Specifications | American Power Conversion AP9207 specification

Specifications continued

Advanced port The Advanced port of Share-UPS has the same limitations pin assignments and capabilities as the Basic port (see “Basic port pin

assignments,” on page 54). The following additional limita- tions and capabilities apply to the Advanced port:

•Applying a momentary (approximately 1 second) high RS-232 level to Pin 7 turns on the UPS and its loads. A momentary low RS-232 level turns off the UPS and its loads. Pin 7 should normally be uncon- nected. This signal is passed through Share-UPS.

•DC operating voltage is available on Pin 8 of the Advanced port. This voltage may be the UPS battery voltage or the voltage from an external adapter, whichever is greater.

Continued on next page

Page 62

Image 62

American Power Conversion AP9207 manual Specifications

Contents

Share-UPS Thank You Contents Setting Up Share-UPS Using the Share-UPS Menus Product Information Introduction Can delay shutdown of the UPS until all servers have Following list shows some of the features of ShareSupports advanced or simple signaling on its UPS and Share-UPS. See Using the Share-UPS On next Cable supplied with your APC UPS Product Description On page 10. For Basic port specifications, see Basic port Tery and Low Battery conditions in the UPS. For furtherInformation see Simple versus smart signaling Table Pin assignments, on Product Description If the LED Is… Then Share-UPS… Labeled… Product Description Communication Types Simple Signaling Smart SignalingKey Concepts Key Concepts If the UPS had previously been connected using Smart signaling UPS on page 23, when it may force a Low Battery signal Low Battery condition at the UPS. Share-UPS generates aTo the configured shutdown mode see Configuring Share An On Battery signal, causing the servers to shut down Key Concepts Installing Multiple Accessories Interface Expander Accessory slot with the higher numberAccessory Priority Position Share-UPS unit and the master server, you can purchase an AP9604. For installation instructions, refer to the userIf you need additional SmartSlot capacity between APC Expansion Chassis AP9600 or Triple Chassis Installing Share-UPS Mounting Share-UPS NetShelter Figure Mounting Share-UPS on a wall Figure If using Optional Power input see Optional Connecting Share-UPSConfiguring Share-UPS, on If daisy-chaining multiple Share-UPS units An Expansion Chassis, is already using Ate cable. See Choosing simple signalingIf an accessory, such as Measure-UPS II or Share-UPS use simple signaling for moni Configuring Share-UPS Behavior Confirmed shutdown mode Effect Shutdown delay, go to ConfigurationEvent Down delay for a time longer than Share-UPS timerSetting. Otherwise, if the power returns after Actions and select UPS On Battery from the Event If you want to change Share-UPS settings Com If configuring multiple Share-UPS units repeat Troubleshooting on Steps in the order given. If Share-UPS fails this test, see Using the Share-UPS Menus Using the Management Port Password-protected menu interface allows you to view Using a dumb terminal or a computer and terminal emulaTion software, you can access the UPS remotely. Load, battery conditions, and current UPS status As possible. See Share-UPS Settings Nected, after three unsuccessful passwordFor security, change the password as soon Characters long, and is case-sensitive Main Menu Main menu The following figure shows the Main menu. Figure Main menu only if Share-UPS has detected an APC Measure-UPS environmental monitoring accessoryUPS accessory For a description of the Measure-UPS Status screen Description Behavior Following table describes the items that appear onMain menu UPS Status Display Connected UPS, output and load readings, battery informaAccess the UPS Status display, type s from the Main menu Following figure shows the UPS Status display UPS Status Display Definitions Waiting to Power Load Status display, type c from the Main menu Tions on demand through Share-UPS. To access the UPSUPS Control Menu Following figure shows the UPS Control menu UPS Control menu It is connected to the UPS Following figure shows the Share-UPS Settings menu Share-UPS Settings MenuShare-UPS Settings menu allows you to configure Menu, type d from the Main menu Share-UPS Settings menu Definitions Paging Setup Menu Site IDspaceevent code Ured for paging During a utility power outage when Share-UPS is configFollowing figure shows a typical sequence of events That you may include in your dial string see Share-UPS Following figure shows the Paging Setup menuFollowing table lists some common modem commands Information, see the documentation supplied with Paging Setup menu Setting Description Paging Setup Menu Definitions Warranty Information Exclusion of implied warranties therefore, the aforesaid Claims by third parties, or otherwise. This warranty givesPurpose. Some jurisdictions do not permit limitation or Specifically, APC is not liable for any costs, such as lost Troubleshooting Trouble Shooting Trouble Shooting Table Persists, follow this procedure For problems not covered in the troubleshooting chart seeTroubleshooting on page 26, or if the problem Material authorization RMA number Life-Support Policy Specifications Assignments Specifications Normally Open Data bits with 1 start bit, 1 stop bit, and no parity Communications port. The port is configured as data termiManagement port is a standard 9-pin RS-232 serial Management port pin assignments are listed in the fol Share-UPS Following table shows the product specifications forSpecification Product Specifications Symbols Index Index Re-Boot All Servers Y, Z Page W. a p c c . c o m