Parameter

Description

Option

 

 

 

 

 

 

 

Switch Function

This option enables you to specify the function of

Disabled

 

 

 

the button:

Break/Wake

 

 

 

1. Disabled: The button functions is disabled

 

 

 

 

2. Break/Wake: The button functions are same as

 

 

 

 

suspend button in APM mode. When the button is

 

 

 

 

depressed, the system enters a suspended state until

 

 

 

 

the button is again depressed to return the system to

 

 

 

 

normal operating status.

 

 

 

Mode Use IRQ

If you want an incoming call on a modem to

N/A

 

 

 

automatically resume the system from a power-

3

 

 

 

saving mode, use this item to specify the interrupt

4

 

 

 

request line (IRQ) that is used by the modem. You

 

 

 

5

 

 

 

might have to connect the fax/modem to the

 

 

 

7

 

 

 

mainboard Wake On Modem connector for this

 

 

 

9

 

 

 

feature to work.

 

 

 

 

10

 

 

 

 

11

 

 

 

 

 

 

 

Hot Key Function As

This option allows you to set the Hot Key

Disabled

 

 

 

functionality to one of the following states:

Power Off

 

 

 

Disabled, Power Off and Suspend

Suspend

 

 

 

 

 

 

 

HDD Power Down

This option lets you specify the IDE HDD idle time

Disabled

 

 

 

before the device enters the power down state. This

1~15 Mins

 

 

 

item is independent from the power states previously

 

 

 

 

described in this section (Standby and Suspend).

 

 

 

 

 

 

 

 

Soft-off by PWR-BTTN

This is a specification of ACPI and supported by

Instant Off

 

 

 

hardware. When Delay 4 sec. is selected, the soft

Delay 4 Sec

 

 

 

power switch on the front panel can be used to

 

 

 

 

control power On, Suspend and Off.The other setting

 

 

 

 

is Instant-Off, where the soft power switch is only

 

 

 

 

used to control On and Off, there is no need to press

 

 

 

 

4 sec, and there is no Suspend.

 

 

 

 

 

 

 

 

After AC Power Lose

This item specifies when your system reboot after a

Always Off

 

 

 

power failure or interrupt occurs.

Always On

 

 

 

 

Former-Sts

 

 

 

 

 

 

 

PM Wake Up Events

Disabled: The specified event's activity will not affect

Press Enter

 

 

 

the PM Timers/wake up the system.

 

 

 

 

Enabled: The specified event's activity will affect the

 

 

 

 

PM Timers/wake up the system.

 

 

 

 

For example, if you have a modem on IRQ3, you can

 

 

 

 

turn On IRQ3 as a wake-up event, so an interrupt

 

 

 

 

from the modem can wake up the system. Or you

 

 

 

 

may wish to turn Off IRQ12 (the PS/2) mouse as a

 

 

 

 

wake-up event, so accidentally brushing the mouse

 

 

 

 

does not awaken the system.

 

 

 

 

 

 

 

Chapter 2

36

Page 43
Image 43
Aspire Digital T130 manual Break/Wake, Power Off, Delay 4 Sec, Former-Sts