Declaration | Agilent Technologies N3280A manual

Declaration Page

DECLARATION OF CONFORMITY

According to ISO/IEC Guide 22 and CEN/CENELEC EN 45014

Manufacturer’s Name:	Responsible Party	Alternate Manufacturing Site
Manufacturer’s Name:	Agilent Technologies, Inc.	Agilent Technologies
Manufacturer’s Address:	Power Products PGU	South Queensferry
	140 Green Pond Road	West Lothian EH30 9TG
	Rockaway, New Jersey 07866	United Kingdom
	U.S.A
declares that the product:
Product Name:	Component Test dc Source
Model Number:	N3280A
Product Options:	This declaration covers all options of the above product(s).

Conforms with the following European Directives:

The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC (including 93/68/EEC) and carries the CE Marking accordingly

EMC information:

The product herewith complies with the requirements of the EMC Directive 89/336/EEC (including 93/68/EEC) and carries the CE Marking accordingly (European Union).

As detailed in Electromagnetic Compatibility (EMC) Certificate of Conformance No.TCF CC/TCF/01/016 based on Technical Construction File (TCF) No. ANJ13, dated 8/03/2001

Assessed by: Celestica Ltd, Appointed Competent Body

Westfields House, West Avenue

Kidsgrove, Stoke-on-Trent

Straffordshire, ST7 1TL

United Kingdom

Safety information:

The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC and carries the CE-marking accordingly

Supplemental information

The product conforms to the following safety standards:

IEC 1010-1:1990+A1+A2 / EN 61010-1:1993 +A2

UL 3111-1:1994

CSA C22.2 No. 1010.1:1993

March 19, 2001
Date	Hank Kowalla / Quality Manager at PPPGU

For further information, please contact your local Agilent Technologies sales office, agent or distributor. Authorized EU-representative: Agilent Technologies Deutschland GmbH, Herrenberger Straβe 130, D71034 Böblingen, Germany

5

Image 5

Agilent Technologies N3280A manual Declaration

Contents

Agilent Technologies Model N3280A Component Test DC Source USER’S Guide Certification Warranty Information General Safety Summary Safety Symbols Declaration Printing History Acoustic Noise Information Table of Contents Scpi Command Completion Using Device Clear Types of Scpi CommandsExternal References Gpib Capabilities of the DC Source Introduction to Scpi Measurement Commands Scpi Programming Commands At a Glance Calibration CommandsOutput Commands Status Commands Trigger Commands System CommandsCommon Commands Voltage Priority Tests Transient Response Tests Error Number List 103Ripple and Noise Tests Page Document Orientation Safety Considerations Description Options and AccessoriesRemote Programming Option Description Voltage Priority Operation Output Characteristics Current Priority Operation Output Characteristic Current Priority Measurement Characteristics Start of a Measurement Inspection CleaningDamage Packaging Material Additional Items Bench Operation LocationRack Mounting Do not block the fan exhaust at the rear of the unit Connect the Power Cord Power Connections Outputs 1 Turn the unit off before connecting any wiresOutput Connections Voltage Drops and Lead Resistance Current RatingsAmpacity and Resistance of Stranded Copper Conductors AWG No Maximum Ampacity Resistance at 20 deg. C Free air Guard Connections for Test Fixtures Coaxial Guard Connections Computer Connections External Trigger ConnectionsMaintaining Stability OVP Considerations Switch Setting Settings for Power Module Configuration SwitchSwitch Setting Address Gpib Address Front Panel Description Explanation Checkout ProcedureProcedure Runtime Error Messages Selftest Error MessagesPower-On Selftest Errors Case of TroublePage Gpib Capabilities of the DC Source External ReferencesGpib References Scpi References Conventions Used in This Guide Types of Scpi CommandsIntroduction to Scpi Including Common Commands Multiple Commands in a MessageUsing Queries Moving Among Subsystems Channel List Parameter Types of Scpi MessagesMessage Unit Scpi Data Formats Suffixes and Multipliers Scpi Command CompletionResponse Data Types Class Suffix Unit Unit with Multiplier Outputstate Example Using Device ClearPage Introduction Power-on InitializationProgramming the Output Enabling the Output Output Current Output ModeOvervoltage Protection Output Trigger Model Triggering Output ChangesOscillation Protection Selecting the Output Trigger Source Setting the Voltage and Current Trigger LevelsEnabling the Output Trigger System Average Measurements Making MeasurementsGenerating Output Triggers Measurement Samples and Time Interval Power Line Cycles Current Ranges Triggered MeasurementsWindow Functions Returning All Measurement Data From the Data Buffer Selecting the Measurement Trigger Source Measurement Trigger ModelEnabling the Measurement Trigger System Generating Measurement Triggers Output Settling DelaySelecting the Sensing Function Pre-trigger and Post-trigger Acquisition Pre-trigger and Post-trigger Data Acquisition DC Source Status Model Programming the Status Registers Operation Status Group Bit Configurations of Status Registers Standard Event Status Group Questionable Status GroupStatus Byte Register MSS and RQS Bits Servicing Operation Status and Questionable Status Events Determining the Cause of a Service Interrupt Programming Parameters Subsystem CommandsCommon Commands Save new cal constants in non-volatile memory Scpi Programming Commands At a GlanceSubsystem Commands Syntax FUNCtion Mode mode, @list VOLTage Mode mode, @list DELaySets the output voltage in voltage priority mode Sets the triggered output voltage in voltage priority mode ESE n Common Commands SyntaxSRE n Output Programming Parameters CALibrateCURRent Calibration CommandsCALibrateCURRentLIMitPOSitive CALibrateCURRentLIMitNEGative CALibrateCURRentMEASure CALibrateDATA CALibratePASSwordCALibrateDATE CALibrateLEVel CALibrateVOLTage CALibrateSAVECALibrateSTATe FETChARRayCURRent? FETChARRayVOLTage? Measurement CommandsFETChCURRent? FETChVOLTage? Query Syntax MEASureCURRent? MEASureVOLTage? MEASureARRayCURRent? MEASureARRayVOLTage?SENSeCURRentRANGe Enter values greater than 0.015A SENSeSWEepNPLCycles SENSeFUNCtionSENSeSWEepOFFSetPOINts Query Syntax SENSeFUNCtion? @channel list SENSeWINDow SENSeSWEepPOINtsSENSeSWEepTINTerval OUTPut Output CommandsOUTPutOSCProtect OUTPutPROTectionCLEar SOURceCURRentIMMediate SOURceCURRentTRIGgered Default SuffixSOURceCURRentLIMitIMMediate SOURceCURRentLIMitTRIGgered SOURceCURRentLIMitBWIDth SOURceCURRentMODE SOURceCURRentLIMitMODE SOURceDELaySOURceDELayMODE SOURceVOLTageALCBWIDth SOURceFUNCtionMODESOURceVOLTageIMMediate SOURceVOLTageTRIGgered Query Syntax SOURceFUNCMODE? @channel list SOURceVOLTagePROTectionSTATe SOURceVOLTageMODEQuery Syntax SOURceVOLTagePROTectionSTATe? @channel list NR10 or STATusOPERationENABle Status CommandsBit Configuration of Operation Status Registers STATusOPERationEVENt? Parameters Preset Value STATusPRESetCommand Syntax STATusPRESet Parameters None Examples STATusOPERationNTR STATusOPERationPTR Query Syntax STATusQUEStionableENABle? @channel list STATusQUEStionableENABleSTATusQUEStionableCONDition? STATusQUEStionableNTR STATusQUEStionablePTR SYSTemVERSion? System CommandsSYSTemERRor? ABORt Trigger CommandsINITiateNAME TRIGgerACQuire TRIGgerTRANsientSOURce TRIGgerACQuireSOURceTRIGgerTRANsient RST Value Command Syntax *CLS Parameters None Common CommandsParameters Power-On Value Examples Bit Configuration of Standard Event Status Enable Register Query Syntax *OPT? Returned Parameters Aard Field InformationExample RST Settings Power-on Value Query Syntax TST? Returned Parameters NR1 Bit Configuration of Status Byte Register Table A-1. Specifications Table A-2 Supplemental Characteristics Safety Output Common ModeDimensions Weight Figure A-1. Output Impedance Graphs all outputs Equipment Required Measurement Techniques Performance & Verification Tests Programming Test SetupElectronic Load Voltage Priority Tests Program CommandsVoltage Programming and Readback Accuracy Positive Current Limit +CL Negative Current Limit -CL Action Program Commands Current Programming and Readback Accuracy Current Priority Tests Voltage Priority, Constant Voltage Load Effect Load Effect Tests Voltage Priority, -Current Limit Load Effect Test Voltage Priority, +Current Limit Load Effect Voltage Priority, Constant Voltage Source Effect Source Effect TestsCurrent Priority Constant Current Test Voltage Priority, -Current Limit Source Effect Voltage Priority, +Current Limit Source Effect Current Priority, Constant Current Source Effect Voltage Priority Ripple and Noise Ripple and Noise Tests Current Priority Ripple and Noise Voltage Priority, Transient Recovery TimeTransient Response Tests Figure B-2. Transient Waveform Voltage Priority Current Priority Transient Recovery Time Figure B-3. Transient Waveform Current Priority Performance Test Equipment Form Performance Test Record Form Enable Calibration Mode Performing the Calibration Procedure Positive Current Limit Calibration Negative Current Limit Calibration5A Range Current Measurement Calibration 100 101 15mA Range Current Measurement CalibrationSaving the Calibration Constants Calibration Error Messages Changing the Calibration PasswordTable B-3. Gpib Calibration Error Messages Error Meaning 103 Error Number ListTable C-1. Error Numbers 104 Error Messages 105 Error Messages CPage 107 Line Voltage SelectionPage Mating Connector Part Numbers Earlier Version Output ConnectorsRear Panel Pinout Assignments CHG-2010-J01010-KEPPage 111 Index 112 Index Scpi 113 114 Canada Australia/New Zealand United States Latin AmericaEurope Asia Pacific Japan Manual Updates