eff, reserved, real power, |
|
|
|
|
| reserved, reserved, without regulation |
17 | TI_1 | PI controller, I part | u16 | 0= aus 0…65535 |
|
18 | KP_1 | PI controller, P part | u16 | 0= aus 0…65535 |
|
19 | KR_1 | PI controller, counter P part | u16 | 0…65535 |
|
20 | V_IE_2 | Front pulse stop phase 2 | u16 | 0…180 |
|
21 | UEMA | Effective voltage setpoint maximum | u16 | 0… |
|
22 | IEMA | Effective current setpoint maximum | u16 | 0… |
|
23 | PMA | Power setpoint maximum | u32 | 0… |
|
24 | SW_ENABLE | Setpoint activation | u16 | 0…3 | Bit0=1 setpoint x2.4 active, Bit1=1 setpoint |
|
|
|
|
| master active |
27 | SW_REGLER | Setpoint x2.4 | u16 | 0…4096 |
|
28 | OF_1 | Actual value output offset 1 | u16 | 0…4096 |
|
29 | FA_1 | Scale end value actual value output 1 | u16 | 0…4096 |
|
30 | SPG_MIN | Mains voltage monitoring min. | u16 | 0…1000 |
|
31 | SPG_MAX | Mains voltage monitoring max. | u16 | 0…1000 |
|
32 | UN_S | Undercurrent monitoring | u16 | 0…1 | on, off |
33 | RELAIS_CTRL_2 | Relay configuration 2 | u16 | 0…65535 | bit coded |
34 | LASTBRUCH_MIN_ABS | Load fault, minimum value | u16 | 0…4505 |
|
36 | SYNC_ADR | Synchro cycle address | u16 | 0…65535 |
|
37 | IMAB | Pulse | u16 | 0…65535 | bit coded |
38 | STA_RE | Control start controller analog setpoint | u16 | 0…65535 |
|
39 | STE_RE | Control end controller analog setpoint | u16 | 0…65535 |
|
40 |
| Configuration 3A | u16 |
| bit coded |
41 | MOSI_FA | Peak current value limit | u16 | 0…4096 |
|
42 | DAC_1_CTRL | Analog output configuration 1 | u16 | 0…10 |
|
44 | VERS_T | Version day | u16 | 1…31 |
|
45 | VERS_M | Version month | u16 | 1…12 |
|
46 | VERS_J | Version year | u16 | 0…9999 |
|
48 |
| Controller inhibit | u16 | 0…1 | on, off |
49 | RELAIS_CTRL | Relay configuration 1 | u16 | 0…65535 | bit coded |
50 |
| Save | u16 | 0…1 | off, save |
56 | MITTEL | Averaging analog output 1 | u16 | 0…65535 |
|
84 | TEMP | Temperature | u16 |
| |
109 | MITTEL_2 | Averaging analog output 2 | u16 | 0…65535 |
|
110 | OF_2 | Actual value output offset 2 | u16 | 0…4096 |
|
111 | FA_2 | Scale end value actual value output 2 | u16 | 0…4096 |
|
112 | DAC_2_CTRL | Analog output configuration 2 | u16 | 0…10 |
|
115 | MITTEL_3 | Averaging analog output 3 | u16 | 0…65535 |
|
116 | OF_3 | Actual value output offset 3 | u16 | 0…4096 |
|
117 | FA_3 | Scale end value actual value output 3 | u16 | 0…4096 |
|
118 | DAC_3_CTRL | Analog output configuration 3 | u16 | 0…10 |
|
119 | U_MIN | Voltage limit minimum | u16 | 0…65535 |
|
120 | U_MAX | Voltage limit maximum | u16 | 0…65535 |
|
121 | I_MIN | Current limit minimum | u16 | 0…65535 |
|
122 | I_MAX | Current limit maximum | u16 | 0…65535 |
|
123 | P_MIN | Power limit minimum | u32 | 0… |
|
124 | P_MAX | Power limit maximum | u32 | 0… |
|
36