Manuals / Brands / Laundry Appliance / Washer / Alliance Laundry Systems / Laundry Appliance / Washer

Alliance Laundry Systems PHM1401C Diagnostic, Diagnostic Menu, Test Menu, Test Cycle, Test Balance, Weight, Factory Valve, Purge

1 82

Download 82 pages, 1.6 Mb

Diagnostic

Diagnostic Menu

Test Menu

Test		Water Leak
Test		Detection
		Detection

Alarms		Machine ID

Test Cycle

Test Balance

Weight

Factory Valve

Purge

Inputs Outputs

Diagnostic Menu

PHM1265R

Figure 61

The Diagnostic Menu contains Test, Alarm and Machine ID Menus. The menus contain specific diagnostic information and manufacturing data for the

machine. The

and

keypads

position the highlighted box. Press the keypad to select the menu choice.

Press the keypad while in the Diagnostic Menu to return to System Menu.

Test Menu

PHM1056R

Figure 62

The Test Menu provides features for manufacturing and customer service testing. The highlighted box is

moved horizontally and vertically using the

and keypads. Press the keypad to select the menu choice.

Press the keypad to return to Diagnostic Menu.

F8138801

Contents

Keep These Instructions for Future Reference www.comlaundry.com Page Safety Information Table of Contents Introduction Preliminary Information UniLinc Identification Menu Navigation Programming UniLinc Program Menu Global Setup Diagnostic Machine Identification Laundry Management Maintenance Cycle Charts Safety Information Explanation of Safety Messages Important Safety Instructions Page Safety Decals Operator Safety Safe Operating Environment Environmental Conditions Machine Location Input and Output Services AC Inverter Drive Introduction Model Identification Nameplate Location Replacement Parts Customer Service Model Number Familiarization Guide - Models through May 3rd UW060TVQU10001 UWN060T3VXU1001 Preliminary Information About the Control Power Failure Recovery Communications Audit Information IR Communications Menu IR Communications Error Menu Restore to Factory Defaults Entering Program Mode UniLinc Identification Operational Keypad Operation Modes General Modes of Operation Power-upMode Idle Mode Run Mode Machine Cycle Definition and Operation Machine Cycle Operation Delayed Start Feature Jog Feature UW150 Only Rotation Sensor Equipped To Start a Cycle Run Menu Page Contrast/Backlight Menu Contrast Backlight Close Door Menu Lubricate Bearings Menu Run Diagnostic Menu Speed, Temp and Level Alarms Speed, Temp and Water Level Menu Cycle Aborted Retry Menu Heater Alarm Time Exceeded Press START Key to Retry Press STOP Key to Abort Cycle Cycle Aborted Fatal Menu Water Level Sensor Error Press BACK Key to Return to Cycle Menu Cycle Stopped Menu Delayed Start Countdown Menu Delayed Start Activated Press Start to Run Cycle Press Stop to Abort Delayed Start Final Countdown Menu Menu Navigation The UniLinc Menu Navigation on a Single Screen Menu Navigation with Parameters Screen to Screen Navigation using the Arrow Keypads Display Screen Maps System Menu Map Tree Run Menu Map Tree Service Menu Map Tree Programming UniLinc System Menu Program Diagnostic Laundry Reset Bearing Program Menu Program Menu Modify Cycle Global Setup Modify Cycle Available Characters Cycle, Segment and Step Programming Flow Diagram Step Menu Navigation Reuse Fill Step Menu Fill Step Menu Heater Option Supply A and B Step Menu Agitate Step Menu Cool Down Step Menu Drain Step Menu Spray Rinse Extract Step Menu Extract Step Menu End of Segment Audio Signal Step Menu Global Setup Global Setup Menu Language Menu Date/Time Menu Water Level Menu Temperature Menu Audio Menu Balance Retry Menu Number of Retries Water Management Menu Page Alarms Program Menu Rapid Advance Menu Enable the Rapid Advance Feature During Cycle Operation Shakeout Menu Shake Out Time Banners Menu Factory Defaults Menu Water Level Confirmation Menu Are you sure you want to restore water level settings Water Temperature Confirmation Menu to restore water temperature Audio Confirmation Menu to restore audio settings Reset All Factory Defaults Confirmation Menu Factory Defaults Second Diagnostic Diagnostic Menu Test Menu Test Cycle Test Balance Test Cycle Displayed Description (*1) (*3) Factory Valve Purge Menu Press START to Begin Test Balance Weight Menu Press START Inputs Outputs Menu Outputs Inputs Water Leak Detection Diagnostic Alarms Machine Identification Machine Errors Door Lock Error Door Open Error Drain Alarm Error Drive Fault Error Fill Alarm Error Frame Balance Switch Error Open Temperature Sensor Error Rotation Sensor Error Unbalance Error Heat Alarm Error Water Level Sensor Error PDA Communications Error Water Leak Detection Error Slow Drain Detected During A Machine Cycle Error Laundry Management Total Number of Machine Cycle Counters Total Number of Operating Minutes Counters Last 10 Machine Cycles Rapid Advanced or Stopped Service Schedule Menu Daily Weekly Monthly Quarterly Daily Menu (Service) Weekly Menu (Service) Monthly Menu (Service) Quarterly Menu (Service) Cycle Charts Cycle Charts