Cabling | B&B Electronics EIR618-2SFP-T specs

Cabling

Twisted-pair segment can be either unshielded twisted pair (UTP) or shielded twisted pair (STP) cabling. The cable between the link partner (switch, hub, workstation, etc.) and the converter must be less than 100 meters (328 ft.) long and comply with the IEEE 802.3ab 1000Base-T standard for Category 5e or above.

Single-mode fiber links must use 9/125μm single-mode fiber cable. Multi-mode fiber links must use 50/125 or 62.5/125μm multi-mode fiber cable. The small form-factor pluggable (SFP) is a compact optical transceiver

To connect the transceiver and LC cable, follow the steps shown below:

First, insert the transceiver into the SFP module. The triangle mark identifies bottom of the module.

Transceiver to the SFP module

Manual Documentation Number: EIR618-2SFP-T_5107m

11

B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax 815-433-5104 – www.bb-elec.com

B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444 – Fax +353 91-792445 – www.bb-europe.com

Image 23

B&B Electronics EIR618-2SFP-T manual Cabling

Contents

Product Description Page Eighteen Port Managed Industrial Ethernet Switches V2.07 Firmware VersionV1.07 Kernel Version FCC Warning Page Content Console Management About Web-based Management Preparing for Web Management Port Mirroring Rate Limiting Vlan configuration 102 101Page Introduction Features ¾ Gvrp ¾ Port Based Vlan ¾ 802.1 Q Tag Vlan Spanning tree Software SpecificationManagement Port Trunk with Relay Alarm Quality of serviceClass of service Login Security Package Contents D x H 2.83 x 4.13 x 5.98 in 7.2mm x 10.5mm x 15.2 cm Physical DimensionFront Panel of the industrial switch Front Panel Top View Top Panel of the industrial switch LED Indicators Ports „ Gigabit Copper/SFP Mini-GBIC combo port Straight Through Cable Schematic Cross Over Cable Schematic Cabling Insert the fiber cable into the transceiver Remove LC connector Wiring the Power Inputs Wiring the Fault Alarm Contact DIN-Rail Mounting Rear Panel of the switch DIN-Rail Manual Documentation Number EIR618-2SFP-T5107m Panel Mounting Installation Steps Hardware Installation Ring Application Network Application Coupling Ring Application Dual Homing Application Orange/White Green/White Blue Blue/White Brown/White Connecting to the Console PortDB9 Connector RJ-45 Connector Pin Assignment Settings of communication parameters Login in the Console Interface CLI Management Console login interfaceCLI command interface Commands Level System Location Commands Set ListSystem Commands Set System Name Subnet-mask PasswordSystem Contact Ip-address IP address Hours 101001000auto Port Commands SetPortid Full half Value Enable Disable Trunk Commands Set GroupID Vlan Commands Set PortNumber Group NamePortNumbers GroupName Seconds Spanning Tree Commands Set~61440 Stp-path-cost Spanning-treeHello-time seconds Forward-time seconds TrueFalse AutoTrueFalse Igmp Commands Set QOS Commands Set Mac / Filter Table Commands Set Snmp Commands Set Read View Name Write View Name Notify View NameNoAuthNoPrivAuthNoP RivAuthPriv ExactPrifix View Name SNMPV3 agent Port Mirroring Commands SetRemove specified Mibview table Words 802.1x Commands SetPort ID Number Disable reject acceptSec Authorize Tftp Commands SetSystemLog, Smtp and Event Commands Set SystemlogSMTPBoth ClientserverbothAccount Index Email address Start time End time Sntp Commands Set 1st Ring Port 2nd Ring Ring Commands SetMinute Timezone Dual Homing Port Coupling PortControl Port Preparing for Web Management About Web-based Management System Login System information interface System Information IP configuration interface IP Configuration Dhcp Client information is displayed Dhcp Server System configurationDhcp Server Configuration interface Dhcp Server Client Entries Port and IP Bindings interface Dhcp Server Port and IP BindingsDhcp Client Entries interface Restore Configuration interface Tftp Update FirmwareTftp Restore Configuration Update Firmware interface Tftp Server IP Address Enter the Tftp server IP Tftp Backup ConfigurationSystem Event Log Syslog Configuration Syslog Configuration interface System Event Log Smtp Configuration Smtp Configuration interface System Event Log Event Configuration Event Configuration interface Fault Relay Alarm interface Fault Relay AlarmSntp Configuration Local Time Zone Conversion from UTC Time at 1200 UTC Daylight Saving Offset mins Enter the offset in minutes Switch Timer Displays the current time Click Apply IP Security Sntp Configuration interface IP Security interface User AuthenticationUser Authentication interface Port Statistics interface Port Statistics Port Control Port. To remove unwanted ports, select Port and click Aggregator settingPort Trunk Button to add Delete to delete Trunk Group Displays static trunk group information Aggregator InformationState Activity Port Trunk State Activity interface Port Trunk Port Mirroring interface Port Mirroring Rate Limiting interface Rate Limiting Vlan Configuration interface Vlan configurationVlan configuration Port-based Vlan VLAN-Port Based Add interface Vlan Port Based interface VLAN-Port Based Edit/Delete interface Use Button to delete the VlanUse Button to modify group name, Vlan ID, or add/remove Members of the existing Vlan group 802.1Q Vlan „ Hybrid Link Both Access Link and Trunk Link 802.1Q Vlan interface Group Configuration „ Click Apply button Group Configuration interface„ You can modify the Vlan group name and Vlan ID Rapid Spanning Tree Rstp System Configuration Rstp System Configuration interface Rstp Port Configuration Rstp Port Configuration interface „ Community Strings Snmp ConfigurationSystem Configuration Snmp System Configuration interface Trap Configuration User Profile SNMPV3 Configuration„ Privacy Password Enter the private password Context Table Snmp V3 configuration interface MIBview Table Access TableGroup Table „ QoS Policy select the QoS policy rule QoS ConfigurationQoS Policy and Priority Type „ Click Remove to remove an unwanted context name Port-based Priority QoS Configuration interface „ Click Apply button to make the settings effective Igmp ConfigurationCOS Configuration TOS Configuration Report Message sent from the querier Igmp router or switchMessage Description Query Ring Ring Interface Security 802.1X/Radius Configuration802.1x System Configuration interface 802.1x Per Port Setting interface 802.1x Port Configuration 802.1x Misc Configuration interface Misc Configuration Use the MAC address table to ensure the port security MAC Address Table MAC Filtering interface Static MAC Addresses interface All MAC Address interface Factory Default Click Reboot to reboot the system Save ConfigurationSystem Reboot Click Save to save the configuration to the flash memory 101 Trouble shooting MAC address StandardProtocol Transfer Rate Consumption Install „ LC Single mode 9/125um Back-planePower Supply Power IEC60068-2-27 Shock IEC60068-2-6 Vibration SafetyStability testing CE/EN60950-1 IEC60068-2-32 Free fall