Manuals / AMX / Computer Equipment / Network Card

AMX NXI-x000 Series manual Related Documents, NI-4000 Specifications Cont, Introduction

Models: NXI-x000 Series

1 38

Download 38 pages 51.77 Kb

Page 18

Related Documents

Introduction

NI-4000 Specifications (Cont.)

Other AMX Equipment:

•2-pin 3.5 mm mini-Phoenix male connector (41-5026)

•CC-NIRC IR cables (FG10-000-11)

•CC-NSER IR/Serial cables (FG10-007-10)

•CSB Cable Support Bracket (FG517)

•NCK, NetLinx Connector Kit (FG2902)

•STS, Serial To Screw Terminal (FG959)

•Upgrade Compact Flash (factory programmed with firmware): NXA-CFNI64M - 64 MB compact flash card (FG2116-31) NXA-CFNI128M - 128 MB compact flash card (FG2116-32) NXA-CFNI256M - 256 MB compact flash card (FG2116-33) NXA-CFNI512M - 512 MB compact flash card (FG2116-34) NXA-CFNI1G - 1 GB compact flash card (FG2116-35)

•NXC cards (see the Card Slot section (page 11) of this Specification table for more detailed information)

Related Documents

For information on using the on-board Web Console, as well as NetLinx send commands and terminal communications to configure the NI Controllers, refer to the NetLinx Integrated Controller WebConsole & Programming Guide.

All product documentation is available to view or download from www.amx.com.

14	NI-2000, NI-3000, NI-4000 Hardware Reference Guide

Image 18

AMX NXI-x000 Series manual Related Documents, NI-4000 Specifications Cont, Introduction

Contents

NetLinx Integrated Controllers NI-2000, NI-3000, NI-4000 NXI-x000 SeriesHardware Reference Guide NetLinx Integrated ControllersAMX Limited Warranty and Disclaimer Connections and Wiring Table of ContentsInstallation and Upgrading IntroductionNetLinx Control Card Slot Connector NI-4000 only Input/Output I/O Port Connections and WiringIR/Serial Port Connections and Wiring Ethernet/RJ-45 Port Connections and WiringIntroduction NI-2000 Specifications FrontRear Introduction NI-2000 SpecificationsRear Panel Connectors Front Panel ComponentsIntroduction NI-2000 Specifications ContRear Panel Connectors Cont surge damageSPD speed - Yellow LED lights On when the connection speed is NI-2000 Specifications ContRear Panel Connectors Cont Mbps and turns Off when the speed is 10 MbpsNI-3000 Specifications Introduction NI-3000 SpecificationsRear Panel Connectors Front Panel ComponentsIntroduction NI-3000 Specifications ContRear Panel Connectors Cont Refer to the NetLinx Integrated Controller WebConsole & ProgrammingIntroduction NI-3000 Specifications ContRear Panel Connectors Cont NI-2000, NI-3000, NI-4000 Hardware Reference GuideNI-4000 Specifications FIG. 5 NI-4000 NetLinx Integrated Controller front viewFIG. 6 NI-4000 front and rear panel components Front Panel Components NI-4000 SpecificationsIntroduction NI-2000, NI-3000, NI-4000 Hardware Reference GuideIntroduction NI-4000 Specifications ContRear Panel Connectors surge damageIntroduction NI-4000 Specifications ContRear Panel Connectors Cont Refer to the NetLinx Integrated Controller WebConsole & ProgrammingIntroduction Related DocumentsNI-4000 Specifications Cont NI-2000, NI-3000, NI-4000 Hardware Reference GuideInstallation and Upgrading Installing NetLinx Control Cards NI-4000 OnlySetting the NetLinx Control Card Addresses NI-4000 Only DevicePortSystem DPSAccessing The Internal Components On An Integrated Controller Compact Flash UpgradesRemoving NetLinx Control Cards NI-4000 Only The NI-2000 and NI-3000 have six screws on top and three on each sideInstallation of Compact Flash Upgrades 5. Remove the upgrade card from it’s anti-static bagInstalling Into An Equipment Rack Closing and Securing the Outer Housing7. Apply power to the unit to complete the installation Baud Rate Settings Connections and WiringSetting the Configuration DIP Switch for the Program Port Program Run Disable PRD ModeSetting the CardFrame DIP Switch NI-4000 Only Program Port Connections and WiringWorking With the Configuration DIP Switch Connections and Wiring Modes and Front Panel LED Blink PatternsPort Assignments and Functionality Modes and LED Blink PatternsWiring length guidelines Wiring GuidelinesAXlink Port and LED 1 blink per second - Normal operationWiring a Power Connection Preparing Captive Wires1. Strip 0.25 inch 6.35 mm of insulation off all wires Using the 4-Pin Mini-Phoenix Connector For Data and PowerDB9 Device Port Connections and Wiring Using the 4-pin Mini-Phoenix Connector For Data With External PowerICSNet RJ-45 Signals ICSNet Port Connections and WiringRS-232/422/485 Device Port Wiring Specifications Connections and WiringICSHub OUT Port Connections and Wiring Relay Port Connections and WiringRelay Connections Input/Output I/O Port Connections and Wiring IR/Serial Port Connections and Wiring NetLinx Control Card Slot Connector NI-4000 onlyEthernet/RJ-45 Port Connections and Wiring Ethernet LEDsEthernet Port Descriptions Connections and WiringEthernet Ports Used By the Integrated Controller Port typeConnections and Wiring NI-2000, NI-3000, NI-4000 Hardware Reference GuideIt’s Your World - Take Control