UniLinc Identification

Operational Keypad

The control includes seven keypads. These functions are available to the operator and are intended to control and manage operation of the washer-extractor. Refer to Figure 5 and Table 1.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PHM1401C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Keypad

 

 

 

 

 

Description

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press to move the cursor on display to edit programming values. Also, press

LCD/UP ARROW

while in Cycle Menu or Run Menu to change to the Contrast Adjust/Backlight

Menu. Also, press with

and

 

 

to enter System Menu.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UNLOCK/DOWN ARROW

Press to move the cursor on display, edit programming values, or unlock door.

The door can only be unlocked while the machine is idle.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LEFT ARROW

Press to move cursor on display.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BACK

Press to move back to the previous display menu. Also, press with

 

and

 

 

to enter System Menu. Also, back from the Cycle Menu to enter the

 

 

 

 

 

 

 

 

 

 

 

Service Schedule Menu.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RIGHT ARROW

Press to move cursor on display. Press while running a cycle to get to Run

Diagnostic Menu. Press and hold with

 

 

to enter Delayed Start Menu.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Press to stop and abort a machine cycle during Run Mode. Also press with

STOP/ON/OFF

 

 

 

 

and

 

to enter System Menu. Press with

to enter Delayed Start

 

 

 

 

 

 

 

 

 

Menu.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

START/ENTER

 

 

 

 

Press to start or rapid advance a machine cycle during Run Mode. Also, press to

 

 

save edited programming values when used in programming menus.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Table 1

 

 

 

 

 

 

 

 

16

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F8138801