NI-2000 Specifications, Rear | AMX NXI-x000 Series instruction

Introduction

NI-2000 Specifications

The front panel LEDs (FIG. 1) are grouped by control type and are labeled according to their corresponding port (connector) numbers on the rear of the unit. The back of the unit contains three RS-232/422/485, one Relay, one IR/Serial and one I/O connectors. In addition, this unit provides an ID pushbutton, AXlink LED, and other related connectors. FIG. 2 shows the front and rear of the NI-2000.

FIG. 1 NI-2000 NetLinx Integrated Controller (front view)

			RS-232/422/485 TX/RX LEDs (red/yellow)
Link/Active-Status-Output-Input			Relay LEDs (red)
			IR/Serial LEDs (red)
			I/O LEDs
			(yellow)
Front
			ICSNet (2)	AXlink LED
Rear	RS-232/422/485 (Ports 1-3)		ICSHub Out	(green)
				AXlink
Relays	IR/Serial (Ports 5-8)		Ethernet	port
Relays	IR/Serial (Ports 5-8)		Ethernet
(Port 4)
	I/O (Port 9)	Program	DIP	PWR
	I/O (Port 9)	Program	switch	PWR
		port	switch
		port
			ID Pushbutton
FIG. 2 NI-2000 front and rear panel components

2	NI-2000, NI-3000, NI-4000 Hardware Reference Guide

Image 6

AMX NXI-x000 Series manual NI-2000 Specifications, Rear

Contents

NXI-x000 Series AMX Limited Warranty and Disclaimer Table of Contents Table of Contents NetLinx Integrated Master Controller Features Introduction NI-2000 Specifications Rear NI-2000 Specifications Rear Panel ConnectorsFront Panel Components Surge damage NI-2000 Specifications NI-3000 Specifications NI-3000 NetLinx Integrated Controller front view NI-3000 Specifications Surge damage NI-3000 Specifications NI-4000 Specifications NI-4000 NetLinx Integrated Controller front view NI-4000 Specifications Rear Panel Connectors Guide for details Related Documents Installation and Upgrading Installing NetLinx Control Cards NI-4000 Only Setting the NetLinx Control Card Addresses NI-4000 Only DevicePortSystem DPSPosition Removing NetLinx Control Cards NI-4000 Only Compact Flash UpgradesOptional Compact Flash Upgrades Product Name Description Installation of Compact Flash Upgrades Installing Into An Equipment Rack Closing and Securing the Outer Housing Install screws Bracket Rack Mounting Holes Program Run Disable PRD Mode Setting the Configuration DIP Switch for the Program PortBaud Rate Settings Baud Rate Settings on the Configuration DIP Switch Working With the Configuration DIP Switch Setting the CardFrame DIP Switch NI-4000 OnlyProgram Port Connections and Wiring Program Port, Pinouts, and Signals Modes and LED Blink Patterns Modes and Front Panel LED Blink PatternsPort Assignments and Functionality NI-2000 Port Assignments Wiring Guidelines NI-2000 @ 700 mA Wiring GuidelinesWiring length guidelines Wiring Guidelines NI-3000 & NI-4000 @ 900 mA Preparing Captive Wires Wiring a Power ConnectionUsing the 4-Pin Mini-Phoenix Connector For Data and Power DB9 Device Port Connections and Wiring RS-232 RS-422 RS-485 ICSNet RJ-45 Signals ICSNet Port Connections and WiringRS-232/422/485 Device Port Wiring Specifications RJ-45 Pinout Information EIA/TIA 568 B ICSHub OUT Pinouts and Signals ICSHub OUT Port Connections and WiringRelay Port Connections and Wiring Relay Connections Input/Output I/O Port Connections and Wiring Port Wiring Specifications NI-4000 and NI-3000Port Wiring Specifications NI-2000 IR/Serial Connector Wiring Specifications per Port IR/Serial Port Connections and WiringNetLinx Control Card Slot Connector NI-4000 only Signal Function Pin Signals Connections Pairing Color Ethernet/RJ-45 Port Connections and WiringEthernet RJ-45 Pinouts and Signals Ethernet LEDs Ethernet Ports Used By the Integrated Controller Ethernet Port DescriptionsPort type Description Standard Port # Page It’s Your World Take Control