American Standard CH530 Chiller, Feature Settings

CDHF-SVU01C-EN

44

Operator

Interface

Chiller

Description Resolution or (Enumerations), Default Units

1. Front Panel Control Type (Chilled Water, Hot Water), Chilled Water Enum

2. Front Panel Chilled Water Setpt (3)

+ or – XXX.X Temperature

3. Front Panel Hot Water Setpt (3)

+ or – XXX.X Temperature

4. Front Panel Current Limit Setpt XXX (4) Percent RLA

5. Front Panel Base Load Cmd On/Auto enum

6. Front Panel Base Load Setpt XXX Percent

7. Front Panel Ice Build Cmd On/Auto Enum

8. Front Panel Ice Termn Setpt XXX.X Temperature

9. Ice to Normal Cool Timer Setpt (0-10), 5 min Minutes

10. Differential to Start XXX.X Temperature

11. Differential to Stop XXX.X Temperature

12. Setpoint Source *(BAS/Ext/FP, Ext/ Front Panel, Front Panel),

BAS/Ext/FP Default Enum

*Follows hierarchy of selection from left to right (except for ice building which is “OR” logic).

Feature Settings

Description Resolution or (Enumerations), Default Units

1. Chilled Water Reset (Constant, Outdoor, Return, Disable), Disable Enum

2. Return Reset Ratio XXX Percent

3. Return Start Res et XXX.X Temperature

4. Return Maximum Reset XXX.X Temperature

5. Outdoor Reset Ratio XXX Percent

6. Outdoor Start Reset XXX.X Temperature

7. Outdoor Maximum Reset XXX.X Temperature

8. Ext Chilled Water Setpoint (Enable, Disable), Disable Enum

9. Ext Current Limit Setpoint (Enable, Disable), Disable Enum

10. Ice Building Feature Enable (Enable, Disable), Disable Enum

11. Ext Base Loading Setpoint (Enable, Disable), Disable Enum

Contents

Main Warnings and Cautions Contents Typical Product Description Block Unit Nameplate Literature change About this manual Page Page Commonly Used Acronyms Figure 1. General Duplex unit components - front view Page Cooling Cycle Page Page Page Figure 7. Sequence of operation overview. Figure 8. CDHE/F/G sequence of operation: auto to running Figure 9. CDHE, CDHF, and CDHG sequence of operation: running Page Figure 12. CDHF/G sequence of operation: lead 1/lag 2 Figure 13. CDHE/F/G sequence of operation: lead 2 lag 1 Figure 14. CDHF/G sequence of operation: equalize starts and hours Figure 15. CDHF/G sequence of operation: combined start Page Oil and Refrigerant Pump Surface Temperatures! Page Base Loading Control Algorithm: Page Ice Machine Control Figure 18. Sequence of operation: ice making: running to ice making Figure 19. Sequence of operation: ice making: stopped to ice to ice building complete Hot Water control Unit Control Panel (UCP) Control Panel Devices and Unit Mounted Devices Figure 20. Left control panel Unit Control Panel (UCP) Tracer CH530 Chiller Controller Figure 21. DynaView main processor Page Page A general description of the top level modes is show in the following table. Figure 22 Figure 23 Page Main Screen Data Fields Table Diagnostic Screen Page Page Report Menu Report name: System Evaporator Report name: Circuit Evaporator Report name: System Condenser Report name: Circuit Condenser Report name: System ASHRAE Chiller Log Report name: Circuit ASHRAE Chiller Log Historic Diagnostics Log Page Chiller Feature Settings System Mode Overrides Circuit Mode Overrides (0 to disable) Purge Display Settings { Page Page Page Page Control Panel Internally mounted devices Interprocessor Communication Inter Processor Communications IPC3 Page Page Control Panel Devices Head Relief Request Output Maximum Capacity Relay Compressor Running Relay Machine Shutdown Manual Reset (MMR) Chilled and Condenser Water Flow Interlock Circuits Refrigerant Monitor Input 1A17 Page CDRP Refrigerant Pressure Output Option 1A15: Figure 25. Condenser pressure based output Page GBAS (Generic Building Automation System) Figure 27. Voltage versus percent RLA External Chilled Water Setpoint (ECWS) External Current Limit Setpoint WPSR (WFC Water Pressure Sensing Option) Module Characteristics Page Recommended Length to Run external Output signals Unit mounted devices Page Page Electrical Sequence UCP and Wye-Delta Starter Control Circuits Page Page Figure 24. Test and start timing sequence Page Momentary Power Loss (MPL) Protection. and starter module remain powered) Figure 29. Sequence of operation: momentary power loss, (DynaView Current Overload Protection Figure 30. Overload trip time versus percent RLA Current Limit Protection Reverse Rotation Protection Differential to Start or Stop SoftLoading Evaporator Limit Leaving Water Temperature Cutout Low Refrigerant Temperature Cutout Page Condenser Limit Restart Inhibit Page Page Controls Chilled Water Reset (CWR) Return Water = Maximum Reset. Outdoor Air Temperature Where Constant Return Reset Ratio: Figure 32. Outdoor air temperature versus degrees of reset Page Page Page Unit Start-Up Procedures Unit Startup Seasonal Unit Start-Up Unit Startup Live Electrical Components! Toxic Hazards! Unit Shutdown Unit Shutdown Procedures Seasonal Unit Shutdown Oil Pump Heater Operation! Trouble Analysis Moisture Contamination! Hazardous Voltage w/Capacitors! Normal Chiller Operating Characteristics Weekly Maintenance Every 6 Months Every 3 Months Off-Season Maintenance Annual Maintenance Oil Maintenance Compressor Oil Change Oil Change Procedure Heater Damage! Oil Maintenance Replacing Oil Filter Other Maintenance Requirements Oil Supply System Problems! Hazardous Voltage w/ Capacitors! Figure 37. Rotary valve in drain position Refrigerant Charge Contains Refrigerant! Recovery and Recycle Connections Leak Testing Figure 38. Typical chemical cleaning setup Cleaning the Condenser Proper Water Treatment! Unit Corrosion Damage! Cleaning the Evaporator Control Settings and Adjustments Purge System Unit Preparation Contains Refrigerant! Live Electrical Components!