Manuals / Aiphone / Communications / Intercom System

Aiphone FK1629 B 0811YZ Network, 10BASE-T Ethernet, 100BASE-TX Ethernet, Web browser

Models: FK1629 B 0811YZ

1 31

Download 31 pages 47.56 Kb

Page 13

STARTING UP THE SYSTEM AND PREPARING FOR THE SETTINGS

STARTING UP THE SYSTEM AND PREPARING FOR THE SETTINGS

The system settings are mainly made on the PC by accessing the web browser for the settings incorporated with the IP unit as the IP host unit. It is recommended to use only one PC for the settings that is connected to the system.

System requirements for PC

Your PC and operating environment must meet the following system requirements to make the settings.

Network	10BASE-T Ethernet, 100BASE-TX Ethernet

Web browser	Internet Explorer 6.0 or later (with Internet Options SSL 3.0 enabled)

GETTING STARTED SETTING

Starting up the system

1 Connect a PC to the IP unit.

[When connecting a PC to the IP unit via a hub (switch)]

IP master station	IP video door station
(IS-IPMV)	(IS-IPDV or IS-IPDVF)

or

LAN/PoE

RJ45

100m (330')

CAT5e/6

(Straight-through cable)

10BASE-T/

100BASE-TX

RJ45

RJ45

Hub

(Switch)

CAT5e/6

100m (330')

10BASE-T/

(Straight-through

100BASE-TX

cable)

RJ45

PC

NOTES:

•Be sure to connect the CAT5e/6 cable to the LAN ports of both units.

•The IP address of IP unit is set to (192.168.0.40) and Subnet Mask is set to (255.255.255.0) as default. Change the IP address of your PC if needed.

[When connecting a PC to the IP unit directly]

IP master station	IP video door station
(IS-IPMV)	(IS-IPDV or IS-IPDVF)

or

LAN/PoE
RJ45	PC
	PC
CAT5e/6 (Crossover cable)	RJ45
100m (330')
10BASE-T/100BASE-TX

NOTES:

•When connecting a PC to the IP unit directly, use an Ethernet crossover cable.

•The IP address of IP unit is set to (192.168.0.40) and Subnet Mask is set to (255.255.255.0) as default. Change the IP address of your PC if needed.

(Continued on next page)

THE SYSTEM USING THE SYSTEM

APPENDIX

13

Image 13

Aiphone FK1629 B 0811YZ Network, 10BASE-T Ethernet, 100BASE-TX Ethernet, Web browser, Connect a PC to the IP unit

Contents

Network Direct System SETTING MANUALIS SERIES Commercial & Security IP Video Intercom systemsettings CONTENTSThe basic setting procedure Making network settings toABOUT THIS MANUAL PURPOSE OF THE SYSTEM SETTINGSManual conﬁgurations Note the followingSetting range SETTING LISTDefault TitleDefault Setting rangeGETTING STARTED SETTING THE SYSTEM USING THE SYSTEM APPENDIX TitleDefault Setting rangeTitle Sub titleDefault Setting rangeGETTING STARTED SETTING THE SYSTEM USING THE SYSTEM APPENDIX Titlefrom the chart below, then start the network settings by SYSTEM SETTING FLOWGo to P First select theIP host unit A static IP address is set FlowSTART For the IP host unit All units Static IP addresses are setFor each IP client unit FlowFlow All units IP addresses are assigned by the DHCP server automaticallySTART Procedure Remote site connection settingsGlobal IP address Connection port global Connection Password Network setting Individual Default Gateway Network setting CommonWhen connecting a PC to the IP unit via a hub switch Internet Explorer 6.0 or later with Internet Options SSL 3.0 enabledWhen connecting a PC to the IP unit directly Network5 Log in to the system by setting the following items 2 Turn on the power to the IP unitPassword Enter “aiphone” 3 Start up the PC, and then open the browser windowSetting window example Setting contents display area THE SYSTEM SETTING DETAILSTable of contents The setting procedureMaking network settings for the whole system Network setting Common Making network settings to each IP unit Network setting Individual1 Click Network setting Individual in the table of 1 Click Network setting Common in the table ofNew administrator ID Enter the new ID Setting the administrator ID and password Administrator settingCurrent Password Enter the current password New Password Enter a new passwordRequired Registering zones System setting - Zone registration1 Click IP unit registration in the table of contents Registering IP units System setting - IP unit registration4 Enter data or change settings for the registered IP units as needed 3 Check the boxes for the IP units you want to register1 Click Registering stations in the table of contents Registering stations System setting - Registering stationsHow to select multiple stations Collective settingMaking detailed settings to door stations Basic setting procedureClick Advanced station settings in the table of contents When you have ﬁnished making all the detailed settingsB Settings on Other window Making detailed settings to master stationsC Settings on Stations to be scan monitored window D Settings on Other window1 Click Registering daily transfer schedule in the Registering stations to zones System setting - Zone setting1 Click Transfer schedule setting in the table of contents Transfer setting - Transfer schedule setting3 Make the settings in the displayed windows to save the current setting1 Click Timer setting in the table of contents Setting the timer Timer settingScan monitor Switching 2 Set the time for the following operations respectively2 Make the setting by clicking 1 Click Remote site pilot call setting in the table ofthe setting items G , H 3 Make the setting in the displayed windows1 Click Video setting in the table of contents Setting time and date Time and date setting2 Set the following settings for video quality 1 Click Time and date setting in the table of contentsWhen downloading setting data onto the PC Downloading/uploading setting data Setting ﬁleWhen uploading setting data 1 Click Downloading setting data in the table of contentsUpdating the ﬁrmware Firmware update MAINTENANCEReferring to the troubleshooting guide Troubleshooting Downloading updated ﬁrmware dataSetting Information Memo