Printing a Screen | Anritsu S251C specs

Chapter 3 Getting Started

Printing

Printing is accomplished by selecting an available printer and pressing the print key as de- scribed below. Refer to the particular printer operating manual for specific printer settings.

Printing a Screen

Step 1. Connect the printer as shown in Figure 3-4.

Site Master S251C

		ESCAPE
1	2	CLEAR
START	AUTO
CAL	SCALE
3	4
SAVE	RECALL
SETUP	SETUP
5	6
LIMIT	MARKER
7	8	ENTER
7	8
SAVE	RECALL	RUN
DISPLAY	DISPLAY	HOLD
9	0	+/-
ON	PRINT	SYS
OFF	.	SYS
	.

MODE

FREQ/DIST

AMPLITUDE

SWEEP

SEIKO

PRINTER

SERIAL CABLE 2000-1012

HP 350

DESKJET

SERIAL-TO-PARALLEL INTERFACE CABLE 2000-753

Figure 3-4-. Site Master Printer Setup

Step 2. Obtain the desired measurement display

Step 3. Press the SYS key and the OPTIONS soft key (Figure 3-5) .

OPTIONS

Site Master S251C

OPTIONS

CLOCK

SELF TEST

STATUS

		ESCAPE
1	2	CLEAR
1	2
START	AUTO
CAL	SCALE
3	4
SAVE	RECALL
SETUP	SETUP
5	6
LIMIT	MARKER
7	8	ENTER
7	8
SAVE	RECALL	RUN	SYS
DISPLAY	DISPLAY	HOLD
9	0	+/-
ON	PRINT	SYS
OFF	.	SYS
OFF

MODEFREQ/DIST AMPLITUDE SWEEP

Figure 3-5-. SYS Key and OPTIONS Soft Key

3-8

Image 43

Anritsu S251C manual Printing a Screen

Contents

Site Master Model S251C Antenna Cable Analyzer Page Warranty Page Table of Contents Cable & Antenna Analysis Iii/iv Introduction Standard AccessoriesDescription Options Optional Accessories Performance Specifications Description Site Master Performance Specifications 2 ESD Precautions Preventive Maintenance Annual Verification Anritsu Service Centers Chapter Functions and Operations Test Connector Panel Active Function Block Soft Keys Front Panel Overview Mode Function Hard Keys Clear Keypad Hard Keys Auto MODE=FREQ FREQ/DIST Softkeys Soft Keys MODE=DTF FREQ/DIST Softkeys Functions and Operations Amplitude MODE=POWER Monitor Softkeys Power Monitor Menu Option MODE=RF Source Softkeys RF Source Menu Limit Segment 1 Segment SYS Self Test Symbols Self Test Errors Error Codes ERRORD2 Range Errors Charging the Battery in the Optional Charger Battery InformationCharging a New Battery Charging the Battery in the Site Master Battery Life Battery Charge Indicator Important Battery Information Chapter Getting Started Power On Procedure Calibration Select the Frequency or Distance Calibration Calibration Procedure Single Port RF in Test Port RF OUT Test Port Calibration Procedure Dual Port Save and Recall a Setup Setting the ScaleSave and Recall a Display Recalling a Display Changing the Units Set the Distance and Cable TypeChanging the Display Language Printing a Screen Printing Printer Printer Switch Settings Using the Site Master Soft Carrying Case Using the Soft Carrying Case Line Sweep Fundamentals One Port Measurements Measurements Information Required for a Line Sweep System Return Loss Measurement Typical Line Sweep Test Procedures 2is an example of a typical system return loss trace Insertion Loss Measurement Procedure Cable Loss Mode Type Attenuation dB/ft Length ft = Loss dB Procedure Return Loss Mode Procedure DTF-Return Loss Mode Distance-To-Fault DTF Transmission Line Test Procedure DTF-SWR Mode Antenna Subsystem Return Loss Test Vswr Introduction Two Port Measurements TMA-S TMA Measurements TMA Gain Measurement After Calibration TMA-DD 12. TMA-DD Gain Measurement TMA-D 14. TMA-D Gain Measurement 15. System Isolation Antenna to Antenna Isolation Antenna-to-Antenna Isolation Measurement Quency settings for common systems 21/4-22 System Requirements Features Communication Port Setting Installation Interface Cable Installation Using Software ToolsDownloading Traces from the Site Master Plot Properties Plot Capture Saving Traces Trace Overlay or Plot Overlay Saving a Plot to a Spreadsheet Custom Cable List Printing Formats Creating a Database Appendix a Reference Data Coaxial Cable Technical Data Appendix a Reference Data A-4 Examples Appendix B Windowing Appendix B Windowing B-4