Printer Switch Settings | Anritsu S251C guide

Chapter 3 Getting Started

Step 4. Press the PRINTER soft key and select from the displayed menu of supported printers.

Step 5. Press the PRINT key. (Figure 3-6).

PRINTER

Site Master S251C

PRINTER

CHANGE

DATE

		ESCAPE
1	2	CLEAR
1	2

START AUTO

CAL SCALE

3 4

SAVE RECALL

SETUP SETUP

5 6

LIMIT MARKER

ENTER

7 8

SAVE RECALL RUN

DISPLAY DISPLAY HOLD

9 0 +/-

PRINT

ON PRINT

OFF.

SYS

MODEFREQ/DIST AMPLITUDE SWEEP

Figure 3-6-. PRINTER Soft Key and PRINT Key

Printer Switch Settings

Set the switches, SW1, SW2, and SW3, on the Seiko DPU-414 thermal printer as follows:

Switch	1	2	3	4	5	6	7	8
SW1	OFF	ON	ON	ON	ON	OFF	ON	ON
SW2	ON	ON	ON	ON	ON	ON	ON	OFF
SW3	ON	ON	ON	OFF	OFF	ON	ON	ON

Set the switches on the serial-to-parallel interface cable to the HP Deskjet 350 ink jet printer as follows:

SW1	SW2	SW3	SW4	SW5	SW6	SW7	SW8
OFF	ON	OFF	OFF	OFF	OFF	ON	OFF

3-9

Image 44

Anritsu S251C manual Printer Switch Settings

Contents

Site Master Model S251C Antenna Cable Analyzer Page Warranty Page Table of Contents Cable & Antenna Analysis Iii/iv Description Standard AccessoriesIntroduction Optional Accessories Options Performance Specifications Description Site Master Performance Specifications 2 Preventive Maintenance ESD Precautions Annual Verification Anritsu Service Centers Test Connector Panel Chapter Functions and Operations Front Panel Overview Active Function Block Soft Keys Function Hard Keys Mode Keypad Hard Keys Clear Auto Soft Keys MODE=FREQ FREQ/DIST Softkeys MODE=DTF FREQ/DIST Softkeys Functions and Operations Amplitude Power Monitor Menu Option MODE=POWER Monitor Softkeys RF Source Menu MODE=RF Source Softkeys Limit Segment 1 Segment SYS Symbols Self Test Error Codes Self Test Errors Range Errors ERRORD2 Battery Information Charging a New BatteryCharging the Battery in the Site Master Charging the Battery in the Optional Charger Battery Charge Indicator Battery Life Important Battery Information Power On Procedure Chapter Getting Started Select the Frequency or Distance Calibration Calibration Procedure Single Port Calibration Calibration Procedure Dual Port RF in Test Port RF OUT Test Port Save and Recall a Display Setting the ScaleSave and Recall a Setup Recalling a Display Changing the Display Language Set the Distance and Cable TypeChanging the Units Printing Printing a Screen Printer Switch Settings Printer Using the Soft Carrying Case Using the Site Master Soft Carrying Case One Port Measurements Line Sweep Fundamentals Information Required for a Line Sweep Measurements Typical Line Sweep Test Procedures System Return Loss Measurement 2is an example of a typical system return loss trace Procedure Cable Loss Mode Insertion Loss Measurement Type Attenuation dB/ft Length ft = Loss dB Procedure Return Loss Mode Distance-To-Fault DTF Transmission Line Test Procedure DTF-Return Loss Mode Procedure DTF-SWR Mode Antenna Subsystem Return Loss Test Vswr Two Port Measurements Introduction TMA Measurements TMA-S TMA Gain Measurement After Calibration TMA-DD 12. TMA-DD Gain Measurement TMA-D 14. TMA-D Gain Measurement Antenna to Antenna Isolation 15. System Isolation Quency settings for common systems Antenna-to-Antenna Isolation Measurement 21/4-22 Features System Requirements Installation Communication Port Setting Downloading Traces from the Site Master Using Software ToolsInterface Cable Installation Plot Capture Plot Properties Trace Overlay or Plot Overlay Saving Traces Custom Cable List Saving a Plot to a Spreadsheet Creating a Database Printing Formats Coaxial Cable Technical Data Appendix a Reference Data Appendix a Reference Data A-4 Appendix B Windowing Examples Appendix B Windowing B-4