Avaya G350 Preparing a G350 without an S8300 for

Preparing for configuration

Step 1: Prepare configuration equipment

34 Installation of the G350 Media Gateway

December 2003

Preparing a G350 without an S8300 for

configuration

If some of the configuration will be done on-site and some remotely, the supporting technician will

perform the local configuration and set up the G350 for the remote configuration. You will need to assist

the technician (see Assisting a combined remote and on-site configuration on page 40).

If all the configuration will be done remotely (see Step 2: Assist the configuration on page 40), you need

to enable a modem on the CON port of the G350 and connect the modem, as follows:

1Prepare a PC with a CD-ROM drive and a TFTP server on the network. This may be needed fo r

installing software and firmware upgrades.

NOTE:

When uploading firmware from the S8300 using TFTP, you may need to enable TFTP

service in the Set LAN Security parameters of your web server.

NOTE:

Firmware upgrades for the G350 and media modules can either be installed from CD or

downloaded from the Web.

2Download GIW (Gateway Installation Wizard) from the Avaya website

(support.avaya.com/avayaiw) to the laptop computer. The laptop should be running Windows

2000 or Windows XP to support GIW.

3Plug one end of the provided flat RJ-45 to RJ-45 cable into the provided DB-9 adapter.

4Plug the RJ-45 connector at the other end of the cable into the CON port of the G350.

5Plug the DB-9 end of the flat cable into the COM port of the laptop computer.

6From your laptop computer, double-click the GIW icon to run GIW. The opening screen appears:

Contents

Main Page Page Page Contents About this book 9 1 Before you start 13 2 Installing the Avaya G350 Media Gateway 19 3 Preparing for configuration 33 4 Connecting devices 43 Page Page About this book Overview Audience Downloading this book and updates from the Web Downloading this book Safety labels and security alert labels Related resources Technical assistance Within the US International Trademarks Sending us comments 1 Installation workflows Full installation Staging Installation of a staged G350 Gathering information Unpacking 1 2 3 4 5 Site requirements Environmental Verification Power Verification Grounding Verification Required equipment Page 2 Gateway Step 1: Mount the G350 chassis Mounting the G350 in a rack Page Page Mounting the G350 on a wall Placing the G350 on a table Step 2: Install the media modules Combination limitations Allocating slots Page Inserting the S8300 Media Server module 1 2 3 4 5 Inserting media modules 1 2 3 4 5 Step 3: Attach ground conductors General grounding requirements Approved grounds Page Step 4: Connect power to the G350 Page 3 Step 1: Prepare configuration equipment Preparing a G350 without an S8300 for Page Preparing a G350 with an S8300 for Page Page Page Step 2: Assist the configuration Assisting a remote configuration Assisting an on-site configuration Assisting a combined remote and on-site Page Page 4 Step 1: Connect the network Step 2: Connect IP telephones Step 3: Connect non-IP telephones and trunks Connecting an analog telephone 1 2 Connecting a DCP telephone 1 2 Connecting an analog trunk 1 Connecting an E1/T1 trunk 1 Connecting an ISDN BRI trunk 1 Step 4: Install circuit protection Step 5: Connect to the Wide Area Network (WAN) Connecting the G350 to the WAN 1 2 Step 6: Install the Coupled Bonding Conductor Step 7: Install the Avaya Partner Contact Closure Adjunct 1 2 3 5 Step 1: Test the installation Testing telephones Testing trunks LSP failover testing Step 2: Remove the installation equipment A G350 Media Gateway specifications Power Cord Specifications Page Index A B C D H I L M N T U W