Ext Gating Input, Dualtone Examples

Ext Gating Input

This TTL compatible input can be used to gate the output signal on or off. Logic high voltage turns off the output. For further information on the Ext Gating Input, refer to section 2.0.

Dualtone Examples

The following table lists the parameters for some common Dualtone.

Name	Frequency 1	Frequency 2	On Time (Ton)	Off Time (Toff)
Dial Tone	350 Hz	440 Hz	1 mS	0 mS
Ring back	440 Hz	480 Hz	2,000 mS	4,000 mS
Busy	480 Hz	620 Hz	500 mS	500 mS
Reorder	480 Hz	620 Hz	250 mS	250 mS
DSN Preempt	440 Hz	620 Hz	1 mS	0 mS
European	420 Hz	440 Hz	various	various

Note: The Phase Offset field value may be set to any value to properly generate these tones.

BK Precision 4071 User Manual Rev.2.2

Page 40

Image 40

B&K 4071 user manual Ext Gating Input, Dualtone Examples

Contents

User’s Manual Page Model User’s Manual +K Precision Corp Table of Contents Warranty information Remote operationArbitrary waveform system DC Operation Option Introduction Description Feature summary Modes Sync out connector Installation and setupSIG Out connector External Modulation In connector External Trigger/Gating/FSK/BPSK input External Reference Input / Ext Arb. Clock connector External Arb Sync In / Out connectorRS232 Interface connector Line in connector Mode key Operating controls and keysField arrow keys Recall / Store key Numeric keys 0 to 9, Trigger keyÉ, ê, è, ç keys Clear key One Touch Mode KeysMHz/dBm, KHz/Vp-p/Sec, Hz/mVp-p/mS keys Operating mode selection Operating guideChanging frequency Changing level Modifying an existing value Changing valuesEntering a new value Basic Sinewave CW Mode Mode descriptionsSinewave Mode 000,000.00 Hz 10.0 dBm Internal AM Mode External AM Mode External AM Mode ParametersExternal AM Input gain 000,000.00 Hz PEP level -10.0 dBm Input Gain Internal FM Mode Internal FM Mode ParametersInt FM 1,000 Hz Pk dev 10,000 Hz 000,000.00 Hz 10.0 dBm Peak Frequency Deviation External FM Mode Parameters External FM ModeExternal FM Pk dev 10,000 Hz 000,000.00 Hz 10.0 dBm Internal PM Mode Internal PM Mode ParametersPeak Phase Deviation Int PM 1,000 Hz Pk dev 180 deg 000,000.00 Hz 10.0 dBm External PM Mode Parameters External PM ModeExternal PM Pk dev 180 deg 000,000.00 Hz 10.0 dBm Sweep Mode Up / Down sweep Sweep time Internal FSK Mode Internal FSK Mode ParametersMark Frequency Space Frequency External FSK Mode External FSK Mode ParametersExt FSK Mark 1,000,000.00 Hz Space 2,000,000.00 Hz 10.0 dBm Ext FSK Input Burst Mode Trig Ton 10,000 mS 000,000.00 Hz Off 10.0 dBm Burst Mode IntroductionBurst frequency Internal SSB Mode Internal SSB Mode ParametersInt SSB 1,000 Hz Upper Sideband 000,000.00 Hz 10.0 dBm Upper/Lower Sideband selections External SSB Mode Parameters External SSB ModeExternal SSB Upper Sideband 000,000.00 Hz 10.0 dBm Dtmf Generation Mode Dtmf generation # Duration 200 mS Delay Level -10.0 dBmDtmf Generation Mode Parameters Background Dtmf Delay Dtmf Duration Dtmf Detection Mode Dtmf Detection Mode ParametersDtmf detection on Ext Mod input 3 # a Dtmf detected digits Power & Voltage Measurement Mode Power & Voltage Measurement Mode ParametersPower Level Voltage Level Remote Mode Arbitrary ModeOther mode Internal Bpsk Mode Parameters Internal Bpsk ModeInt Bpsk 1,000 Hz 000,000.00 Hz 10.0 dBm External Bpsk Mode Parameters External Bpsk ModeExternal Bpsk 000,000.00 Hz 10.0 dBm Dualtone Generation Mode 10,000 Hz F2 Ton 000 mS Toff 10.0 Dualtone Examples Data Modulation Mode Using the Data Modulation ModeData Modulation Mode Parameters Baud Rate Downloading Modulation Message Data Example Message Triggering the Transmission Saving the Message Voltage Controlled Oscillator VCO Mode VCO Mode ParametersStart End 1,000,000.00 Hz 10.0 dBm End Frequency Remote Operation ConnectingChecking your connection with Hyper Terminal Remote Control Operation Remote Control Programming Rules Remote Control Commands Reset 4071 to Sine wave mode× Ø Returns C E1,0 Enable, Disable LCD echo to terminal K1.0 Enable, Disable front panel keys and rotary knobReport hardware and software versions Stp 31,500,000.00 Hz Linear Trig Up Time 10,000 mSF0-9 Move cursor to field 0 to ? or H Print help menu Remote Control Examples Example Quick Start Guide Arbitrary Waveform ModePin 9-pin cable Pin 25 pin cable adapter Introduction to the Arbitrary Waveform System Description of the Arbitrary Waveform Generator Switching Modes Feature SummaryFunction Generator Pulse Generator Arbitrary Waveform Mode Int Clock / Ext Clock / Lock Master Lock slave modePhase Continuous/Triggered mode Function Generator Mode Function Gen Wave Pos Ramp Rep Freq 100,000 Hz 000 mVWaveform Repetition Frequency Positive Only Pulse Generator ModeDuty Cycle Using WAVELOAD.EXE Downloading arbitrary waveformsSaving Arbitrary Waveforms Cwaveload /COMx /y /baudz filename.ext Using your own program Floating Point Format Data FormatsRules for Floating Point format Time & Value Floating Point Format Example #2 Digital Format Integer Format Rules for Integer format Rules for Hexadecimal format Hexadecimal FormatExample The data value E468 is handled as follows Rules for Binary format Binary FormatExample Arb Multiple Units LockingGenerator More on Phase Offsets Phase ResolutionStarting Address = Number of waveform points * Phase Offset Waveform Size Restrictions Example Arb Program Program Listing ARB.BAS Close System Subroutines Return Print #1, a Send integer value to Return Return Wiring Diagram DC Operation Option 4071 Specifications Operating Modes Software CD Remote Hardware Setup Appendix a CLS CLS Print Print Subroutines END SUB Television Remote Control Example Appendix B CLS Make sure a 4071 is attached to the serial port Print Limited Two-Year Warranty Service Information Savi Ranch Pkwy Yorba Linda, CA 92887 USA TEL