Aggregator Information | B&B Electronics EIR618-2SFP-T specification

Aggregator Information

Displays static trunk group information.

Port Trunk—Aggregator setting interface (two ports are added to the left field with LACP

disable)

Port Trunk – Aggregator Information interface

State Activity

After setting up the LACP aggregator, port state activity can be configured.

Mark the port and click Apply . The port state activity will change to Active or Passive depending on its previous state.

Active: The port automatically sends LACP protocol packets.

Passive: The port responds only if it receives LACP protocol packets from the opposite device.

70	Manual Documentation Number: EIR618-2SFP-T_5107m
	Manual Documentation Number: EIR618-2SFP-T_5107m
	B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax	815-433-5104 – www.bb-elec.com
	B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444	– Fax +353 91-792445 – www.bb-europe.com

Image 82

B&B Electronics EIR618-2SFP-T manual Aggregator Information, State Activity, Displays static trunk group information

Contents

Product Description Page Eighteen Port Managed Industrial Ethernet Switches Kernel Version Firmware VersionV1.07 V2.07 FCC Warning Page Content Console Management About Web-based Management Preparing for Web Management Port Mirroring Rate Limiting Vlan configuration 101 102Page Features Introduction ¾ Port Based Vlan ¾ 802.1 Q Tag Vlan ¾ Gvrp Port Trunk with Software SpecificationManagement Spanning tree Login Security Quality of serviceClass of service Relay Alarm Package Contents Front Panel Physical DimensionFront Panel of the industrial switch D x H 2.83 x 4.13 x 5.98 in 7.2mm x 10.5mm x 15.2 cm Top Panel of the industrial switch Top View LED Indicators Ports Straight Through Cable Schematic Cross Over Cable Schematic „ Gigabit Copper/SFP Mini-GBIC combo port Cabling Insert the fiber cable into the transceiver Remove LC connector Wiring the Power Inputs Wiring the Fault Alarm Contact Rear Panel of the switch DIN-Rail DIN-Rail Mounting Manual Documentation Number EIR618-2SFP-T5107m Panel Mounting Hardware Installation Installation Steps Network Application Ring Application Coupling Ring Application Dual Homing Application Pin Assignment Connecting to the Console PortDB9 Connector RJ-45 Connector Orange/White Green/White Blue Blue/White Brown/White Login in the Console Interface Settings of communication parameters CLI command interface Console login interfaceCLI Management Commands Level System Name Commands Set ListSystem Commands Set System Location Ip-address PasswordSystem Contact Subnet-mask Hours IP address Full half Port Commands SetPortid 101001000auto Enable Disable Value Trunk Commands Set Vlan Commands Set GroupID GroupName Group NamePortNumbers PortNumber ~61440 Spanning Tree Commands SetSeconds Forward-time seconds Spanning-treeHello-time seconds Stp-path-cost AutoTrueFalse TrueFalse QOS Commands Set Igmp Commands Set Mac / Filter Table Commands Set Snmp Commands Set ExactPrifix NameNoAuthNoPrivAuthNoP RivAuthPriv Read View Name Write View Name Notify View Mibview table Port Mirroring Commands SetRemove specified View Name SNMPV3 agent Port ID 802.1x Commands SetWords Sec Disable reject acceptNumber SystemLog, Smtp and Event Commands Set Tftp Commands SetAuthorize Index Email address ClientserverbothAccount SystemlogSMTPBoth Sntp Commands Set Start time End time Timezone Ring Commands SetMinute 1st Ring Port 2nd Ring Control Port Coupling PortDual Homing Port About Web-based Management Preparing for Web Management System Login System Information System information interface IP Configuration IP configuration interface Dhcp Server Client Entries Dhcp Server System configurationDhcp Server Configuration interface Dhcp Client information is displayed Dhcp Client Entries interface Dhcp Server Port and IP BindingsPort and IP Bindings interface Update Firmware interface Tftp Update FirmwareTftp Restore Configuration Restore Configuration interface System Event Log Syslog Configuration Tftp Backup ConfigurationTftp Server IP Address Enter the Tftp server IP System Event Log Smtp Configuration Syslog Configuration interface System Event Log Event Configuration Smtp Configuration interface Event Configuration interface Sntp Configuration Fault Relay AlarmFault Relay Alarm interface Local Time Zone Conversion from UTC Time at 1200 UTC Switch Timer Displays the current time Click Apply Daylight Saving Offset mins Enter the offset in minutes Sntp Configuration interface IP Security User Authentication interface User AuthenticationIP Security interface Port Statistics Port Statistics interface Port Control Button to add Aggregator settingPort Trunk Port. To remove unwanted ports, select Port and click Delete to delete Trunk Group State Activity Aggregator InformationDisplays static trunk group information Port Trunk State Activity interface Port Mirroring Port Trunk Port Mirroring interface Rate Limiting Rate Limiting interface Vlan configuration Port-based Vlan Vlan configurationVlan Configuration interface Vlan Port Based interface VLAN-Port Based Add interface Members of the existing Vlan group Use Button to delete the VlanUse Button to modify group name, Vlan ID, or add/remove VLAN-Port Based Edit/Delete interface „ Hybrid Link Both Access Link and Trunk Link 802.1Q Vlan Group Configuration 802.1Q Vlan interface „ You can modify the Vlan group name and Vlan ID Group Configuration interface„ Click Apply button Rstp System Configuration Rapid Spanning Tree Rstp Port Configuration Rstp System Configuration interface Rstp Port Configuration interface System Configuration Snmp Configuration„ Community Strings Trap Configuration Snmp System Configuration interface Context Table SNMPV3 Configuration„ Privacy Password Enter the private password User Profile Snmp V3 configuration interface Group Table Access TableMIBview Table „ Click Remove to remove an unwanted context name QoS ConfigurationQoS Policy and Priority Type „ QoS Policy select the QoS policy rule QoS Configuration interface Port-based Priority TOS Configuration Igmp ConfigurationCOS Configuration „ Click Apply button to make the settings effective Query Message sent from the querier Igmp router or switchMessage Description Report Ring Ring Interface 802.1x System Configuration interface 802.1X/Radius ConfigurationSecurity 802.1x Port Configuration 802.1x Per Port Setting interface Misc Configuration 802.1x Misc Configuration interface MAC Address Table Use the MAC address table to ensure the port security Static MAC Addresses interface MAC Filtering interface Factory Default All MAC Address interface Click Save to save the configuration to the flash memory Save ConfigurationSystem Reboot Click Reboot to reboot the system Trouble shooting 101 Transfer Rate StandardProtocol MAC address Power „ LC Single mode 9/125um Back-planePower Supply Consumption Install CE/EN60950-1 IEC60068-2-32 Free fall SafetyStability testing IEC60068-2-27 Shock IEC60068-2-6 Vibration