Network Application | B&B Electronics EIR618-2SFP-T specification

Network Application

X-Ring Application

This switch incorporates the X-Ring Protocol to ensure network reliability and system restoration within 300 ms in the event of a connection failure. The X-Ring algorithm is similar to the spanning tree protocol (STP) algorithm but it has faster recovery time. The following figure below is an example of an X-Ring application.

20	Manual Documentation Number: EIR618-2SFP-T_5107m
	Manual Documentation Number: EIR618-2SFP-T_5107m
	B&B Electronics Mfg Co Inc – 707 Dayton Rd - PO Box 1040 - Ottawa IL 61350 - Ph 815-433-5100 - Fax	815-433-5104 – www.bb-elec.com
	B&B Electronics – Westlink Commercial Park – Oranmore, Galway, Ireland – Ph +353 91-792444	– Fax +353 91-792445 – www.bb-europe.com

Image 32

B&B Electronics EIR618-2SFP-T manual Network Application, Ring Application

Contents

Product Description Page Eighteen Port Managed Industrial Ethernet Switches Firmware Version V1.07Kernel Version V2.07 FCC Warning Page Content Console Management About Web-based Management Preparing for Web Management Port Mirroring Rate Limiting Vlan configuration 101 102Page Features Introduction ¾ Port Based Vlan ¾ 802.1 Q Tag Vlan ¾ Gvrp Software Specification ManagementPort Trunk with Spanning tree Quality of service Class of serviceLogin Security Relay Alarm Package Contents Physical Dimension Front Panel of the industrial switchFront Panel D x H 2.83 x 4.13 x 5.98 in 7.2mm x 10.5mm x 15.2 cm Top Panel of the industrial switch Top View LED Indicators Ports Straight Through Cable Schematic Cross Over Cable Schematic „ Gigabit Copper/SFP Mini-GBIC combo port Cabling Insert the fiber cable into the transceiver Remove LC connector Wiring the Power Inputs Wiring the Fault Alarm Contact Rear Panel of the switch DIN-Rail DIN-Rail Mounting Manual Documentation Number EIR618-2SFP-T5107m Panel Mounting Hardware Installation Installation Steps Network Application Ring Application Coupling Ring Application Dual Homing Application Connecting to the Console Port DB9 Connector RJ-45 ConnectorPin Assignment Orange/White Green/White Blue Blue/White Brown/White Login in the Console Interface Settings of communication parameters CLI Management Console login interfaceCLI command interface Commands Level Commands Set List System Commands SetSystem Name System Location Password System ContactIp-address Subnet-mask Hours IP address Port Commands Set PortidFull half 101001000auto Enable Disable Value Trunk Commands Set Vlan Commands Set GroupID Group Name PortNumbersGroupName PortNumber Seconds Spanning Tree Commands Set~61440 Spanning-tree Hello-time secondsForward-time seconds Stp-path-cost AutoTrueFalse TrueFalse QOS Commands Set Igmp Commands Set Mac / Filter Table Commands Set Snmp Commands Set Name NoAuthNoPrivAuthNoP RivAuthPrivExactPrifix Read View Name Write View Name Notify View Port Mirroring Commands Set Remove specifiedMibview table View Name SNMPV3 agent Words 802.1x Commands SetPort ID Number Disable reject acceptSec Authorize Tftp Commands SetSystemLog, Smtp and Event Commands Set Clientserverboth AccountIndex Email address SystemlogSMTPBoth Sntp Commands Set Start time End time Ring Commands Set MinuteTimezone 1st Ring Port 2nd Ring Dual Homing Port Coupling PortControl Port About Web-based Management Preparing for Web Management System Login System Information System information interface IP Configuration IP configuration interface Dhcp Server System configuration Dhcp Server Configuration interfaceDhcp Server Client Entries Dhcp Client information is displayed Port and IP Bindings interface Dhcp Server Port and IP BindingsDhcp Client Entries interface Tftp Update Firmware Tftp Restore ConfigurationUpdate Firmware interface Restore Configuration interface Tftp Server IP Address Enter the Tftp server IP Tftp Backup ConfigurationSystem Event Log Syslog Configuration System Event Log Smtp Configuration Syslog Configuration interface System Event Log Event Configuration Smtp Configuration interface Event Configuration interface Fault Relay Alarm interface Fault Relay AlarmSntp Configuration Local Time Zone Conversion from UTC Time at 1200 UTC Switch Timer Displays the current time Click Apply Daylight Saving Offset mins Enter the offset in minutes Sntp Configuration interface IP Security IP Security interface User AuthenticationUser Authentication interface Port Statistics Port Statistics interface Port Control Aggregator setting Port TrunkButton to add Port. To remove unwanted ports, select Port and click Delete to delete Trunk Group Displays static trunk group information Aggregator InformationState Activity Port Trunk State Activity interface Port Mirroring Port Trunk Port Mirroring interface Rate Limiting Rate Limiting interface Vlan Configuration interface Vlan configurationVlan configuration Port-based Vlan Vlan Port Based interface VLAN-Port Based Add interface Use Button to delete the Vlan Use Button to modify group name, Vlan ID, or add/removeMembers of the existing Vlan group VLAN-Port Based Edit/Delete interface „ Hybrid Link Both Access Link and Trunk Link 802.1Q Vlan Group Configuration 802.1Q Vlan interface „ Click Apply button Group Configuration interface„ You can modify the Vlan group name and Vlan ID Rstp System Configuration Rapid Spanning Tree Rstp Port Configuration Rstp System Configuration interface Rstp Port Configuration interface „ Community Strings Snmp ConfigurationSystem Configuration Trap Configuration Snmp System Configuration interface SNMPV3 Configuration „ Privacy Password Enter the private passwordContext Table User Profile Snmp V3 configuration interface MIBview Table Access TableGroup Table QoS Configuration QoS Policy and Priority Type„ Click Remove to remove an unwanted context name „ QoS Policy select the QoS policy rule QoS Configuration interface Port-based Priority Igmp Configuration COS ConfigurationTOS Configuration „ Click Apply button to make the settings effective Message sent from the querier Igmp router or switch Message DescriptionQuery Report Ring Ring Interface Security 802.1X/Radius Configuration802.1x System Configuration interface 802.1x Port Configuration 802.1x Per Port Setting interface Misc Configuration 802.1x Misc Configuration interface MAC Address Table Use the MAC address table to ensure the port security Static MAC Addresses interface MAC Filtering interface Factory Default All MAC Address interface Save Configuration System RebootClick Save to save the configuration to the flash memory Click Reboot to reboot the system Trouble shooting 101 Standard ProtocolTransfer Rate MAC address „ LC Single mode 9/125um Back-plane Power SupplyPower Consumption Install Safety Stability testingCE/EN60950-1 IEC60068-2-32 Free fall IEC60068-2-27 Shock IEC60068-2-6 Vibration