Calibration Record for Agilent E3632A | Agilent Technologies

Chapter 3 Calibration Procedures Calibration Record for Agilent E3632A

Calibration Record for Agilent E3632A

	Step	Calibration Description	Measurement	Supply being
	Step	Calibration Description	Mode (DVM)	Adjusted
			Mode (DVM)	Adjusted

	1	Unsecure the power supply (see page 59).

	2	Turn on "CAL MODE"(simultaneously press "Calibrate" and "Power" keys)
	2	until it beeps.
		until it beeps.

	3	Move down menu to "CAL SETUP 1" (press "Calibrate" key).		Voltage
	3	Move down menu to "CAL SETUP 1" (press "Calibrate" key).		Calibration
				Calibration

		Calibrate DAC and select the low point for voltage calibration; "START
		BITCAL" appears for 3 seconds and the display counts down numbers from		DAC and low
	4	30 to 0. Then, " V LO 0.5000 V" appears on the display(press "Calibrate" key	V	voltage point
		and wait about 30 seconds; then change the display to match the DVM		calibration
		reading).

	5	"V MI 15.000 V" appears on the display (press "Calibrate" key; then change	V	Middle voltage
	5	the display to match the DVM reading).	V	point calibration
		the display to match the DVM reading).		point calibration

	6	"V HI 29.500 V" appears on the display (press "Calibrate" key; then change	V	High voltage point
	6	the display to match the DVM reading).	V	calibration
		the display to match the DVM reading).		calibration

	7	"CAL SETUP 2" now appears on the display (press "Calibrate" key).	V	OVP calibration

	8	"CAL SETUP 3" now appears on the display (press "Calibrate" key; then		Current
	8	connect 0.019resistor across the output terminals).		calibration
		connect 0.019resistor across the output terminals).		calibration

	9	"I LO 0.200 A" appears on the display (press "Calibrate" key; then change	A	Low current point
	9	the display to match the computed current through 0.019resistor).	A	calibration
				calibration

	10	"I MI 3.500 A" appears on the display (press "Calibrate" key; then change the	A	Middle current
	10	display to match the computed current through 0.019resistor).	A	point calibration
				point calibration

	11	"I HI 6.9000 A" appears on the display (press "Calibrate" key; then change	A	High current point
	11	the display to match the computed current through 0.019resistor).	A	calibration
				calibration

	12	"CAL SETUP 4" now appears on the display (press "Calibrate" key).	A	OCP calibration

	13	Press "Calibrate" key, then press "Power" switch.		Exit CAL MODE

3

69

Image 70

Agilent Technologies manual Calibration Record for Agilent E3632A

Contents

Service Guide 3DUW1XPEHU $SULO Convenient bench-top features Flexible system features Front Panel at a Glance Before performing calibration Front-Panel Voltage and Current Limit Settings T e Display Annunciators OVP Rear Panel at a Glance Key to This Book Page Contents Contents Theory of Operation Service Contents Specifications Specifications Performance Specifications Specifications Performance Specifications OVP Supplemental Characteristics Specifications Supplemental Characteristics Opt 0E3 Dimensions of Agilent E3632A Power Supply Specifications Supplemental Characteristics Quick Start Quick Start Connect the power cord and turn on the power supply To Prepare the Power Supply for UseQuick Start To Prepare the Power Supply for Use Enable the outputs 100 or 115 Vac, 4 AT fuse 230 Vac, 2.5 AT fuse Quick Start To Check the Rated Voltages of the Power Supply To Check the Rated Voltages of the Power SupplyTurn on the power supply Quick Start To Check the Rated Currents of the Power Supply To Check the Rated Currents of the Power SupplyAdjust the voltage limit value to 1.0 volt Page Adjust the knob for the desired current limit To Use the Power Supply in Constant Voltage ModeSet the display for the limit mode Connect a load to the desired output terminals T e Adjust the knob for the desired output voltage Return to the meter mode Adjust the knob for the desired voltage limit To Use the Power Supply in Constant Current ModeConnect a load to the output terminals T e Adjust the knob for the desired output current Verify that the power supply is in the constant current mode To Store and Recall the Instrument State Done Turn on the recall modeRestore the operating state Recall Setting the OVP Level and Enable the OVP Circuit To Program Overvoltage Protection Checking OVP Operation Readjust the OVP trip level or the output voltage levelMove to the clear mode Ovp on Clearing the Overvoltage Condition Clear the overvoltage condition and exist this menu Setting the OCP Level and Enable the OCP Circuit To Program Overcurrent Protection Checking OCP Operation Readjust the OCP trip level or the output current levelMove to the clear mode Ocp on Clearing the Overcurrent Condition To Rack Mount the Power Supply Quick Start To Rack Mount the Power Supply Calibration Procedures Calibration Procedures Agilent Technologies Calibration Services Calibration Interval Calibration Procedures Automating Calibration Procedures Automating Calibration ProceduresRecommended Test Equipment U t i o n Calibration Procedures Test Considerations Test Considerations Self-Test Calibration Procedures Performance Verification TestsPerformance Verification Tests Performance Verification Tests Setup for Most Tests Measurement Techniques General Measurement Techniques Constant Voltage CV Verifications Constant Voltage Test SetupCalibration Procedures Constant Voltage CV Verifications Voltage Programming and Readback Accuracy CV Line Regulation CV Load RegulationVolt Normal Mode Voltage Noise CV Ripple and Noise Load Transient Response Time Constant Current CC Verifications Constant Current Test SetupCalibration Procedures Constant Current CC Verifications Current Programming and Readback Accuracy CC Load Regulation Curr Normal Mode Current Noise CC Ripple and Noise CC Line Regulation Common Mode Current Noise Calibration Procedures Common Mode Current Noise CV Performance Test Record Performance Test Record for Agilent E3632ACC Performance Test Record Calibration Procedures Calibration Security Code Calibration Security Code Turn on the front-panel calibration mode To Unsecure the Power Supply for CalibrationMove to the security code by pressing the Secure key To Unsecure the Power Supply Without the Security Code Turn off the calibration mode Calibration Count Calibration Procedures Calibration CountCalibration Message General Calibration/Adjustment Procedure Voltage and OVP Calibration Move down a level to the voltage calibration modeCalibrate DAC and select the low voltage calibration point Lo +0.5000 Hi 28.995 Current and OCP Calibration Lo 0.200 a Select the low current calibration point Mi 3.499 a Turn off the power supply to exit the calibration mode Aborting a Calibration in Progress Calibration Procedures Calibration Record for Agilent E3632A Calibration Record for Agilent E3632A System Error Messages Error MessagesCalibration Procedures Error Messages Self-Test Error MessagesPage Calibration Procedures Calibration Program Calibration Program Clear Screen Print TABXY10,7,BEGIN DAC Error Correction Else Print TABXY10,7,BEGIN CURRENT/OCP Calibration End of Program Print TABXY10,5,CURRENT/OCP Calibration Complete Theory of Operation Theory of Operation Block Diagram Overview Theory of Operation Block Diagram Overview Block Diagram AC Input and Bias Supplies Theory of Operation AC Input and Bias Supplies Floating Logic Theory of Operation Floating Logic Serck Xfpsk To-A Converter Theory of Operation To-A Converter To-D Converter Theory of Operation To-D Converter Power Mesh and Control Theory of Operation Power Mesh and Control Theory of Operation Power Mesh and Control Front Panel Earth-Referenced LogicTheory of Operation Earth-Referenced Logic Service Service Does the Power Supply Fail Self-Test? Operating ChecklistIs the Power Supply Inoperative? Service Operating Checklist Service Types of Service Available Types of Service AvailableStandard Repair Service worldwide Express Exchange U.S.A. only Service Repacking for Shipment Repacking for Shipment Service Electrostatic Discharge ESD Precautions Electrostatic Discharge ESD PrecautionsTo Replace the Power-Line Fuse Surface Mount Repair Installation Procedure To Disconnect the Output Using an External RelayService To Disconnect the Output Using an External Relay U t i o n Service Troubleshooting Hints Troubleshooting HintsUnit Reports Errors 740 to Unit is Inoperative Bias Supplies Problems Service Troubleshooting Hints Service Self-Test Procedures Self-Test ProceduresPower-On Self-Test Complete Self-Test ±10% tolerance Service Self-Test Procedures 100 Replaceable Parts To Order Replaceable Parts E3632-60002 Main PC Assembly KMG1H222H E3632-60002 Main PC Assembly Replaceable Parts 105 106 107 108 109 110 E3632-60004 Front Panel Display PC Assembly Agilent Part Qty Description Mfr Mfr Part Number Code E3632-60005 Front Frame Assembly E3632A Power SupplyAssembly Manufacturer’s List Mfr Code Manufacturer’s Name 114 Backdating Lqfoxghglqwklvfkdswhu Schematics ‡ $&DQG$&6\VWHP6FKHPDWLFSDJH ‡ &RPSRQHQW/RFDWRU0DLQ%RDUGSDJH‡ &RPSRQHQW/RFDWRUURQWSDQHOSDJH Page Page Page Page Page Page Page Page Warranty