Manuals / Avocent / TV and Video / Home Theater Server

Avocent Cyclades-PR4000 DATA-LINK Protocols Encapsulation, PPP The Point-to-Point Protocol

Models: Cyclades-PR4000

1 174

Download 174 pages 19.29 Kb

Page 79

Cyclades-PR4000

CHAPTER 10 DATA-LINK PROTOCOLS (ENCAPSULATION)

Each encapsulation option is presented in a separate section in this chapter. Not all data-link protocols are available for all interfaces.

PPP (The Point-to-Point Protocol)

PPPis the only encapsulation option than can be either synchronous or asynchronous. It is important to choose between them in CONFIG =>INTERFACE =><LINK> =>PHYSICAL before entering the Encapsulation menu. The menu options depend on this choice. (Note: not all interfaces support both the synchronous and asynchronous modes. In this case, there is no physical menu.)

The configuration of the PPP data-link protocol is confined to one menu, CONFIG =>INTERFACE =><LINK> =>ENCAPSULATION =>PPP. Information about all the parameters appearing in this menu is provided in the table below. Not all parameters will appear for all interfaces.

PPP Menu CONFIG =>INTERFACE =><LINK> =>ENCAPSULATION =>PPP

Parameter	Description
MLPPP	Enables Multilink PPP on this interface. MLPPP is described in the CyROS
	Reference Guide for each interface that supports it.
Leased, Dial-in, etc.	Applies for MLPPP = Yes. Type of line used on this link.
Identification for This Bundle	Applies for MLPPP = Yes and Dial-outor Leased. An integer value.
Total Number of lines for	Applies for MLPPP = Yes. Maximum number of links allowed in the bundle.
This Bundle
PPP Inactivity Timeout	Applies to asynchronous connections only. The connection is closed when
	data does not pass through the line for this period of time.
Enable Van Jacobson IP	Allows the link to receive compressed packets. This type of compression is
Header Compression	useful for low-speed links and/or small packets. It is not recommended for fast
	links, as it requires CPU time.
Transmit Compressed	Applies when Enable Van Jacobson IP Header Compression is Yes. This
Packets	parameter causes the link to send compressed packets.

Chapter 10 - Data-Link Protocols (Encapsulation)

79

Image 79

Avocent Cyclades-PR4000 installation manual DATA-LINK Protocols Encapsulation, PPP The Point-to-Point Protocol

Contents

Cyclades-PR4000 FCC Warning Statement Cyclades-PR4000 Installation ManualCanadian DOC Notice Table of Contents IP Bridge 119 139 156 HOW to USE this Manual Installation Assumptions Icons CONFIG=INTERFACE=LText Conventions Convention DescriptionCyclades Technical Support and Contact Information CONFIGURATION=ALLUSA Cyclades CorporationWhat is in the BOX Slot with Swan RSV Card or DB-25 Male Swan Expansion CardWith M.34 Interface Provisioning the T1/E1 Dialup Lines Signaling ISDN-PRI CCS or CASNumber of Phone Lines Phone Numbers, Hunting Groups, and Hunting Sequence Isdn Switch Type ISDN-PRI onlyOne-Way or Two-Way Service Data/Voice SupportTermination at the Customer Premises Signaling Method and Dialing Method T1 CAS-BR onlyLine Coding FramingUsing CyROS Menus Lmi-typeANSI, Group of four, None a Special Keys Discard, save to Flash, or save to Run configurationCyROS Management Utility Cyros Management UtilityCyROS Management Utility Slot #2 Port #26 Status CyROS Management Utility Operating the Front-Panel Display LCDModem Order Modem OverviewND no Slot/Link OrderInterface Overview Screen Interface OverviewSyslog Messages IP TrafficSystem Info STEP-BY-STEP Instructions for Common Applications Example 1 Using the PR4000 as a Remote Access ServerMask PR4000 Telephone Number RadiusServer NetworkNAT Step ONEParameter Example Your Application IP MTUE1/T1 Controller Menu Parameters Radius Server Parameters Step ThreeStep Five Step FourInstructions for listing the configuration 192.168.0.11 192.168.0.0Host PR4000 HostParameter Example Your Application Swan Physical Menu Parameters Global Assigned because the IP 10 PPP Encapsulation Menu Parameters MlpppStep SIX 11 Static Route Menu ParametersStep Seven Configuration =TO Flash Step NineStep Eight Instructions for listing the configuration IP Network Protocol Configuration of the Ethernet InterfaceParameter Description Incoming IP Accounting Config =RULES LIST=IP=CONFIGURE RULES=ADD RULE=ALLOW200.240.240.8 200.240.240.4 IP Bridge200.240.240.9 200.240.240.3 200.240.240.2 200.240.240.1 PR4000 Link PR3000Other Parameters Clock Source is always External Swan InterfaceStep TWO Protocol Be used for authentication Rest Same as Add Group E1 and T1 INTERFACES, Without SignalingOtherwise, see chapter Menu Item Description CONFIG=INTERFACE=T1/E1=CHANNELHdlc Step Four Controller Menu Tree E1 and T1 INTERFACES, with SignalingCONFIG=CONTROLLER=T1/E1 Integrated Isdn Line CCS Signaling Mode ISDN-PRIBRI Line Router Analog Line Remote Users ISDN-PRI Interface Configuration Menu Tree Timeout function Integrated CAS Line CAS Signaling ModeRouter Analog Line Remote Users All Channels Parameters Independent of Signaling ModeInterface E1/T1 CAS One Channel RangeMultilink Options Channel Menu CONFIG=INTERFACE=T1/E1=CHANNELModem Internet Service ProviderIP Address PR4000 LANServerIP Address Router a SIgnaling Config Interface E1/T1 Channel=MODEMS =DIGITAL Modem Parameter Description Copy From Channel Interface T1/E1 Channel Wizards TS ProfileRAS Profile LAN-to-LAN ProfileAnsi Menu Items Description12 Parameters SET by the RAS Wizard 13 Parameters SET by the LAN-TO-LAN Wizard Network Protocol Network ProtocolsIP Protocol Detailed Incoming IP Accounting Transparent Bridge Protocol PPP The Point-to-Point Protocol DATA-LINK Protocols EncapsulationPPP Menu Char Hdlc PppcharFrame Relay Parameter Description 200.1.1.1 DlciSalvador Recife Network São Paulo Rio de Janeiro NetworkParameter Description Modem or Switch / DCERouter / DTE Step ONE Menu With PAD Packet Assembler/Disassembler Dynamic Routing Routing ProtocolsRouting Strategies Static Routing10.0.0.0 Static Routes142.10.0.0 Mask 192.168.100.0Interfaces UnnumberedAdd Static Route Menu Config =STATIC Routes =IP =ADD Route RIP Configuration Ospf Ospf Configuration on the Interface 10Mbps, 65 for T1, 1785 for 56kbps, etc Ospf Global Configurations =PASSWORD CONFIG=STATIC ROUTES=IP=ADD ROUTE=OSPF Advertises this=ROUTING Protocol =OSPF =ADVERTISE this NON-OSPF Interface Applies when Area Range N Status is Active =IP=OSPF=AREA=AUTHENTICATION Type Only when Virtual Link Status is ActiveBGP-4 Configuration 255.255.255.0 200.50.50.0 PR3000 200.200.200.2 Tele Brutus Example System with PR3000 in AS 100 Being ConfiguredCONFIG=IP=BGP4=BGP NETWORK=ADD CONFIG=IP=BGP4=GLOBALRoute Reflector Client CONFIG=IP=BGP4=NEIGHBOR=ADDRouting Protocols 107 Up Ro 100.10.0.0/16 Route PR3000 RredParameter Description Seq Rule Message From Tele Popeye Route Map RoutesRouting Protocols 110 DiscardedDiscarded RoutesRoutes Seq RuleMessage From Tele Popeye Rule CONFIG=IP=BGP4=ROUTE MAP=ADD CONFIG=IP=BGP4=AGGREGATE ADDRESSES=ADD CYROS, the Operating System Creation of user accounts and passwordsCreation of the host table Slip IP Accounting Detailed information can be accessed via SnmpPR4000 With NAT Network Address TranslationTranslated Types of Address Translation Menu Option Description Interface. Five minutes is a reasonable time NAT 122 Rules and Filters Configuration of IP FiltersRule List Rules ListBastion Host 10.0.0.0 Extension to Network Exterior Router Perimeter Network Slot 192.168.0.0Let Mail out Exterior RouterLet Telnet Connections Out Filters and Rules 127 TCP Interior Router Output for IP Filtering ExampleStop Telnets From the Outside Except Bastion Host Stop Forged Packets Don’t Allow Access to NewsFilters and Rules 131 Link 33.33.33.1 25% or less Traffic Rule ListsClient B Filters and Rules 133 Filterlist Name traffic1 Output Showing Parameters for Traffic Rule Example Back Operator Start Number Mac Address 00 60 2E 00 11 IPX Internetwork Packet ExchangeIPX Network Internal NetworkConfiguring Other Interfaces Configuring the Ethernet InterfaceEnabling IPX Routing Frame RelayParameter Value for the Example Routing Table for the Example SAP Service Advertisement Protocol TableVirtual Private Network Configuration Virtual Private Network Configuration 143 IP172.16.0.0 Link Link IP10..255.255.0Router IP Address RSG3 Remote IP Network 9.1 Security Gateway Router LinkVirtual Private Network Configuration 145 Virtual Private Network Configuration 146 Test CPU Boot Code step Appendix a TroubleshootingEvent Port 2 LED Morse code What to Do if the Router Does Not Work or Stops WorkingTesting the Ethernet Interface Testing the WAN Interface Testing the Two T1/E1 Ports Use of a Cross Cable for Testing T1/E1 Ports and ModemsHow to Test the Modems DPS Test Results 113 Physical Specifications Appendix B. Hardware SpecificationsGeneral Specifications Power RequirementsRTS DTR External InterfacesConsole Port Console PortEthernet Port Ethernet PortTPTX+ Tptx TPRX+ Tprx T1/E1 Interface T1 and E1Straight-Through Cable CablesCross Cable Router-MD / V.35 Cable DB-25 Male Cyclades Router Signal Pin PGndPin 13 B 10 F 15 S 17 T 24 W 11 U DB-25 to M.34 Adapter Cross Cable for Testing the T1/E1 Ports TxD/V.35 B TxD/V.35 a RxD/V.35 B RxD/V.35 a Signal Pin PGndISO 2110 Standard Cable DB-25 Male Modem Cyclades RouterRJ-45 Male E1 / DB-15 CableProcedure Appendix C Configuration Without a ConsoleRequirements Step Two Appendix D Installation of Additional Digital ModemsAppendix D Installation of Additional Digital Modems Step OneStep Five Step FourClamp Slot Step SixStep Seven Step Nine Step EightClamp Step Eleven Step TenIndex 172 Index 173 Cyclades Philippines