NI-4000 Specifications | AMX NXI-x000 Series guide

Introduction

NI-4000 Specifications

The front LEDs (FIG. 5) are grouped by control type, and are labeled according to their corresponding port (connector) numbers on the rear of the unit. The back of the this unit contains RS-232/422/485, Relay, IR/Serial and I/O connectors. In addition, this unit provides an ID pushbutton, AXlink LED, NetLinx Card slots, and other related connectors. FIG. 6 shows the front and rear of the NI-4000.

FIG. 5 NI-4000 NetLinx Integrated Controller (front view)

Link/Active-Status-Output-Input

RS-232/422/485 TX/RX LEDs (red/yellow)

Relay LEDs (red)

IR/Serial LEDs (red)

NetLinx

Card

slots

(1-4)

Front

I/O LEDs (yellow)

		RS-232/422/485 (Ports 1-7)			ICSNet (2)		AXlink LED
	Rear	RS-232/422/485 (Ports 1-7)			ICSHub Out		(green)
	Rear				ICSHub Out		(green)
							AXlink
	Relays					Ethernet	port
	Relays	I/O (Port 17)	IR/Serial (Ports 9-16)
	(Port 8)

					DIP
					DIP
					switch
				Program port
							PWR
	CardFrame DIP	Slot 1-4 connectors
	switch	Slot 1-4 connectors		ID Pushbutton
	switch			ID Pushbutton
	FIG. 6 NI-4000 front and rear panel components

10	NI-2000, NI-3000, NI-4000 Hardware Reference Guide

Image 14

AMX NXI-x000 Series manual NI-4000 Specifications, NI-4000 NetLinx Integrated Controller front view

Contents

NXI-x000 Series AMX Limited Warranty and Disclaimer Table of Contents Table of Contents NetLinx Integrated Master Controller Features Introduction NI-2000 Specifications Rear Front Panel Components NI-2000 SpecificationsRear Panel Connectors Surge damage NI-2000 Specifications NI-3000 Specifications NI-3000 NetLinx Integrated Controller front view NI-3000 Specifications Surge damage NI-3000 Specifications NI-4000 Specifications NI-4000 NetLinx Integrated Controller front view NI-4000 Specifications Rear Panel Connectors Guide for details Related Documents Installation and Upgrading Installing NetLinx Control Cards NI-4000 Only Position Setting the NetLinx Control Card Addresses NI-4000 OnlyDevicePortSystem DPS Removing NetLinx Control Cards NI-4000 Only Compact Flash UpgradesOptional Compact Flash Upgrades Product Name Description Installation of Compact Flash Upgrades Installing Into An Equipment Rack Closing and Securing the Outer Housing Install screws Bracket Rack Mounting Holes Program Run Disable PRD Mode Setting the Configuration DIP Switch for the Program PortBaud Rate Settings Baud Rate Settings on the Configuration DIP Switch Working With the Configuration DIP Switch Setting the CardFrame DIP Switch NI-4000 OnlyProgram Port Connections and Wiring Program Port, Pinouts, and Signals Modes and LED Blink Patterns Modes and Front Panel LED Blink PatternsPort Assignments and Functionality NI-2000 Port Assignments Wiring Guidelines NI-2000 @ 700 mA Wiring GuidelinesWiring length guidelines Wiring Guidelines NI-3000 & NI-4000 @ 900 mA Using the 4-Pin Mini-Phoenix Connector For Data and Power Preparing Captive WiresWiring a Power Connection DB9 Device Port Connections and Wiring RS-232 RS-422 RS-485 ICSNet RJ-45 Signals ICSNet Port Connections and WiringRS-232/422/485 Device Port Wiring Specifications RJ-45 Pinout Information EIA/TIA 568 B ICSHub OUT Pinouts and Signals ICSHub OUT Port Connections and WiringRelay Port Connections and Wiring Relay Connections Port Wiring Specifications NI-2000 Input/Output I/O Port Connections and WiringPort Wiring Specifications NI-4000 and NI-3000 IR/Serial Connector Wiring Specifications per Port IR/Serial Port Connections and WiringNetLinx Control Card Slot Connector NI-4000 only Signal Function Pin Signals Connections Pairing Color Ethernet/RJ-45 Port Connections and WiringEthernet RJ-45 Pinouts and Signals Ethernet LEDs Port type Description Standard Port # Ethernet Ports Used By the Integrated ControllerEthernet Port Descriptions Page It’s Your World Take Control