Not Available, Enter DRY Temp | American Dryer Corp Phase 7.2.2

From

Previous

(A)

Press ENTER to access

Non reversing
models will display
"NOT AVAILABLE"	ON
and jump to 1:	ON
ENTER DRY
TEMP 160 TO
200ºF
Press the Up or
Down Arrow Key to
turn reversing ON
or OFF

OFF

Press ENTER to store

new changes

Axial models will
display 1: DRYING	1: ENTER DRY TEMP
TEMP 160ºF	1: ENTER DRY TEMP
ONLY, then jump	160 TO 200ºF
to 2: ENTER
DRYNESS LEVEL.
Press ENTER to access

160

Next

Page (A)

From

Previous

(B)

Press ENTER to store

new changes

0:REVERSE MODE

		Press ENTER to access
		Non reversing
		models will display
	OFF	"NOT AVAILABLE"
	OFF	and jump to
		and jump to
		1: ENTER DRY
		TIME
		Press the Up or
		Down Arrow Key to
		turn reversing ON
		or OFF

ON

If reversing is OFF,

once Enter is pressed, the

program will jump to

1: ENTER DRY

TIME

ENTER SPIN TIME 30

TO 120 SECONDS

60

Next

Page (B)

61

Image 63

American Dryer Corp Phase 7.2.2 Enter DRY Temp, OFF Not Available, Enter DRY Time Enter Spin Time To 120 Seconds

Contents

NON-COIN Retain This Manual In a Safe Place For Future Reference Table of Contents Section Phase 7 NON-COIN Auto Cycle Patent no ,827,627 Section Features Keyboard Touch Pad Symbols = STOP/CLEAR key Preprogrammed Cycles Program SelectionsPage Manually Loaded Cycles Automatic Drying Cycle Patent no ,827,627 OperationsTimed Manual Drying Cycle Operation Cycle in Progress Temperature Display Temperature Conversion StatusLight Emitting Diode L.E.D. DOT Matrix Display Wrinkle Guard Program Audio Alert on Times 0 toPreprogrammed Cycle Preview Diagnostics Reversing OptionProgram Locations Page Preprogrammed Locations for Custom Drying Operating Sequence Operating InstructionsPage Page MAN Operating Notes Fire Suppression System F.S.S. Theory of Operation System Reset Fire Suppression System F.S.S. Valve Check Page E.D. Display Operating Status D. Display Messages Introduction to Programming Programming InstructionsPage START/ENTER STOP/CLEAR Programming Flowcharts Phase Menu Programming Procedure Page Auto Reverse Mode On OFF Espanol Selecting Languages0SELECT Language English Select Model Dryer SetupSelecting a Dryer Model Select System Parameters Electric Reversing GAS ReversingGAS REVERSING, Electric REVERSING, Steam REVERSING, GAS NON Steam NON-REVERSING Selecting the System Temperature Enter Lint Cleaning Frequency 1 to 10 Hours DEG FDEG C Setting the Lint Cleaning Frequency Enter Audio Alert on Times 0 to Adjusting the Audio Alert On times System Temp Rotation Sensor Rotation Sensor Press Enter to jump directly to the location Board Address 00 to ZZ OFF Dryer Address To ZZ Auto Cycle Time OUT to 99 Minutes Auto Cycle Time Out Enter Audio Alert on Times 0 to Rotation Sensor System Temp Enter Lint Cleaning Frequency 1 to 10 Hours Auto Cycle Time OUT To 99 Minutes Adjusting Reversing Spin Time and Stop Time Reversing Setup Enter Spin Time 30 to 120 SecondsEnter Stop Time 5 to 10 Seconds Press the up arrow key to increment Wrinkle Guard Audio Alert Setup Wrinkle Guard Audio Alert Wrinkle Guard Setup Steam Injection Setup Wrinkle Guard Setup Steam Injection Setup Cycle Enter 1ST on Time Enter 1ST OFF Time 511 to 000 First time adjustment is Minutes mm Enter 2ND on Time Program 0-40 Cycles Enter 3RD on Time Program System Cycles Parameters Programming a F Cycles or 0 40 Cycles Auto Reverse ModeSelect a F KEY Select Cycle Type Time Not AvailableEnter DRY Temp OFF Not Available Enter Dryness Level DRYEnter Stop Time To 10 Seconds Enter Cycle Adjustment DRY or Extra Extra DRYEnter DRY Time 0 to 99 Minutes Enter Cool Down Time 0 to 99 Minutes Controlled Cool Down Enter Cool Down Enter Cool Down Temp 70 to 100 ºF Steam Injection Cycle Enter 1ST on Time 511 to From Previous Enter 2ND on Time Enter 3RD on Time Restoring Factory Default Settings Enter Password Confirm Defaults YES Defaults SET Default Settings Cycle 0-40 Parameters Programs Preset by the Factory Cycle A-F Parameters Programs Preset by the Factory Preprogrammed Cycles Fixed Parameters System Parameters Program Locations Gas Standards Diagnostic L.E.D. Display Fault MessagesPage Page Page S.S. Diagnostic Conditions Brhl RED L.E.D INPUT/OUTPUT I/O Board L.E.D. Indicators Keyboard Touch PAD Layout Customer Custom Parameter Settings Auto Programmed Cycle Page ADC Part No 08/19/08