Auto Cycle Time Out, Language | American Dryer Corp Phase 7.2.2

Auto Cycle Time Out

While holding the stop/	Ready
clear key, press the up
arrow key.
0:SELECT
LANGUAGE

		Or number
Use arrow		Or number
key

Press and hold the

stop/clear key

1

Press ENTER to jump

directly to the location

1:SELECT SYSTEM PARAMETERS

Press ENTER to access

0: DRYER SETUP

Press ENTER to access

0:SELECT MODEL

Next page

45

Image 47

American Dryer Corp Phase 7.2.2 user manual Auto Cycle Time Out, Language

Contents

NON-COIN Retain This Manual In a Safe Place For Future Reference Table of Contents Section Phase 7 NON-COIN Auto Cycle Patent no ,827,627 Section Features Keyboard Touch Pad Symbols = STOP/CLEAR key Preprogrammed Cycles Program SelectionsPage Timed Manual Drying Cycle Operation Manually Loaded CyclesAutomatic Drying Cycle Patent no ,827,627 Operations Light Emitting Diode L.E.D. DOT Matrix Display Cycle in Progress Temperature DisplayTemperature Conversion Status Preprogrammed Cycle Preview Wrinkle Guard ProgramAudio Alert on Times 0 to Program Locations DiagnosticsReversing Option Page Preprogrammed Locations for Custom Drying Operating Sequence Operating InstructionsPage Page MAN Operating Notes Fire Suppression System F.S.S. Theory of Operation System Reset Fire Suppression System F.S.S. Valve Check Page E.D. Display Operating Status D. Display Messages Introduction to Programming Programming InstructionsPage START/ENTER STOP/CLEAR Programming Flowcharts Phase Menu Programming Procedure Page Auto Reverse Mode On OFF Espanol Selecting Languages0SELECT Language English Select Model Dryer SetupSelecting a Dryer Model Select System Parameters Electric Reversing GAS ReversingGAS REVERSING, Electric REVERSING, Steam REVERSING, GAS NON Steam NON-REVERSING Selecting the System Temperature DEG C Enter Lint Cleaning Frequency 1 to 10 HoursDEG F Setting the Lint Cleaning Frequency Enter Audio Alert on Times 0 to Adjusting the Audio Alert On times System Temp Rotation Sensor Rotation Sensor Press Enter to jump directly to the location Board Address 00 to ZZ OFF Dryer Address To ZZ Auto Cycle Time OUT to 99 Minutes Auto Cycle Time Out Enter Audio Alert on Times 0 to Rotation Sensor System Temp Enter Lint Cleaning Frequency 1 to 10 Hours Auto Cycle Time OUT To 99 Minutes Adjusting Reversing Spin Time and Stop Time Enter Stop Time 5 to 10 Seconds Reversing SetupEnter Spin Time 30 to 120 Seconds Press the up arrow key to increment Wrinkle Guard Audio Alert Setup Wrinkle Guard Audio Alert Wrinkle Guard Setup Steam Injection Setup Wrinkle Guard Setup Steam Injection Setup Cycle Enter 1ST on Time Enter 1ST OFF Time 511 to 000 First time adjustment is Minutes mm Enter 2ND on Time Program 0-40 Cycles Enter 3RD on Time Program System Cycles Parameters Programming a F Cycles or 0 40 Cycles Auto Reverse ModeSelect a F KEY Select Cycle Type Time Not AvailableEnter DRY Temp OFF Not Available Enter Stop Time To 10 Seconds Enter Dryness LevelDRY Enter DRY Time 0 to 99 Minutes Enter Cycle AdjustmentDRY or Extra Extra DRY Enter Cool Down Time 0 to 99 Minutes Controlled Cool Down Enter Cool Down Enter Cool Down Temp 70 to 100 ºF Steam Injection Cycle Enter 1ST on Time 511 to From Previous Enter 2ND on Time Enter 3RD on Time Restoring Factory Default Settings Enter Password Confirm Defaults YES Defaults SET Default Settings Cycle 0-40 Parameters Programs Preset by the Factory Cycle A-F Parameters Programs Preset by the Factory Preprogrammed Cycles Fixed Parameters System Parameters Program Locations Gas Standards Diagnostic L.E.D. Display Fault MessagesPage Page Page S.S. Diagnostic Conditions Brhl RED L.E.D INPUT/OUTPUT I/O Board L.E.D. Indicators Keyboard Touch PAD Layout Customer Custom Parameter Settings Auto Programmed Cycle Page ADC Part No 08/19/08