Ured for paging | American Power Conversion AP9207 guide

Paging Setup Menu continued

Typical paging	The following figure shows a typical sequence of events
sequence:	during a utility power outage when Share-UPS is config-
Table 10	ured for paging.

		Power failure occurs:
		UPS goes on battery


		Share-UPS transmits
		modem command string


		Pager displays Site ID
		and Event Code for
		UPS On Battery


		Power is restored:
		UPS goes on line


		Share-UPS transmits
		modem command string


		Pager displays Site ID
		and Event Code for
		UPS On Line


		Continued on next page

43

Image 49

American Power Conversion AP9207 manual Following figure shows a typical sequence of events, Ured for paging

Contents

Share-UPS Thank You Contents Setting Up Share-UPS Using the Share-UPS Menus Product Information Introduction Supports advanced or simple signaling on its Following list shows some of the features of ShareCan delay shutdown of the UPS until all servers have UPS and Share-UPS. See Using the Share-UPS On next Cable supplied with your APC UPS Product Description Information see Simple versus smart signaling Table Tery and Low Battery conditions in the UPS. For furtherOn page 10. For Basic port specifications, see Basic port Pin assignments, on Product Description If the LED Is… Then Share-UPS… Labeled… Product Description Key Concepts Simple Signaling Smart SignalingCommunication Types Key Concepts Smart signaling If the UPS had previously been connected using To the configured shutdown mode see Configuring Share Low Battery condition at the UPS. Share-UPS generates aUPS on page 23, when it may force a Low Battery signal An On Battery signal, causing the servers to shut down Key Concepts Installing Multiple Accessories Accessory Priority Position Accessory slot with the higher numberInterface Expander If you need additional SmartSlot capacity between AP9604. For installation instructions, refer to the userShare-UPS unit and the master server, you can purchase an APC Expansion Chassis AP9600 or Triple Chassis Installing Share-UPS Mounting Share-UPS NetShelter Figure Mounting Share-UPS on a wall Figure Configuring Share-UPS, on Connecting Share-UPSIf using Optional Power input see Optional If daisy-chaining multiple Share-UPS units If an accessory, such as Measure-UPS II or Ate cable. See Choosing simple signalingAn Expansion Chassis, is already using Share-UPS use simple signaling for moni Configuring Share-UPS Behavior Confirmed shutdown mode Effect Setting. Otherwise, if the power returns after Down delay for a time longer than Share-UPS timerShutdown delay, go to ConfigurationEvent Actions and select UPS On Battery from the Event If configuring multiple Share-UPS units repeat If you want to change Share-UPS settings Com Steps in the order given. If Share-UPS fails this test, see Troubleshooting on Using the Management Port Using the Share-UPS Menus Tion software, you can access the UPS remotely. Using a dumb terminal or a computer and terminal emulaPassword-protected menu interface allows you to view Load, battery conditions, and current UPS status For security, change the password as soon Nected, after three unsuccessful passwordAs possible. See Share-UPS Settings Characters long, and is case-sensitive Main menu The following figure shows the Main menu. Figure Main Menu UPS accessory Measure-UPS environmental monitoring accessoryMain menu only if Share-UPS has detected an APC For a description of the Measure-UPS Status screen Main menu Following table describes the items that appear onDescription Behavior Access the UPS Status display, type s from the Main menu Connected UPS, output and load readings, battery informaUPS Status Display Following figure shows the UPS Status display UPS Status Display Definitions Waiting to Power Load UPS Control Menu Tions on demand through Share-UPS. To access the UPSStatus display, type c from the Main menu Following figure shows the UPS Control menu It is connected to the UPS UPS Control menu Share-UPS Settings menu allows you to configure Share-UPS Settings MenuFollowing figure shows the Share-UPS Settings menu Menu, type d from the Main menu Share-UPS Settings menu Definitions Site IDspaceevent code Paging Setup Menu Following figure shows a typical sequence of events During a utility power outage when Share-UPS is configUred for paging Following table lists some common modem commands Following figure shows the Paging Setup menuThat you may include in your dial string see Share-UPS Information, see the documentation supplied with Setting Description Paging Setup menu Paging Setup Menu Definitions Warranty Information Purpose. Some jurisdictions do not permit limitation or Claims by third parties, or otherwise. This warranty givesExclusion of implied warranties therefore, the aforesaid Specifically, APC is not liable for any costs, such as lost Troubleshooting Trouble Shooting Trouble Shooting Table Troubleshooting on page 26, or if the problem For problems not covered in the troubleshooting chart seePersists, follow this procedure Material authorization RMA number Life-Support Policy Specifications Assignments Specifications Normally Open Management port is a standard 9-pin RS-232 serial Communications port. The port is configured as data termiData bits with 1 start bit, 1 stop bit, and no parity Management port pin assignments are listed in the fol Specification Following table shows the product specifications forShare-UPS Product Specifications Index Symbols Index Re-Boot All Servers Y, Z Page W. a p c c . c o m