TMA Measurements, Tma-S | Anritsu S251C specs

Chapter 4 Measurements

TMA Measurements

Required Equipment

Site Master Model S251C

Option 10A, Bias Tee

External Power Supply 40-115

Test Port Extension Cable, Anritsu 15NNF50-1.5C

N (m) to 716 (m) Adapters

Device Under Test

TMA-S

Procedure

Step 1. Connect the External Power Supply (40-115) to the Site Master.

Step 2. Turn on the Site Master and press the MODE key.

Step 3. Select INSERTION GAIN (–30 dBm) using the Up/Down arrow key and press

ENTER.

Step 4. Press the FREQ/DIST key to set the frequency limits. For a TMA-S amplifier, set F1 to 800 MHz and F2 to 925 MHz.

Step 5. Perform a two-port calibration of the Site Master (page 3-4).

Step 6. Connect the RF Out port of the Site Master to the ANT connector of the TMA. Step 7. Connect the RF In port of the Site Master to the RX connector of the TMA.

TMA-S

TEST PORT CABLE (OPTIONAL)

RF IN TEST PORT

EXTERNAL POWER

SUPPLY (40-115)

RX ANT

TEST PORT CABLE (OPTIONAL)

RF OUT TEST PORT

(BIAS TEE)

Site Master S251C

1

2

START AUTO

CAL SCALE

3 4

SAVE RECALL

SETUP SETUP

5 6

LIMIT MARKER

7 8

ESCAPE

CLEAR

ENTER

SAVE	RECALL	RUN
DISPLAY	DISPLAY	HOLD
9	0	+/-

ON PRINT

OFF.

MODE

FREQ/DIST

AMPLITUDE

SWEEP

Figure 4-8. TMA-S Measurement Setup

SYS

4-13

Image 58

Anritsu S251C manual TMA Measurements, Tma-S

Contents

Site Master Model S251C Antenna Cable Analyzer Page Warranty Page Table of Contents Cable & Antenna Analysis Iii/iv Introduction Standard AccessoriesDescription Optional Accessories Options Performance Specifications Description Site Master Performance Specifications 2 Preventive Maintenance ESD Precautions Annual Verification Anritsu Service Centers Test Connector Panel Chapter Functions and Operations Front Panel Overview Active Function Block Soft Keys Function Hard Keys Mode Keypad Hard Keys Clear Auto Soft Keys MODE=FREQ FREQ/DIST Softkeys MODE=DTF FREQ/DIST Softkeys Functions and Operations Amplitude Power Monitor Menu Option MODE=POWER Monitor Softkeys RF Source Menu MODE=RF Source Softkeys Limit Segment 1 Segment SYS Symbols Self Test Error Codes Self Test Errors Range Errors ERRORD2 Charging the Battery in the Site Master Battery InformationCharging a New Battery Charging the Battery in the Optional Charger Battery Charge Indicator Battery Life Important Battery Information Power On Procedure Chapter Getting Started Select the Frequency or Distance Calibration Calibration Procedure Single Port Calibration Calibration Procedure Dual Port RF in Test Port RF OUT Test Port Save and Recall a Setup Setting the ScaleSave and Recall a Display Recalling a Display Changing the Units Set the Distance and Cable TypeChanging the Display Language Printing Printing a Screen Printer Switch Settings Printer Using the Soft Carrying Case Using the Site Master Soft Carrying Case One Port Measurements Line Sweep Fundamentals Information Required for a Line Sweep Measurements Typical Line Sweep Test Procedures System Return Loss Measurement 2is an example of a typical system return loss trace Procedure Cable Loss Mode Insertion Loss Measurement Type Attenuation dB/ft Length ft = Loss dB Procedure Return Loss Mode Distance-To-Fault DTF Transmission Line Test Procedure DTF-Return Loss Mode Procedure DTF-SWR Mode Antenna Subsystem Return Loss Test Vswr Two Port Measurements Introduction TMA Measurements TMA-S TMA Gain Measurement After Calibration TMA-DD 12. TMA-DD Gain Measurement TMA-D 14. TMA-D Gain Measurement Antenna to Antenna Isolation 15. System Isolation Quency settings for common systems Antenna-to-Antenna Isolation Measurement 21/4-22 Features System Requirements Installation Communication Port Setting Interface Cable Installation Using Software ToolsDownloading Traces from the Site Master Plot Capture Plot Properties Trace Overlay or Plot Overlay Saving Traces Custom Cable List Saving a Plot to a Spreadsheet Creating a Database Printing Formats Coaxial Cable Technical Data Appendix a Reference Data Appendix a Reference Data A-4 Appendix B Windowing Examples Appendix B Windowing B-4