Symbols, Self Test | Anritsu S251C manual

Chapter 2 Functions and Operations

Symbols

Table 2-1provides a listing of the symbols used as condition indicators on the LCD display.

Table 2-1.LCD Icon Symbols

Icon

HOLD

dx

T

Symbol

Site Master is in Hold for power conservation. To resume sweeping, press the RUN/HOLD key. After 10 minutes without a key press, the Site Master will automatically activate the power conservation mode.

Integrator Failure. Intermittent integrator failure may be caused by inter- ference from another antenna. Persistent integrator failure indicates a need to return the Site Master to the nearest Anritsu service center for repair.

Lock fail indication. Check battery. (If the Site Master fails to lock with a fully charged battery, call your Anritsu Service Center.)

When calibration is performed, the Site Master stores the ambient temper- ature. If the temperature drifts outside the specified range, this indicator will flash. A recalibration at the current temperature is recommended.

Indicates the remaining charge on the battery. The inner white rectangle grows longer as the battery charge depletes.

Indicates internal data processing.

CAL ON The Site Master has been calibrated.

CALL OFF The Site Master has not been calibrated.

Self Test

At turn-on, the Site Master runs through a series of quick checks to ensure the system is functioning properly. Note that the battery voltage and temperature are displayed in the lower left corner below the self test message. If the battery is low, or if the ambient temper- ature is not within the specified operational range, Self Test will fail. If Self Test fails and the battery is fully charged and the Site Master is within the specified operating temperature range, call your Anritsu Service Center.

2 - 15

Image 30

Anritsu S251C manual Symbols, Self Test

Contents

Site Master Model S251C Antenna Cable Analyzer Page Warranty Page Table of Contents Cable & Antenna Analysis Iii/iv Standard Accessories IntroductionDescription Optional Accessories Options Performance Specifications Description Site Master Performance Specifications 2 Preventive Maintenance ESD Precautions Annual Verification Anritsu Service Centers Test Connector Panel Chapter Functions and Operations Front Panel Overview Active Function Block Soft Keys Function Hard Keys Mode Keypad Hard Keys Clear Auto Soft Keys MODE=FREQ FREQ/DIST Softkeys MODE=DTF FREQ/DIST Softkeys Functions and Operations Amplitude Power Monitor Menu Option MODE=POWER Monitor Softkeys RF Source Menu MODE=RF Source Softkeys Limit Segment 1 Segment SYS Symbols Self Test Error Codes Self Test Errors Range Errors ERRORD2 Charging the Battery in the Site Master Battery InformationCharging a New Battery Charging the Battery in the Optional Charger Battery Charge Indicator Battery Life Important Battery Information Power On Procedure Chapter Getting Started Select the Frequency or Distance Calibration Calibration Procedure Single Port Calibration Calibration Procedure Dual Port RF in Test Port RF OUT Test Port Setting the Scale Save and Recall a SetupSave and Recall a Display Recalling a Display Set the Distance and Cable Type Changing the UnitsChanging the Display Language Printing Printing a Screen Printer Switch Settings Printer Using the Soft Carrying Case Using the Site Master Soft Carrying Case One Port Measurements Line Sweep Fundamentals Information Required for a Line Sweep Measurements Typical Line Sweep Test Procedures System Return Loss Measurement 2is an example of a typical system return loss trace Procedure Cable Loss Mode Insertion Loss Measurement Type Attenuation dB/ft Length ft = Loss dB Procedure Return Loss Mode Distance-To-Fault DTF Transmission Line Test Procedure DTF-Return Loss Mode Procedure DTF-SWR Mode Antenna Subsystem Return Loss Test Vswr Two Port Measurements Introduction TMA Measurements TMA-S TMA Gain Measurement After Calibration TMA-DD 12. TMA-DD Gain Measurement TMA-D 14. TMA-D Gain Measurement Antenna to Antenna Isolation 15. System Isolation Quency settings for common systems Antenna-to-Antenna Isolation Measurement 21/4-22 Features System Requirements Installation Communication Port Setting Using Software Tools Interface Cable InstallationDownloading Traces from the Site Master Plot Capture Plot Properties Trace Overlay or Plot Overlay Saving Traces Custom Cable List Saving a Plot to a Spreadsheet Creating a Database Printing Formats Coaxial Cable Technical Data Appendix a Reference Data Appendix a Reference Data A-4 Appendix B Windowing Examples Appendix B Windowing B-4